IT
Skil logo
Manuale d'uso ufficiale

Skil 9955

144 pagine·7.4 MB·Varie·PDF·ENJA
Skil 9955
Indice dei contenuti 15 sezioni POLISHER 9955 (F0159955..) · ПОДЛИННИК РУКОВОДСТВА · Polisher 9955 · INTRODUCTION · … MostraNascondi
Page 1 of the Skil 9955 user manual —  ПОДЛИННИК РУКОВОДСТВА
Pagina 1 · clicca per ingrandire
Pagina 1

POLISHER 9955 (F0159955..)

Skil 9955 — POLISHER 9955 (F0159955..) diagram (page 1)
Fig. 1

ПОДЛИННИК РУКОВОДСТВА

SKIL Europe BV - Konijnenberg 60 04/16 2610Z05326 4825 BD Breda - The Netherlands

Page 2 of the Skil 9955 user manual — POLISHER 9955 (F0159955..)
Pagina 2 · clicca per ingrandire
Pagina 2
Skil 9955 — POLISHER 9955 (F0159955..) diagram (page 2)
Fig. 2
Skil 9955 — POLISHER 9955 (F0159955..) diagram (page 2)
Fig. 3
Skil 9955 — POLISHER 9955 (F0159955..) diagram (page 2)
Fig. 4
Skil 9955 — POLISHER 9955 (F0159955..) diagram (page 2)
Fig. 5
Page 3 of the Skil 9955 user manual — POLISHER 9955 (F0159955..)
Pagina 3 · clicca per ingrandire
Pagina 3
Skil 9955 — POLISHER 9955 (F0159955..) diagram (page 3)
Fig. 6
Skil 9955 — POLISHER 9955 (F0159955..) diagram (page 3)
Fig. 7
Skil 9955 — POLISHER 9955 (F0159955..) diagram (page 3)
Fig. 8
Page 4 of the Skil 9955 user manual — GENERAL SAFETY INSTRUCTIONS
Pagina 4 · clicca per ingrandire
Pagina 4

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an

Polisher 9955

INTRODUCTION

  • This tool is intended for polishing metal, plastic and coated surfaces as well as for the polishing of stone materials without the use of water
  • Read and save this instruction manual 2

extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is

unavoidable, use an earth leakage circuit breaker. Use of an earth leakage circuit breaker reduces the risk of electric shock. 3) PERSONAL SAFETY a) Stay alert, watch what you are doing and use

TECHNICAL DATA 1

TOOL ELEMENTS 3

A Auxiliary handle B Auxiliary handle (type D) C Hex key D Spindle E Backing pad (VELCRO) F Spindle-lock button G Wool bonnet H On/off switch J Knob for locking on/off switch K Wheel for maximum speed control L Ventilation slots

common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is

in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning

SAFETY

GENERAL SAFETY INSTRUCTIONS

the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or

1. WORK AREA SAFETY a) Keep work area clean and well lit. Cluttered or dark

jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. g) If devices are provided for the connection of dust

areas invite accidents. b) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating

extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. 4) POWER TOOL USE AND CARE a) Do not force the power tool. Use the correct power

a power tool. Distractions can cause you to lose control. 2) ELECTRICAL SAFETY a) Power tool plugs must match the outlet. Never

tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn

modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded

it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or

surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions.

the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children

Water entering a power tool will increase the risk of electric shock.

and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.

Page 5 of the Skil 9955 user manual — SAFETY INSTRUCTIONS FOR POLISHERS
Pagina 5 · clicca per ingrandire
Pagina 5

Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or

inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no load speed for one minute. Damaged accessories will normally break apart during this test time. i) Wear personal protective equipment 4. Depending

binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly

on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and shop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying debris generated by various operations. The dust mask or respirator must be capable of filtrating particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss. j) Keep bystanders a safe distance away from work

maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

area. Anyone entering the work area must wear personal protective equipment. Fragments of the workpiece or of a broken accessory may fly away and cause injury beyond the immediate area of operation. k) Position the cord clear of the spinning accessory. If

SAFETY INSTRUCTIONS FOR POLISHERS

1. SAFETY INSTRUCTIONS FOR ALL OPERATIONS a) This power tool is intended to function as a

you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory. l) Never lay the power tool down until the accessory

polisher. Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. b) This power tool is not recommended for grinding,

has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control. m) Do not run the power tool while carrying it at your

sanding, wire brushing or cutting off operations. Operations for which the power tool was not designed may create a hazard and cause personal injury. c) Do not allow any loose portion of the polishing

side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body. n) Regularly clean the power tool’s air vents. The

bonnet or its attachment strings to spin freely. Tuck away or trim any loose attachment strings. Loose and spinning attachment strings can entangle your fingers or snag on the workpiece. d) Do not use accessories which are not specifically

motor’s fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards. o) Do not operate the power tool near flammable

designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation. e) The rated speed of the accessory must be at least

materials. Sparks could ignite these materials. p) Do not use accessories that require liquid coolants.

