Manuale d’uso / di manutenzione del prodotto ZT400 del fabbricante Zebra Technologies
Vai alla pagina of 15
© 2014 ZIH Corp. All product names and numbers are Zebra trademarks, and Zebra and th e Zebra logo are registered trademarks of ZIH Corp. All right s reserved. P1060608-003 4/8/14 ZT400™ Series Quick Reference Guide Use this guide to operate your pr inter on a dail y basis.
Control Panel 2 P1060608-003 ZT400™ Series Quick Reference Guide 4/8/14 Control Panel The control panel ( Figure 2 ) indicates the printer’ s current statu s and allows the user to co ntrol basic printer operation.
3 Prep aring the Printer for Use 4/8/14 ZT400™ Series Quick Reference Guide P1060608-003 Prep aring the Printer for Use After you have familiariz ed yourself with the printer components, prep are the printer for use . T o set up the printer , complete these step s: 1.
Preparing the Printer for Use 4 P1060608-003 ZT400™ Series Quick Reference Guide 4/8/14 5. Plug the male end of the A/ C power co rd int o an appropri ate power outl et. 6. Connect the printer to a comp uter using one or more of the avai lable connections.
5 Prep aring the Printer for Use 4/8/14 ZT400™ Series Quick Reference Guide P1060608-003 7. Raise the media door . 8. Load ribbon (if using Thermal T ransfer mode) and media into the printer (se e Load Medi a and Ribbon on page 8 ). 9. Close the media door .
Preparing the Printer for Use 6 P1060608-003 ZT400™ Series Quick Reference Guide 4/8/14 10. T o verify that the media and ribbon are load ed correctl y , print a p rinter configuration label. a. Press and hold the CANCEL button. b. T urn on ( I ) the printer .
7 Prep aring the Printer for Use 4/8/14 ZT400™ Series Quick Reference Guide P1060608-003 11 . T o test the connection betwee n your printer an d your computer , use a label design package to create a sample label and send it to the prin ter . Zebra recommend s ZebraDesigner Pro.
Load Media and Ribbon 8 P1060608-003 ZT400™ Series Quick Reference Guide 4/8/14 Load Media and Ribbon Use the instructions i n this section to load ri bbon (if used) and med ia in T ear-Of f mode. Ribbon is used with th ermal transfer labels. For direct the rmal labels, do not load ribbon in the printer.
9 Load Media an d Ribbon 4/8/14 ZT400™ Series Quick Reference Guide P1060608-003 2. Remove and discard any tags or labels that are dirty or that are held by adhesives or tape. 3. Pull out the media supply guide as far as it goes. 4. Place the roll of media on the media supply ha nger .
Load Media and Ribbon 10 P1060608-003 ZT400™ Series Quick Reference Guide 4/8/14 5. Slide in the media supply gu ide until it touch es the edge of the roll.
11 Load Media an d Ribbon 4/8/14 ZT400™ Series Quick Reference Guide P1060608-003 7. From the media hanger ( 1 ), feed the media under the dancer assembly ( 2 ), through the media sensor ( 3 ), and under the pri nthead assembly ( 4 ). Slide the media back unt il it touches the inside back wall of t he media sensor .
Load Media and Ribbon 12 P1060608-003 ZT400™ Series Quick Reference Guide 4/8/14 9. Which type of me dia did you l oad into the printer? 10. Push down the printh ead assembly ( 1 ), and then rotate the prin thead-open lever ( 2 ) u ntil it locks into plac e.
13 Load Media an d Ribbon 4/8/14 ZT400™ Series Quick Reference Guide P1060608-003 13. Place the roll of ri bbon on the r ibbon supply sp indle. Push the r oll back as far as it will g o. 14. Slide the ribbon under the printhead assembly , and then wrap it several turns around the ribbon ta ke-up spindle.
Load Media and Ribbon 14 P1060608-003 ZT400™ Series Quick Reference Guide 4/8/14 15. Push down the printh ead assembly ( 1 ), and then rotate the prin thead-open lever ( 2 ) u ntil it locks into plac e. 16. If necessary , press PA U S E to clear any errors and enable printing.
15 Load Media an d Ribbon 4/8/14 ZT400™ Series Quick Reference Guide P1060608-003 Remove Used Ribbon Remove used ribbon from the ribbon take -up spindle e ach time you ch ange the roll o f ribbon. T o remove used ribbon, complete these step s: 1. Has the ribb on run out? 2.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Zebra Technologies ZT400 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Zebra Technologies ZT400 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Zebra Technologies ZT400 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Zebra Technologies ZT400 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Zebra Technologies ZT400, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Zebra Technologies ZT400.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Zebra Technologies ZT400. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Zebra Technologies ZT400 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
