Manuale d’uso / di manutenzione del prodotto 2250M del fabbricante Ultra Start
Vai alla pagina of 16
FCC/ID Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
2250 Wiring Diagram Page 3 Pre-Installa tion Page 4 Components Recommended Pre-Installation Procedures Recommended Install Procedures Wire Connectors Page 5 6 Pin Connector 14 Pin Connector 3 Pin Red .
YELLOW WHITE/BLUE BLACK BROWN RED/WHITE PURPLE BLUE/WHITE PINK BLACK/WHITE BLUE WHITE GREEN/WHITE GREEN ORANGE 4 PIN Blu e SIDE VIEW ACTIVE RF ANTENNA Jumpers The jumpers control the output on the white wire from the six pin harness. Place the jumpers in the above order to change the output.
Recommended Pre-Installation Procedures - Control module - Remote transmitter(s) - Antenna with built in program button and LED’s - 6 pin main harness with dual 30amp power inputs - 14 pin harness -.
Yellow Starter 30amp output 12volts during crank only. Green Heater 30amp output 12volts in accessory. Off during start. Red 12 power 30amp input Constant 12volt power at ignition harness. Red 12 power 30amp input Constant 12volt power at ignition harness.
QUICK START IN STALL QUICK START IN STALL Yellow Starter Output Connect The Yellow Wire From The 6 Pin T o The Vehicles Starter Wire. Green Heater Output Connect The Green Wire From The 6 Pin To The Vehicles Accessory Wire. Red 12 power Input Connect to Constant 12 Volt Power Source - High Current.
QUICK START IN STALL Program mode allows you to adjust the settings and options of your system. Your system has been intelligently designed by installers with years of experience. The system’s default settings do not require any program changes in most cases.
PROGRAM MODE - USER SETTINGS 1 Double Pulse Unlock 1 Flash Single .75sec.Lock pulse and double Unlock Pulse 2 3 Second Lock & Unlock 2 Flashes 3 second pulses for Lock & Unlock *3 0.
PROGRAM MODE - ALARM SETTINGS Enter Alarm Program Mode - See Page 7 for details on entering program mode Press the Program Button 1 time to select setting 1 (This will be confirmed by 1 LED flash) Press and hold the Program Button until you receive the appropriate # of park light flashes and siren chirps.
1 Type 1 1 Flash Unlock before start and a lock pulse after start & shutdown 2 Type 2 2 Flashes Lock pulse after remote starter shuts off 3* Normal Operation 3 Flashes No additional re-lock pulses 1Negative Input/ 30seconds 1 Flash Waits a maximum 30 seconds before starting.
PROGRAM MODE - TACH SETTINGS Setting 1- Method 2- Low Idle Tach Learning Setting 2- Adjust For Over-Crank (Tach or T achless) Setting 3- Adjust For Under-Crank (Tach or T achless) Shock Sensor - Self Learn Mode Anti Car Jacking Mode Step 1 - Enter Program Mode (Ignition ON-OFF-ON-OFF-ON) then press the Program button on the antenna 1 time.
Manual Transmission Remote Starters must have both the door trigger and park brake wires connected. Most installs will require a clutch bypass. This is a temporary bypass. The clutch should only be bypassed during the activation of the remote starter.
ACTIVATING SERVICE MODE 1. While the ignition is “ON” press and hold the Program Button for five seconds. The park lights will flash and the siren will chirp five times to confirm that the system is in Service Mode. 2. While in Service Mode the remote start functions will be disabled and LED’s will be “ON” steady.
14 INSTALLATION GUIDE OPERATIONS OPERATIONS 1. Press and hold the # button for two seconds. 2. The system will flash the park lights and chirp the siren five times. **This feature can help find your vehicle in a crowded parking lot. 2 sec . 1.Press and hold the UNLOCK button for three seconds.
INSTALLATION GUIDE OPERATIONS OPERATIONS Remote Start Remote Stop Idle Mode Turbo Timer Mode Timer Mode Self Learning Shock Sensor 1.Press and release the button.
Blue Green Lock Un lock V ehicle Lock/Unlock Switch T o Control Relay or Actuators 87 86 85 87a 30 87 86 85 87a 30 87 86 85 87a 30 Lock Un lock Veh icle Lock/Unlock Switch To C ontrol Relay or Actuato.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Ultra Start 2250M è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Ultra Start 2250M - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Ultra Start 2250M imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Ultra Start 2250M ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Ultra Start 2250M, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Ultra Start 2250M.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Ultra Start 2250M. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Ultra Start 2250M insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
