Manuale d’uso / di manutenzione del prodotto SR-C8002 del fabbricante Toshiba
Vai alla pagina of 31
TOSHIBA ST ORAGE DEVICE DIVISION SR-C8002 CD-R/CD-R W DRIVE PRODUCT SPECIFICA TION MA Y 2001 REV . 1.0 Specifications are subject to change without notice DOCUMENT NUMBER 14708.
SR-C8002 Rev.1.0 LIMITATION OF LIABILITY Those warranties in the express warranty separately agreed between TOSHIBA and your company are the only warranties given to the consumer and are in lieu of any other warranties, whether express or implied with regard to this component.
SR-C8002 Rev.1.0 DO NOT use this equipment in the system such as medical equipment which may cause personal injury or property damages resulting from malfunction of this equipment and unexpected data corruption or data error in reading operation.
SR-C8002 Rev.1.0 Contents 1. Introduction ---------------------------------------------------------------------------------------------------------------------- 1 2. Features -------------------------------------------------------------------------------------------------------------------------- 1 3.
SR-C8002 Rev.1.0 7.2. Current Drain -------------------------------------------------------------------------------------------------------18 7.2.1.Sleep ------------------------------------------------------------------------------------------------------------18 7.
1/24 SR-C8002 Rev.1.0 1. Introduction This document describes TOSHIBA's SR-C8002 CD-R/RW Drive. 2. Features SR-C8002 reads digital data stored on CD-ROM media and CD-Audio discs. The CD-ROM media has a 12 cm or 8 cm diameter. It typically contains approximately 600 MBytes or 200 MBytes of information respectively.
2/24 SR-C8002 Rev.1.0 3. Specifications 3.1.Performance (1) Applicable Write Format CD-R/RW: Disc at once, Track at once, Session at once, Packet write (2) Applicable Write Disc * 1 CD-R/RW: CD-DA, CD.
3/24 SR-C8002 Rev.1.0 (6) Transfer Rate Sustained Block Transfer Rate 776-1,800 Block/s (10.3-24X CAV) 300-450 Block/s (4-6X PCAV) Sustained Data Transfer Rate Mode-1: 10.3X-24X CAV 1,552-3,600 KByte/s 4X-6X PCAV 600-900 KByte/s Mode-2: 10.3X-24X CAV 1,769-4,104 KByte/s 4X-6X PACV 684.
4/24 SR-C8002 Rev.1.0 (10) Drawer Load/Release Load: Manual Release: (a) Electrical Release (Release Button) (b) Release by ATAPI command (c) Emergency Release (11) Air Flow Not Required (12) Acoustic Noise 40 dB (IEC 179 A weighted at 1 m) (13) Power Supply +5 V (details in Section 7) 3.
5/24 SR-C8002 Rev.1.0 3.2.3.Vibration (1) Operating (CD 10.3-24X Read) (1 Oct/min) ---------------- no hard error ----- 5 to 500 Hz 2.45 m/s 2 [0.25 G] ( 0-p) (excluding resonance point) (2) Operating (Write) (1 Oct/min) ---------------- no hard error ----- 5 to 500 Hz 2.
6/24 SR-C8002 Rev.1.0 3.3. Installation Conditions 15 ° 30 ° 15 ° 15 ° 15 ° 15 ° 15 ° 15 ° 15 ° 15 ° Figure 1 Mounting angle 3.3.1. Equipment (1) When mounting the equipment, use four M2-P0.4 tapping holes located on the left and right sides of the equipment.
7/24 SR-C8002 Rev.1.0 (4) Do not add the force beyond the indicated force on the top and bottom cover of the equipment. (The restricted force range for the top cover is shown in the Figure 2.) (For the bottom cover, the applied force should be less than 2N on whole area.
8/24 SR-C8002 Rev.1.0 ( Unit: mm ) Figure 3 External Dimensions.
9/24 SR-C8002 Rev.1.0 3.5. Reliabilites 3.5.1. Error Rate (1) Hard Read Error Rate (Byte Error Rate) ----- Allowing 5 Retries(default) ----- Mode 1:10 -15 Max Mode 2:10 -12 Max (2) Seek Error Rate --- Allowing 10 Retries 10 -6 Max (default) 3.
10/24 SR-C8002 Rev.1.0 C D-R / RW DRIVE MODEL SR-C8002 BLOCK DIAGRAM D isc Motor P UH Feed Motor P osition Detector R F Amp EQL T racking Amp F ocus Amp T A1323F P ower Driver P ower Driver T PIC1318 .
11/24 SR-C8002 Rev.1.0 5.Functions 5.1. Disc Data Configurations 5.1.1. CD-ROM Data Configurations Figure 5 shows how the data is structured in program units 1 block=1/75 s Time TNO TOC 0 Lead-in Min Sec Block Block 1 Min Sec Block 1 Block 2 2 approx.
12/24 SR-C8002 Rev.1.0 5.2. Power ON/OFF Timing Figure 7 shows the initialization sequence Power ON or ATAPI-RST System Initialization Focus Search Spindle ON Learning Stand-by "TEST UNIT READY" Command "Command" Receivable "Check Condition" Status "Good" Status Max.
