Manuale d’uso / di manutenzione del prodotto 3742 del fabbricante Zebra Technologies
Vai alla pagina of 30
User’s Manual No. 980344-001 Rev. A ©2001 Zebra Technologies Corporation 2722 2742 3742 Desktop Thermal Printer User’s Manual.
COPYRIGHT NOTICE This document contains information proprietary to Zebra Technologies Corporation. This docu - ment and the information contained within is copyrighted by Zebra Technologies Corporation and may not be duplicated in full or in part by any person without written approval from Zebra Technol - ogies Corporation.
TABLE OF CONTENTS Installation and Operation Unpacking Your Printer . . . . . . . . . . . . . . . . . . . . 2 Getting To Know Your Printer . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Attach Power .
General Cautions and Warnings This page describes general safety and maintenance warnings and cautions for the printer and are referenced throughout the manual. Warning - Shock Hazard The printer should never be operated in a location where it can get wet.
1 Installation and Operation This section provides information on the instal- lation and operation of the printer. The printer is a low cost, desktop thermal bar code printer. LP models are direct thermal. TLP modes are thermal transfer and direct thermal printers.
Unpacking Your Printer Installation and Operation 2 980344-001 Rev.A For W in B a r C o d e L a b e l P r in t e r s S o ftw a re a n d D o c u m e n ta tio n 105551 -006 © 2001 Zeb ra T echno log ie.
Getting To Know Your Printer 980344-001 Rev.A 3 Installation and Operation.
Installation The following steps will guide you through the installation of the printer, media and software. Step 1 - Attach Power SHOCK HAZARD WARNING See page iv Installation and Operation 4 980344-001 Rev.
Step 2 - Attach Interface Cable 980344-001 Rev.A 5 Installation and Operation Parallel Interface Serial Interface.
Step 3 - Load Media Installation and Operation 6 980344-001 Rev.A Open Cover Open Print Head Open Guides MOVIE MOVIE MOVIE.
Before You Load Media in the Printer You must remove the outside length of media (that is, one, full revolution of labels and any liner). When you remove this part of the media, you remove the oils, dust, and adhesives that contaminate it.
Step 3 - Load Media (cont.) Installation and Operation 8 980344-001 Rev.A 2722 Install Roll Media OUT OUT OUT OUT OUT OUT OUT OUT 2742 / 3742 Install Roll MOVIE.
Step 3 - Load Media (cont.) 980344-001 Rev.A 9 Installation and Operation Thread the Media MOVIE MOVIE Seat Media Roll.
Step 3 - Load Media (cont.) Installation and Operation 10 980344-001 Rev.A Close Guides Close Guides 2742 / 3742 MOVIE.
Step 3 - Load Media (cont.) 980344-001 Rev.A 11 Installation and Operation Close Cover MOVIE MOVIE Close Print Head.
Step 3 - Load Media (cont.) If the indicator fails to light, refer to Appendix A - Trouble Shooting. Run the AutoSense routine. Installation and Operation 12 980344-001 Rev.
Step 4 - AutoSense Step 5 - Install Software Start your computer and follow the installation instructions on the compact disc (CD). 980344-001 Rev.A 13 Installation and Operation O O 2 UKQ1813 4.00 Serial port : 96,N,8,1 Image buffer size:245K Fmem:000,0K,019.
Using Fan-Fold Media Installation and Operation 14 980344-001 Rev.A Place Media In Rear Face Print Surface UP Insert & Load Media.
Label Dispenser Printers with an optional label taken sensor can dispense a single peeled label. Remove the label to automatically print the next label.
Label Dispense Option Installation and Operation 16 980344-001 Rev.A TLP2722 Insert Liner (2742 Shown) Pull Liner Through (2742 Shown).
Label Dispense Option 980344-001 Rev.A 17 Installation and Operation Close Print Head Close Cover TL P 2722 Push to Open Label Taken Sensor Press FEED Button TLP2722 Remove Presented Label.
Thermal Transfer Ribbon Loading This feature is supported on TLP model printers, only. Installation and Operation 18 980344-001 Rev.A Thermal Transfer Print Head Mechanism MOVIE Ribbon Path.
Thermal Transfer Ribbon Loading Open Print Head 980344-001 Rev.A 19 Installation and Operation Load Ribbon Core Load Transfer Ribbon Start Ribbon Open Print Head (Rear View) Pull Ribbon Around Print H.
Installation and Operation 20 980344-001 Rev.A.
Appendix A - Troubleshooting Problem Solution or Reason POWER indicator does not light GREEN when power switch is turned to ON (1) position. 1. Check power connections from A.C. outlet to power supply to printer. POWER indicator lights GREEN, but printer will not print.
Printer Maintenance 22 980344-001 Rev.A Clean the Print Head Don’t Clean Rollers with Cleaning Pen MOVIE.
Printer Configuration Settings The printer has flash (non-volatile) memory to store printer configuration settings. The settings are stored in flash memory and are set by programing, printer drivers or the AutoSense routine. The settings are shown on the Dump mode printout or can be reported back to the host via the serial port.
Serial Interface Communication Configuration The printer’s serial port is configured with the Y command for the printer. The printer supports interface data rates from 1200 to 38,400 baud.
Parallel Interface Cable Wiring The figure below displays the cable wiring required to use the printer's Centronics parallel interface. +5 volts at 300 mA for external device (e.g. PrintServer) 980344-001 Rev.A 25 PRINTER DB -25 Pin No. Centronics Pin No.
26 980344-001 Rev.A.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Zebra Technologies 3742 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Zebra Technologies 3742 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Zebra Technologies 3742 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Zebra Technologies 3742 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Zebra Technologies 3742, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Zebra Technologies 3742.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Zebra Technologies 3742. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Zebra Technologies 3742 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
