Manuale d’uso / di manutenzione del prodotto 2844 Printer del fabbricante Zebra Technologies
Vai alla pagina of 36
User’s Manual No. 980348-001 Rev. A ©2001 Zebra Technologies Corporation 2844 Thermal Printer User’s Manual.
FOREWORD This manual provides installation and operation information for the LP 2844 and the TLP 2844 series printers, manufactured by Zebra Technologies Corporation, Camarillo, California. COPYRIGHT NOTICE This document contains information proprietary to Zebra Technologies Corporation.
SHOCK HAZARD WARNING: The printer and power supply should never be operated in a location where either one can get wet. Personal injury could result. MEDIA AND RIBBON WARNING: Always use high quality, approved labels, tags and ribbons.
980348-001 Rev. A v TABLE OF CONTENTS Installation and Operation . . . . . . . . . . . . . . . . . . 1 Unpack Your Printer . . . . . . . . . . . . . . . . . . . . . . 2 Know Your Printer . . . . . . . . . . . . . . . . . . . . . . . 2 Installation . .
1 Installation and Operation This section provides information on the installation and operation of the printer. The printer is a low cost, desktop thermal printer. The printer is specifically designed for printing labels, tags or continuous receipts (with or without bar codes) from any DOS™, Win- dows™or ASCII-based compatible host.
Unpack Your Printer Know Your Printer 2 980348-001 Rev. A Installation and Operation.
980348-001 Rev. A 3 Installation and Operation.
Installation The following steps will guide you through the installation of the printer and software. Step ➊ Attach Power Supply To The Printer See the SHOCK HAZARD WARNING on page iv.
Step ➋ Attach Interface Cable See Appendix A for cable wiring information. 980348-001 Rev. A 5 Installation and Operation Parallel Serial Universal Serial Bus (USB).
Step ➌ Load Media 6 980348-001 Rev. A Installation and Operation Power ON Open Cover Open Guides MO VIE.
Load Media - continued 980348-001 Rev. A 7 Installation and Operation Remove the outside length of media For more infor - mation on media preparation, refer to Appendix A. MO VIE Install Roll Note: Find the instructions for preparing media in Appendix A.
Load Media - continued 8 980348-001 Rev. A Installation and Operation MO VIE Release Cover Note: This step applies to thermal transfer printers Close Cover.
Step AutoSense Media Gap Sensing Perform this procedure when loading a new roll. If your printer has the label dispenser option, turn OFF the label taken sensor.
AutoSense Gap Sensor Adjustment - continued If the indicator remains orange or red, see the troubleshooting steps. 10 980348-001 Rev. A Installation and Operation When Indicator Flashes, Release Feed Button UKQ1935 16 V3.21 Serial port : 96,N,8,1 Image buffer size:1032K Fmem:000.
Step ➎ Install Software Start your computer and follow the installation instructions on the compact disc (CD). 980348-001 Rev. A 11 Installation and Operation.
Operation The following information helps you get the most from your printer. Programming Commands You must use programming to control many of the printer's functions. See the EPL2 program - mer's manual for details. For example, the Q command controls form length and gap.
2 Using Options This section provides information on the printer's optional features: • thermal transfer printing • label dispenser • fan-fold media • media cutter 980348-001 Rev.
Using Transfer Ribbon The TLP printer supports both direct thermal media (chemically treated to darken when heated) and thermal transfer media (accepts wax and/or resin transferred off a ribbon).
Step ➋ Install Supply Roll 980348-001 Rev. A 15 Using Options Press onto Hub Thread Ribbon Through Carriage Align Notches onto Hub Spokes.
Step ➌ Install Take-Up Core 16 980348-001 Rev. A Using Options Press onto Hub Align Notches onto Hub Spokes.
Step ➍ Tighten Ribbon When using ribbon, make sure you also use thermal transfer media. 980348-001 Rev. A 17 Using Options Attach Ribbon to Take-Up Core Note: Use the adhesive strip on new rolls; ot.
Adding a New Transfer Ribbon If ribbon runs out in the middle of a print job, the indicator lights orange and the printer waits for you to add a fresh roll. Keep the power on as you change ribbon. Open the top cover, then cut the used ribbon so you can remove the cores.
Using the Label Dispenser 980348-001 Rev. A 19 Using Options Open Door Switch On the Label Taken Sensor Remove Several Labels Push Liner Through Slot Close Door Close Top Cover and Press Feed Button M.
Using Fan-Fold Media 20 980348-001 Rev. A Using Options Insert Media Adjust Holders to Width of Media Tighten Screw (use a small Phillips driver #1) Adjust Guides to Width of Media.
Using the Media Cutter Printers that have a bezel with a motorized blade can dispense one or more forms that are then automatically cut from the media supply. This option cuts through continuous paper from rolls and liner between labels. The media can be up to 0.
Clearing the Media Cutter If the blade cuts through labels, adhesive can jam the cutter. Turn OFF (O) printer power and unplug the power and interface cables before clearing the cutter. Keep the cutter dry. Never use any solutions or solvents to clean the blade.
Appendix A - Troubleshooting Problem Solution or Reason STATUS Indicator Does not light after turning ON ( I ) printer. 1. Check power connections from A.C. outlet to power supply to printer. 2. Check that media or ribbon is present. Blinks GREEN. 1. Printer receiving data through interface.
Problem Solution or Reason Printer Operation--continued Printer appears to be working (media is being fed out), but nothing is printed. 1. Verify that the labels are the correct type. 2. Check that the roll is loaded with the di - rect thermal side facing up.
Troubleshooting Media Handling Problem Solution or Reason Label Dispenser Printing continues between labels. 1. Make sure label-taken sensor is on. 2. The label-taken sensor is blocked or dirty. Remove any scraps or dust. 3. Continuous media may be set.
Serial Interface Cable Wiring The figure below displays the cable wiring required to use the printer's RS-232 serial interface. 26 980348-001 Rev.
Parallel Interface Cable Wiring The figure below displays the cable wiring required to use the printer's Centronics parallel interface. +5 volts at 300 mA for external device (e.g. KDU or scanner) 980348-001 Rev. A 27 Appendix A - Troubleshooting PRINTER DB - 25 Pi n No .
Universal Serial Bus (USB) The table below provides the contact terminat - ing assignments by number and electrical value for the cable connectors. Contact Number Signal Name Typical Wiring Assignment.
Cleaning the Print Head When you load new media, you can also clean the print head. Turn OFF (O) the printer before performing this procedure . 980348-001 Rev.
Cleaning the Platen The platen, over time, picks up adhesive and dust which requires occasional cleaning. To follow these steps, you require a clean, lint-free cloth lightly moistened with isopropyl alcohol. Turn OFF (O) the printer before performing this procedure.
Preparing Media, Paper, and Labels Before Loading During shipment, the outside length of media may become dirty when handled or dusty when stored. A preparation before loading media makes sure both the print head and platen stay cleaner for more time.
980348 - 001 A.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Zebra Technologies 2844 Printer è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Zebra Technologies 2844 Printer - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Zebra Technologies 2844 Printer imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Zebra Technologies 2844 Printer ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Zebra Technologies 2844 Printer, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Zebra Technologies 2844 Printer.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Zebra Technologies 2844 Printer. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Zebra Technologies 2844 Printer insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