13/24 SR-C8002 Rev.1.0 6.2.Signal summary The physical interface consists of single ended TTL compatible receivers and drivers communicating through a 50P-connector as shown in Figure 11 and Figure 12 "Interface connector". 6.2.1. Signal Specification Figure 8 shows the Signal Specifications N P N Sig.
14/24 SR-C8002 Rev.1.0 6.2.2.Timing of Host Interface (PIO) Figure 9 shows the Host Interface Timings t1 t4 Address valid*1 DIOR-/DIOW-*1 Write data valid*1 t6 t7 Read data valid*1 IOCS16-*1 t8 IORDY tRD t6Z t9 tA tB t2i t3 t5 t0 t2 *1: In all timing diagrams, the low line indicator negated, and the upper line indicators asserted.
15/24 SR-C8002 Rev.1.0 6.2.3.Timing of Host Interface (DMA Multi) Figure 10 shows the Host Interface DMA multi word Timings DMARQ DMACK-*1 DIOR-/DIOW-*1 Read DD0-15 Write DD0-15 tZ tI tJ tD tE tL tF tH tG t0 tK *1: In all timing diagrams, the low line indicator negated, and the upper line indicators asserted.
16/24 SR-C8002 Rev.1.0 6.3. Connector Figure 11 shows the connector and Figure 12 shows the interface pin assignments Use Japan Aviation Electronics Industry Limited KX15-50KLD L or equivalent. Conformable connector is Japan Aviation Electronics Industry Limited KX14-50 series.
17/24 SR-C8002 Rev.1.0 6.4. Support Command List ATAPI Packet Command 00h Test Unit Ready 01h Rezero Unit 03h Request Sense 12h Inquiry 1Bh Start / Stop Unit 1Ch Receive Diagnostics 1Dh Send Diagnosti.
18/24 SR-C8002 Rev.1.0 ATA Command for ATAPI No. OP Code Command Description - 00h Nop 1 08h ATAPI Soft Reset 2 20/21h Read Sector (s) 3 90h Execute Drive Diagnostics 4 A0h ATAPI Packet Command 5 A1h .
19/24 SR-C8002 Rev.1.0 8.CD Audio (Test condition: Ordinary temperature) 8.1. Analog Out --- in case of the attenuator is set at 0 dB by the command --- (1) Output Level 0.8 V (rms)+/-1 dB (2) Type Unbalanced (3) Load Impedance 47 kOHM min (4) Frequency Response 20 Hz to 20 kHz+/-3.
20/24 SR-C8002 Rev.1.0 10. Busy Indicator The LED at Front Bezel (Busy Indicator) indicates the drive status. Color: AMBER (1) After Drawer is closed, Busy Indicator start blinking at 0.8 s intervals, and then ----- (1-1) Turns off when the drive in the 'Idle' status.
21/24 SR-C8002 Rev.1.0 11.Emergency Release Execute following procedure only in the case of emergency (Drawer will not release and disc can not be removed although pressing Release Button). (1) Turn the drive supplying power off. (2) Insert solid bar (like paper clip) into Emergency Release hole and push as shown in Fig.
22/24 SR-C8002 Rev.1.0 13. Electrostatic Discharge Standard IEC61000-4-2 (1) Operating 8 kV or less (2) Damage including 15 kV or more 14. Accessories None 15. Packaging (1) 50 units in a bulk package 24 bulk packs on one pallet. * All transportation is allowed with pallet.
23/24 SR-C8002 Rev.1.0 TOSHIBA TOSHIBA EUROPE GMBH EU-Declaration of Conformity Product: CD-R/RW Drive Manufacturer(s): Toshiba Corporation 1-1, Shibaura 1-chome, Minato-ku, Tokyo 105-8001 Japan See p.
24/24 SR-C8002 Rev.1.0 EU-Declaration of Conformity ED-Directive Related Standard Issude Level/Test condition EMC-emission: EMC-immunity Product/Options Model Related EU-Directive 89/336/EEC X Manufac.
SR-C8002 Rev.1.0 Deviation List Page Item Rev # 0.5 Rev # 1.0 1 2. Features This drive is a new generation..... This drive is a new generation..... .....such as 95 ms access Time. .....such as 120 ms access Time. 2 3.1.Performance (5) Rotational Speed Read: ROM Data Media Approx.
SR-C8002 Rev.1.0 Page Item Rev # 0.5 Rev # 1.0 12 Figure 7 Focus Search TBD Max 2 s Spindle ON TBD Max 3.5 s Stand-by TBD Max 30 s Typ 12 s 6. Interface (1) The interface is based on X3T13/D96153 Revsion 18..... (1) The interface is based on T13/1321D (AT Attachment with Packet Interface-5, (2) 64 (2) 58 17 6.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Toshiba SR-C8002 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Toshiba SR-C8002 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Toshiba SR-C8002 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Toshiba SR-C8002 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Toshiba SR-C8002, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Toshiba SR-C8002.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Toshiba SR-C8002. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Toshiba SR-C8002 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
