Manuale d’uso / di manutenzione del prodotto Bobcat 225G del fabbricante Miller Electric
Vai alla pagina of 26
OWNER’S MANUAL January 1997 Form: OM-175 104B Effective With Serial No. KG191348 cover_om 4/95 – Ref. ST -801 188-A PRINTED IN USA 1997 MILLER Electric Mfg.
OM-175 104B – 1/97 T ABLE OF CONTENTS SECTION 1 – SAFETY PRECAUTIONS FOR ARC WELDING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-175 104 Page 1 SECTION 1 – SAFETY PRECAUTIONS FOR ARC WELDING safety_rom1 4/95 1-1. Symbol Usage Means W arning! W atch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols. This group of symbols means W arning! Watch Out! possible ELECTRIC SHOCK, MOVING P ARTS, and HOT P AR TS hazards.
OM-175 104 Page 2 CYLINDERS can explode if damaged. Shielding gas cylinders contain gas under high pressure. If damaged, a cylinder can explode. Since gas cylinders are normally part of the welding process, be sure to treat them carefully .
OM-175 104 Page 3 1-4. Additional Installation, Operation, And Maintenance Hazards MOVING P ARTS can cause injury . 1. Before working of generator , remove spark plugs or injectors to keep engine from kicking back or starting. 2. Block flywheel so that it will not turn while working on generator components.
OM-175 104 Page 4 SECTION 2 – DEFINITIONS 2-1. Symbol Definitions Stop Engine Fast (Run, W eld/Power) Fast/Slow (Run/Idle) Slow (Idle) Start Engine Read Operator ’s Manual A Amperes V V olts Engin.
OM-175 104 Page 5 SECTION 3 – INST ALLA TION 3-1. Installing Welding Generator install1* 3/96 – Ref. ST -800 652 / Ref. ST -800 477-A / ST -158 936-A / S-0854 1 2 Electrically bond generator frame to vehicle frame by metal-to-metal contact.
OM-175 104 Page 6 3-3. Fuel Consumption Ref. SB-179 939 0.0 0.3 0.5 0.8 1.0 1.3 1.5 1.8 2.0 0 25 50 75 100 125 150 175 200 225 250 275 7.57 6.62 5.67 4.73 3.78 2.84 1.89 0.95 1.67 1.46 1.25 1.04 0.84 0.63 0.42 0.21 LITERS/HR. IMP. GAS/HR. U.S. GAL/HR.
OM-175 104 Page 7 3-5. Connecting The Battery Ref. ST -800 394-B / Ref. ST -178 079-A / Ref. S-0756-D + – 3/8, 1/2 in Connect (–) cable last. T ools Needed: 3-6. W eld Output T erminals And Selecting Cable Sizes ARC WELDING can cause Electromagnetic Interference.
OM-175 104 Page 8 SECTION 4 – OPERA TING WELDING GENERA T OR 4-1. Front Panel Controls Ref. ST -178 079-A 1 Engine Control Switch Use switch to start engine, select speed, and stop engine. In Run/Idle position, en- gine runs at idle speed at no load, and weld/ power speed under load.
OM-175 104 Page 9 4-2. Duty Cycle SB-1 19 454-A Duty cycle is the percentage of 10 minutes that unit can weld at rated load without overheating. Exceeding duty cycle can damage unit and void war- ranty .
OM-175 104 Page 10 SECTION 5 – OPERA TING AUXILIAR Y EQUIPMENT 5-1. Standard Receptacles Ref. ST -178 079-A Auxiliary power decreases as weld current increases. Set Fine Adjust control R1 at 10 for full auxiliary power . 1 120 V 15 A AC Receptacles GFCI-2 And GFCI-3 GFCI-2 and GFCI-3 supply 60 Hz single-phase power at weld/power speed.
OM-175 104 Page 1 1 5-2. Optional Auxiliary Power Receptacles Y If unit does not have GFCI receptacles, use GFCI-pro- tected extension cord. . Auxiliary power decreases as weld current increases. Set Fine Adjust control R1 at 10 for full auxiliary power .
