IT
Skil logo
Manuale d'uso ufficiale

Skil 7720

108 pagine·6.5 MB·Varie·PDF·ENJA
Skil 7720
Indice dei contenuti 17 sezioni Scraper 7720 · INTRODUCTION · TECHNICAL DATA 1 · TOOL ELEMENTS 3 · … MostraNascondi
Page 1 of the Skil 7720 user manual
Pagina 1 · clicca per ingrandire
Pagina 1
Skil 7720 diagram (page 1)
Fig. 1

SKIL Europe BV - Konijnenberg 60 12/13 2610Z05306 4825 BD Breda - The Netherlands

Page 2 of the Skil 7720 user manual
Pagina 2 · clicca per ingrandire
Pagina 2
Skil 7720 diagram (page 2)
Fig. 2
Skil 7720 diagram (page 2)
Fig. 3
Skil 7720 diagram (page 2)
Fig. 4
Page 3 of the Skil 7720 user manual
Pagina 3 · clicca per ingrandire
Pagina 3
Skil 7720 diagram (page 3)
Fig. 5
Page 4 of the Skil 7720 user manual
Pagina 4 · clicca per ingrandire
Pagina 4
Skil 7720 diagram (page 4)
Fig. 6
Page 5 of the Skil 7720 user manual — GENERAL SAFETY INSTRUCTIONS
Pagina 5 · clicca per ingrandire
Pagina 5

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an

Scraper 7720

INTRODUCTION

  • This tool is intended for the fragmentary removal/scraping off of coverings and the remains of adhesives and filler material, for the smoothing of irregularities, and for carving work in soft wood
  • Read and save this instruction manual 2

extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is

unavoidable, use an earth leakage circuit breaker. Use of an earth leakage circuit breaker reduces the risk of electric shock. 3) PERSONAL SAFETY a) Stay alert, watch what you are doing and use

TECHNICAL DATA 1

common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear

TOOL ELEMENTS 3

A Switch for on/off and speed control B Indicator of selected speed C Switch for locking accessories D Indicator of lock position E Accessory holder F Ventilation slots G Wide (60 mm) steel blade - extra sharp H Wide (60 mm) steel spatula J Narrow (15 mm) flat steel chisel K Narrow (35 mm) steel universal blade - extra sharp

eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is

in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning

SAFETY

GENERAL SAFETY INSTRUCTIONS

the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or

jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. g) If devices are provided for the connection of dust

1. WORK AREA SAFETY a) Keep work area clean and well lit. Cluttered or dark

areas invite accidents. b) Do not operate power tools in explosive

extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. 4) POWER TOOL USE AND CARE a) Do not force the power tool. Use the correct power

atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating

tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn

a power tool. Distractions can cause you to lose control. 2) ELECTRICAL SAFETY a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded

it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or

the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children

surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions.

and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

Water entering a power tool will increase the risk of electric shock.

Page 6 of the Skil 7720 user manual — USE
Pagina 6 · clicca per ingrandire
Pagina 6

e) Maintain power tools. Check for misalignment or

  • penetrating a water pipe will cause property damage or an electrical shock)
  • Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful (contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders); wear a dust mask and work with a dust extraction device when connectable
  • Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in conjunction with additives for wood conditioning; wear a dust mask and work with a dust extraction device when connectable
  • Follow the dust-related national requirements for the materials you want to work with
  • This tool should not be used by people under the age of 16 years
  • SKIL can assure flawless functioning of the tool only when the correct accessories are used which can be obtained from your SKIL dealer
  • Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
  • Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug
  • If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended

binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR SCRAPERS

  • Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply)
  • If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug
  • Never use the tool when cord is damaged; have it replaced by a qualified person
  • When used outdoors, connect the tool via a fault current (FI) circuit breaker with a triggering current of 30 mA maximum, and only use an extension cord which is intended for outdoor use and equipped with a splashproof coupling-socket
  • Always keep the cord away from moving parts of the tool; direct the cord to the rear, away from the tool
  • Pay attention to the risk of injury caused by material particles that splinter off and fly about; wear safety glasses and protective gloves
  • Never place your hands in front of the immediate working area
  • Keep other persons out of the working area while working
  • Secure the workpiece (a workpiece clamped with clamping devices or in a vice is held more securely than by hand)
  • Do not work with moistened materials (such as wallpaper) or in damp areas
  • Do not soak the work area with solvents (while scraping, poisonous vapours could be produced as a result of the warming up of the worked material)
  • Do not work materials containing asbestos (asbestos is considered carcinogenic)
  • Hold the power tool only by the insulated gripping surfaces when performing an operation where the accessory may contact hidden wiring or its own power cord (contact with a “live” wire will also make exposed metal parts of the power tool “live” and shock the operator)
  • Use suitable detectors to find hidden utility lines or call the local utility company for assistance (contact with electric lines can lead to fire or electrical shock; damaging a gas line can result in an explosion;