  • Using water or other liquid coolants may result in electrocution or shock. 2) KICKBACK AND RELATED WARNINGS
  • Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory’s rotation at the point of the binding.
  • For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the pinch point can dig into the surface of the material causing the wheel to climb out or kick out. The wheel may either jump toward or away from the operator, depending on the direction of the wheel’s movement at the point of pinching. Abrasive wheels may also break under these conditions.
  • Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.

equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can fly apart. f) The outside diameter and the thickness of your

accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled. g) Threaded mounting of accessories must match the

grinder spindle thread. For accessories mounted by flanges, the arbour hole of the accessory must fit the locating diameter of the flange. Accessories that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control. h) Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for chips and cracks, backing pads for cracks, tear or excess wear, wire brushes for loose or cracked wires. If the power tool or accessory is dropped,

Page 6 of the Skil 9955 user manual — USE
Pagina 6 · clicca per ingrandire
Pagina 6

a) Maintain a firm grip on the power tool and position

  • Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in conjunction with additives for wood conditioning; wear a dust mask and work with a dust extraction device when connectable
  • Follow the dust-related national requirements for the materials you want to work with
  • Secure the workpiece (a workpiece clamped with clamping devices or in a vice is held more securely than by hand)
  • Do not clamp the tool in a vice
  • Use completely unrolled and safe extension cords with a capacity of 16 Amps (U.K. 13 Amps) DURING USE
  • When working, always hold the tool firmly with both hands and take a secure stance
  • Always keep the cord away from moving parts of the tool; direct the cord to the rear, away from the tool
  • If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug
  • Never use the tool when cord is damaged; have it replaced by a qualified person
  • In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug
  • In case of current interruption or when the plug is accidentally pulled out, release switch H 3 in order to prevent uncontrolled restarting AFTER USE
  • Before you put down the tool, switch off the motor and ensure that all moving parts have come to a complete standstill
  • After switching off the tool, never stop the rotation of the accessory by a lateral force applied against it WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
  • Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug
  • If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended

your body and arm to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up. The operator can control torque reactions or kickback forces, if proper precautions are taken. b) Never place your hand near the rotating accessory.

The accessory may kickback over your hand. c) Do not position your body in the area where power

tool will move if kickback occurs. Kickback will propel the tool in the direction opposite to the wheel’s movement at the point of snagging. d) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback. e) Do not attach a saw chain woodcarving blade or

toothed saw blade. Such blades create frequent kickback and loss of control.

  • GENERAL
  • Only use this tool for dry polishing
  • Only use the flanges which are supplied with this tool
  • This tool should not be used by people under the age of 16 years
  • Always disconnect plug from power source before making any adjustment or changing any accessory
  • Do not work materials containing asbestos (asbestos is considered carcinogenic) ACCESSORIES
  • SKIL can assure flawless functioning of the tool only when the correct accessories are used which can be obtained from your SKIL dealer
  • For mounting/using non-SKIL accessories observe the instructions of the manufacturer concerned
  • Use only accessories with an allowable speed matching at least the highest no-load speed of the tool
  • Never use accessories with a “blind” threaded hole smaller than M14 x 21 mm
  • Do not use damaged, deformed or vibrating accessories OUTDOOR USE
  • When used outdoors, connect the tool via a fault current (FI) circuit breaker with a triggering current of 30 mA maximum, and only use an extension cord which is intended for outdoor use and equipped with a splashproof coupling-socket BEFORE USE
  • Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply)
  • Always mount auxiliary handle A 3 or B 3 ; never use the tool without it
  • Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful (contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders); wear a dust mask and work with a dust extraction device when connectable