OM-175 104 Page 12 5-3. Wiring Optional 240 V olt Plug ST -120 813-D The plug can be wired for a 240 V , 2-wire load or a 120/240V , 3-wire load. See circuit diagram. 1 Plug Wired For 120/240 V , 3-Wire Load When wired for 120 V loads, each duplex receptacle shares a load with one half of 240 V receptacle.
OM-175 104 Page 13 SECTION 6 – MAINTENANCE AND TROUBLESHOOTING 6-1. Routine Maintenance Recycle engine fluids. Y Stop engine before maintaining. . See also Engine Manual and mainte- nance label. Service engine more often if used in severe conditions.
OM-175 104 Page 14 6-2. Maintenance Label S-173 088 ° C +30 +20 +10 0 -10 -20 -30 ° F KOHLER CH18 GAS ENGINE Check 5W-20, 5W-30 0 +32 10W-30, 10W-40 +100 Recommended Oil API Service Classification SF-SG/CC-CD . . . Oil Change 100 hours . . . . . . .
OM-175 104 Page 15 6-4. Changing Engine Oil, Oil Filter , And Fuel Filter Ref. ST -801 188-A / Ref. ST -801 221 / Ref. ST -178 079-A / ST -800 395 / S-0842 Stop engine and let cool. 1 Oil Drain V alve 2 1/2 ID x 12 in Hose 3 Oil Filter 4 Oil Fill Cap 5 Oil Dipstick Change engine oil and filter ac- cording to engine owner ’ s manual.
OM-175 104 Page 16 6-5. Adjusting Engine Speed Ref. ST -801 188-A / ST -801 209-A After tuning engine, check engine speeds with a tachometer (see table). If necessary , adjust speeds as follows: Start engine and run until warm. T urn Fine Adjust control to 10.
OM-175 104 Page 17 6-6. Overload Protection ST -801 226-A / Ref. ST -801 221 Y Stop engine. 1 Fuse F1 (See Parts List) F1 protects the generator excita- tion circuit. If F1 opens, there will be no/low weld and auxiliary power output. 2 Fuse F6 (See Parts List) F6 protects the engine wiring har- ness.
OM-175 104 Page 18 6-8. T roubleshooting A. Welding T rouble Remedy No weld output. Check control settings. Check weld connections. Check fuse F1 and replace if open (see Section 6-6). Be sure all equipment is disconnected from receptacles when starting unit.
OM-175 104 Page 19 C. Engine T rouble Remedy Engine will not crank. Check fuse F6, and replace if open (see Section 6-6). Check battery voltage. Check battery connections and tighten if necessary . Check plug PLG4 and plug PLG8 connections. Have Factory Authorized Service Agent check Engine Control switch S2.
OM-175 104 Page 20 SECTION 7 – ELECTRICAL DIAGRAM SB-180 690-B Figure 7-1. Circuit Diagram For W elding Generator.
OM-175 104 Page 22 SECTION 8 – P ARTS LIST 1 2 3 45 6 7 8 9 10 14 11 13 15 23 21 34 36 41 42 Fig 8-2 Fig 8-3 Figure 8-1. Main Assembly ST -801 432-B 22 16 17 18 19 20 24 25 26 27 28 29 30 31 32 33 3.
OM-175 104 Page 23 Description Part No. Dia. Mkgs. Item No. Figure 8-1. Main Assembly Quantity 1 +159 907 COVER, top 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-175 104 Page 24 Description Part No. Dia. Mkgs. Item No. Figure 8-2. Panel, Front w/Components (Fig 8-1 Item 44) Quantity 1 S1 162 671 SWITCH, polarity 5 position 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-175 104 Page 25 Description Part No. Item No. Figure 8-3. Generator (Fig 8-1 Item 21) Quantity 1 013 367 LABEL, warning moving parts can cause serious injury 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 165 818 LABEL, warning engine fuel can cause fire 1 .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Miller Electric Bobcat 225G è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Miller Electric Bobcat 225G - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Miller Electric Bobcat 225G imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Miller Electric Bobcat 225G ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Miller Electric Bobcat 225G, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Miller Electric Bobcat 225G.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Miller Electric Bobcat 225G. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Miller Electric Bobcat 225G insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