USE

  • Mounting of accessories 4 ! wear protective gloves - slide switch C backward to unlock accessory holder E - slide the accessory (with the working edge pointing

downward) to full depth into accessory holder E - slide switch C forward to lock accessory holder E - clean the accessory shaft after each replacement • On/off - switch on the tool by pushing switch A 3 forward - switch off the tool by pushing switch A 3 backwards

(position 0) • Speed control 5 - select working speed by sliding switch A into desired

position 1 = low speed for precision work 2 = medium speed 3 = high speed for quick removal of material - the optimal working speed depends on the material

and can be determined with practical trials • Operating the tool ! wear protective gloves and use safety glasses - mount desired accessory - switch on the tool - advance the tool to the material/location to be scraped - start with a flat angle and light pressure - work away from the body - be aware that the stroke motion of the tool is only

produced when pressure is applied to the material to be removed - be aware that too much pressure may cause damage

to the background material ! do not overload the tool ! allow tool and accessory to cool down between

the individual work steps

Page 7 of the Skil 7720 user manual — CARACTERISTIQUES TECHNIQUES 1
Pagina 7 · clicca per ingrandire
Pagina 7
  • Sharpening of accessories - with sharp accessories, good working performance

DECLARATION OF CONFORMITY

and a long service life can be achieved - sharpen the steel accessories before they come dull

  • We declare under our sole responsibility that the product described under “Technical data” is in conformity with the following standards or standardization documents: EN 60745, EN 61000, EN 55014, in accordance with the provisions of the directives 2004/108/EC, 2006/42/EC, 2011/65/EU
  • Technical file at : SKIL Europe BV (PT-SEU/ENG1), 4825 BD Breda, NL

APPLICATION ADVICE

  • Use accessory G for working on hard materials 6 ! soft materials (such as wood and aluminium) can

be easily damaged with extra sharp blades Possible applications are: - removal of carpet adhesive and foam-, plaster-,

¹ÊÁÂÆÎ¹Æ¼½Ê ÇǾ¼½Æ ȽʹÌÁÇÆËŵ Æ¿Áƽ½ÊÁÆ¿

Ĺ¾ ÁÂÿʹ¹¾ ÈÈÊÇιĹƹ¿½Ê

mortar- remains as well as remains of joint material - smoothing of unevennesses - removal of floor coverings ! hold the tool firmly with both hands and take a

secure stance • Use accessory H for working on soft materials 7 Possible applications are: - removal of paint residue, silicon and plaster as well as

ÍÊÇȽƓˁ˅ʿ˂ ʽ¼¹Ɠ

23.12.2013

stucco from glass and plastic panels - smoothing and removing of adhesive and sealing

  • NOISE/VIBRATION
  • Measured in accordance with EN 60745 the sound pressure level of this tool is 81 dB(A) and the sound power level 92 dB(A) (standard deviation: 3 dB), and the vibration 12.7 m/s² (hand-arm method; uncertainty K = 1.5 m/s²)
  • The vibration emission level has been measured in accordance with a standardised test given in EN 60745; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned - using the tool for different applications, or with different

residues from wooden flooring • Use accessory J for carving work 8 - carving is possible only in wood with short fibres (such

as linden and poplar) ! hold the tool firmly with both hands and take a

secure stance • Use accessory K for removing sealing from window joints or remains from door rabets 9

MAINTENANCE / SERVICE

  • Always keep tool and cord clean (especially ventilation slots F 3 ) - clean the tool with a dry, soft cloth (do not use cleaning

or poorly maintained accessories, may significantly increase the exposure level - the times when the tool is switched off or when it is

  • agents or solvents) ! disconnect the plug before cleaning
  • Keep tool as well as accessories free from adhesives or any other residuary material
  • Always store the tool indoors in its protective carton/case
  • If the tool should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for SKIL power tools - send the tool undismantled together with proof of

running but not actually doing the job, may significantly reduce the exposure level ! protect yourself against the effects of vibration

by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns

Grattoir 7720

purchase to your dealer or the nearest SKIL service station (addresses as well as the service diagram of the tool are listed on www.skilmasters.com)

INTRODUCTION

  • Cet outil est conçu pour ôter/gratter les éléments détritiques des revêtements ainsi que les résidus de colles et de matériaux de remplissage, pour lisser les irrégularités et pour des travaux de creusement dans du bois tendre
  • Lisez et conservez ce manuel d’instruction 2

ENVIRONMENT

  • Do not dispose of electric tools, accessories and packaging together with household waste material (only for EU countries) - in observance of European Directive 2012/19/EC on

waste of electric and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility - symbol 0 will remind you of this when the need for

CARACTERISTIQUES TECHNIQUES 1

ELEMENTS DE L’OUTIL 3

A Interrupteur de marche/arrêt et réglage de vitesse B Indicateur de la vitesse sélectionnée C Interrupteur pour verrouiller les accessoires

disposing occurs

Fai una domanda su Skil 7720

I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Nessuna domanda ancora per il dispositivo Skil 7720

Invia la prima domanda: risponderanno altri possessori o il nostro team.

Documento originale

Skil 7720 manuale in PDF

108 pagine·6.5 MB·Varie·PDF
Clicca su qualsiasi pagina in alto per aprirla qui
Pagina 1 / …
100%
Caricamento pagine…