USE

  • Mounting of auxiliary handles 5 ! disconnect the plug - screw auxiliary handle A on the right or the left of the

tool (depending on the work to be carried out) - mount auxiliary handle B as illustrated and tighten

both screws supplied with hex key C • Mounting of accessories 3 ! disconnect the plug - clean spindle D and all parts to be mounted - screw VELCRO backing pad E onto spindle D while

pushing spindle-lock button F ! push spindle-lock button F only when spindle D is

at a standstill - simply press wool bonnet G onto VELCRO backing

pad E - for removing accessories handle vice-versa • Before using the tool - ensure that accessory is correctly mounted and firmly

tightened - check if accessory runs freely by turning it by hand

Page 7 of the Skil 9955 user manual — MAINTENANCE / SERVICE
Pagina 7 · clicca per ingrandire
Pagina 7

ENVIRONMENT

- test-run tool for at least 30 seconds at highest no-load

speed in a safe position - stop immediately in case of considerable vibration or

  • Do not dispose of electric tools, accessories and packaging together with household waste material (only for EU countries) - in observance of European Directive 2012/19/EC on
  • other defects and check tool to determine the cause
  • On/off - switch on/off the tool by pulling/releasing trigger H 3
  • Electronic soft-start Ensures reaching the maximum speed smoothly without a sudden impact when tool is switched on
  • Switch locking for continuous use - pull trigger H - press knob J with your thumb - unlock the switch by pulling again trigger H and then

waste of electric and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility - symbol 8 will remind you of this when the need for

releasing it • Speed control 6 - with wheel K the maximum speed can be adjusted

DECLARATION OF CONFORMITY

  • We declare under our sole responsibility that the product described under “Technical data” is in conformity with the following standards or standardization documents: EN 60745, EN 61000, EN 55014, in accordance with the provisions of the directives 2004/108/EC, 2006/42/EC, 2011/65/EU
  • Technical file at : SKIL Europe BV (PT-SEU/ENG1), 4825 BD Breda, NL

from low to high (1-MAX) - start with wheel K in position 1 (lower speed) - if needed, select a higher speed while the tool runs - the optimal working speed depends on the material

and can be determined with practical trials • Operating the tool - switch on the tool - place the tool fully on the surface to be polished and

¹ÊÁÂÆÎ¹Æ¼½Ê ÇǾ¼½Æ ȽʹÌÁÇÆËŵ Æ¿Áƽ½ÊÁÆ¿

Ĺ¾ ÁÂÿʹ¹¾ ÈÈÊÇιĹƹ¿½Ê

move it evenly by sections - one move should overlap the previous move by one

half - do not stop at a single spot to avoid burning the

coating - do not move the tool in circles to avoid staining or

burning the coating ! before switching off the tool, you should lift it

ÍÊÇȽƓˁ˅ʿ˂ ʽ¼¹Ɠ

27.01.2014

from the workpiece ! the accessory continues to rotate for a short time

  • NOISE/VIBRATION
  • Measured in accordance with EN 60745 the sound pressure level of this tool is 86 dB(A) and the sound power level 97 dB(A) (standard deviation: 3 dB), and the vibration 8.5 m/s² (hand-arm method; uncertainty K = 1.5 m/s²)
  • The vibration emission level has been measured in accordance with a standardised test given in EN 60745; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned - using the tool for different applications, or with different

after the tool has been switched off • Holding and guiding the tool 7 ! while working, always hold the tool at the

grey-coloured grip area(s) - always hold the tool firmly with both hands, so you will

have full control of the tool at all times - provide for a secure stance ! do not apply so much pressure on the tool that it

comes to a standstill - keep ventilation slots L 3 uncovered

MAINTENANCE / SERVICE

or poorly maintained accessories, may significantly increase the exposure level - the times when the tool is switched off or when it is

  • Protect the tool from impact, shock and grease
  • Always keep tool and cord clean (especially ventilation slots L 3 ) ! disconnect the plug before cleaning ! do not attempt to clean ventilation slots by

running but not actually doing the job, may significantly reduce the exposure level ! protect yourself against the effects of vibration

by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns

inserting pointed objects through openings • If the tool should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for SKIL power tools - send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service station (addresses as well as the service diagram of the tool are listed on www.skilmasters.com)

disposing occurs

Fai una domanda su Skil 9955

I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Nessuna domanda ancora per il dispositivo Skil 9955

Invia la prima domanda: risponderanno altri possessori o il nostro team.

Documento originale

Skil 9955 manuale in PDF

144 pagine·7.4 MB·Varie·PDF
Clicca su qualsiasi pagina in alto per aprirla qui
Pagina 1 / …
100%
Caricamento pagine…