Manuale d’uso / di manutenzione del prodotto OM-314 del fabbricante Hobart Welding Products
Vai alla pagina of 28
Cyberstick 250 AC/DC Processes Description Stick (SMA W) W elding Arc Welding Power Source OM-314 029 861V November 1999 .
Hobart W elders manufactures a full line of welders and welding related equipment. For information on other quality Hobart products, contact your local Hobart distributor to receive the latest full line catalog or individual catalog sheets. T o locate your nearest distributor or service agency call 1-877-Hobart1.
The following terms are used interchangeably throughout this manual: TIG = GT AW Stick = SMAW T ABLE OF CONTENTS SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . .
.
OM-314 Page 1 SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING som _nd_4/98 1-1. Symbol Usage Means W arning! W atch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols. Y Marks a special safety message.
OM-314 Page 2 Arc rays from the welding process produce intense visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin. Sparks fly off from the weld. ARC RA YS can burn eyes and skin. D Wear a welding helmet fitted with a proper shade of filter to protect your face and eyes when welding or watching (see ANSI Z49.
OM-314 Page 3 1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. D Do not install or place unit on, over , or near combustible surfaces. D Do not install unit near flammables. D Do not overload building wiring – be sure power supply system is properly sized, rated, and protected to handle this unit.
OM-314 Page 4 1-5. EMF Information Considerations About W elding And The Effects Of Low Frequency Electric A n d M a g netic Fields W elding current, as it flows through welding cables, will cause electro- magnetic fields. There has been and still is some concern about such fields.
OM-314 Page 5 SECTION 1 – CONSIGNES DE SECURITE – LIRE A V ANT UTILISA TION som _nd_fre 4/98 1-1. Signification des symboles Signifie Mise en garde ! Soyez vigilant ! Cette proc é dure pr é sente des risques de danger ! Ceux-ci sont identifi é s par des symboles adjacents aux directives.
OM-314 Page 6 Le rayonnement de l ’ arc du proc é d é de soudage g é n è re des rayons visibles et invisibles intenses (ultraviolets et infrarouges) susceptibles de provoquer des br û lures dans les yeux et sur la peau. Des é tincelles sont projet é es pendant le soudage.
OM-314 Page 7 1-3. Dangers suppl é mentaires en relation avec l ’ installation, le fonctionnement et la maintenance Risque D ’ INCENDIE OU D ’ EXPLOSION. D Ne pas placer l ’ appareil sur , au-dessus ou à proxi- mit é de surfaces infllammables.
OM-314 Page 8 1-4. Principales normes de s é curit é Safety in W elding and Cutting, norme ANSI Z49.1, de l ’ American Wel- ding Society , 550 N.W . Lejeune Rd, Miami FL 33126 Safety and Health Sandards, OSHA 29 CFR 1910, du Superintendent of Documents, U.
OM-314 Page 9 SECTION 2 – INST ALLA TION 2-1. Specifications Model Amperes Input At Rated Load Output, 50 Hz, Single-Phase Amperes Input At Rated Load Output, 60 Hz, Single-Phase Model 220 V 260 V 380 V 440 V 520 V KV A KW 200 V 230 V 460 V 575 V KV A KW AC 68 57.
OM-314 Page 10 2-3. V olt-Ampere Curves ssb1.1 10/91 – SB-002 696-A / SB – 002 689-A The volt-ampere curves show the minimum and maximum voltage an d amperage output capabilities of the welding power source. Curves of other settings fall between the curves shown.
OM-314 Page 1 1 2-5. Selecting A Location 1 Rating Label Use rating label to determine input power needs. Label located on front panel. 2 Line Disconnect Device Locate unit near correct input pow- er supply . Y Special installation may be required where gasoline or volatile liquids are present – see NEC Article 51 1 or CEC Section 20 .
OM-314 Page 12 2-7. Connecting T o W eld Output T erminals ST-800 052-A / Ref. S-161 415 For DC Weld Output 1 Negative ( – ) W eld Output T erminal 2 Positive (+) Weld Output T erminal For Electrode Positive (DCEP), connect work cable to Negative ( – ) terminal and electrode holder cable to Positive (+) terminal.
OM-314 Page 13 2-8. Electrical Service Guide 60 Hertz Models With Power Factor Correction Without Power Factor Correction Input V oltage 200 230 460 575 200 230 460 575 Input Amperes At Rated Output 7.
OM-314 Page 14 2-9. Placing Jumper Links And Connecting Input Power input_3 3/96 - ST-1 1 1 901-F Y Have only qualified persons make this installation. See rating label in Section 2-5, an d be sure to supply correct input power . Check input voltage available at site.
OM-314 Page 15 SECTION 3 – OPERA TION 3-1. Controls ST-186 137 1 Range Selector Switch Us e switch to select ac or dc weld amperage range. If desired amperage is in the overlapping area of two ranges, set switch in the lower range for better fine amperage control.
OM-314 Page 16 SECTION 4 – MAINTENANCE & TROUBLESHOOTING 4-1. Routine Maintenance . Maintain mor e o f t e n during severe conditions. Y Disconnect power before maintaining.
OM-314 Page 17 SECTION 5 – ELECTRICAL DIAGRAMS SB-090 666-D For Primary Circuit Diagram Portion, refer to the Circuit Diagram located inside the wrapper of the welding power source.
OM-314 Page 18 SECTION 6 – P ARTS LIST ST-133 712-G . Hardware is common and not available unless listed. 1 2 3 4 5 6 7 9 8 11 10 6 12 13 FIG 6 – 4 14 15 16 FIG 6 – 2 17 Figure 6-1.
OM-314 Page 19 Replace Coils at Factory or Factory Authorized Service Station Description Quantity Part No. Dia. Mkgs. Item No. Model Without PFC With PFC Figure 6-1. Main Assembly 1 034 288 COVER, top 1 1 . . . . . . . . . . . . . . . . . . . . . . .
OM-314 Page 20 Description Quantity Part No. Dia. Mkgs. Item No. Figure 6-2. Panel, Front w/Components (Fig 6-1 Item 16) 1 NAMEPLA TE, (order by model and serial number) 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-314 Page 21 Description Quantity Part No. Item No. 088 087 Figure 6-3. Switch, Range 2 Position (Fig 6-2 Item 3) 1 072 026 BRACKET , mtg switch 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OM-314 Page 22 Notes.
Warranty Questions? Call 1-877-HOBART1 for your local Hobart distributor. hobart retail 4/00 Service Y o u always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours. Support Need fast answers to the tough welding questions? Contact your distributor or call 1-800-332-3281.
PRINTED IN USA 2000 Hobart Welding Products. 1/00 Hoba rt We lding Produc ts An I l li noi s T ool Works Com pany 600 West Main St reet Troy , O H 45373 US A For Technical A ssistan ce: Call1-800-.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hobart Welding Products OM-314 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hobart Welding Products OM-314 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hobart Welding Products OM-314 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hobart Welding Products OM-314 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hobart Welding Products OM-314, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hobart Welding Products OM-314.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hobart Welding Products OM-314. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hobart Welding Products OM-314 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
