Manuale d’uso / di manutenzione del prodotto Huntingdon 30 del fabbricante Stovax
Vai alla pagina of 23
H u n t i n g d o n 3 0 C o a l E f f e c t S t o v e C on v en t io n al F l ue With upgradeable control valve I ns t r uc t io n s f or U se , I ns t a ll a ti o n a nd S er v i ci n g Fo r use i n G B, IE (G re at Br it ain a nd Ei re ) PR0928 Issue 1 (June 2007) IMPORTANT Do not attempt to burn rubbish in this fire.
2 CONTENTS COVERING THE FOLLOWING MODELS HUNTINGDON 30 8503CFMCUC P8503CFMCUC PAGE APPLIANCE COMMISIONING CHECKLIST 3 USER INSTRUCTIONS 4 INSTALLATION INSTRUCTIONS 8 Technical Specifications 8 Site Re.
3 FLUE CHECK PASS FAIL 1. Flue is correct for appliance 2. Flue flow test 3. Spillage test GAS CHECK 1. Gas soundness & let by test 2. Standing pressure test mb 3. Appliance working pressure (on High Setting) mb NB All other gas appliances must be operating on full 4.
1.1 A competent person must carry out installation and servicing. 1.2 In all correspondence, please quote the appliance type and serial number, which can be found on the databadge located on a plate under the appliance.
5 4.2 STANDARD REMOTE CONTROL This remote control can control the gas appliance after the pilot has been lit. It can turn the main burner on and regulate it from low through to high and back again. It can turn the main burner off leaving the pilot burning GAZCO PART NUMBER 8455.
6 USER INSTRUCTIONS ADVICE ON HANDLING AND DISPOSAL OF FIRE CERAMICS The fuel effect and side panels in this appliance are made from Refractory Ceramic Fibre (RCF), a material which is commonly used for this application.
7 7.1 Ensure the rope seal fitted to the rear of the glass frame is intact. • Use a ceramic glass product generally sold for cleaning ceramic hobs to clean the glass front • Refit glass frame and .
8 INSTALLATION INSTRUCTIONS TECHNICAL SPECIFICATION Covering the following models 8575MCUC - P8575MCUC Model Gas Gas Working NOX Aeration Injector Gas Rate Input kW (Gross) Country CAT. Type Pressure Class m 3 /h High Low Huntingdon 30 I 2H Natural Gas 20 mbar 5 1 x 7.
9 INSTALLATION INSTRUCTIONS SITE REQUIREMENTS 1.1 The chimney or flue system must comply with the rules in force, and must be a minimum of 127mm in diameter. (5"). 1.2 The minimum flue height for the appliance must be 3 metres (10ft). Any horizontal flue run from the rear outlet must not exceed 100mm from the back of the appliance.
minimum of 10 minutes must be allowed before trying to relight. If this safety device is continually shuts off the gas it can suggest a serious problem: • Contact Gazco 2.8 Do not alter or tamper with the Flue Sure System. Use only genuine Gazco replacement parts when servicing the system - refer to the Servicing Section, Replacing Parts .
11 INSTALLATION INSTRUCTIONS INSTALLATION 3.5 The flue system can now be connected to the stove: • Ensure all joints are sealed with a suitable fire resident sealant.
12 • Place the front coal between the heat shield and the flame baffle so that its ends sit flat against the burner skin Diagram 9 • Put five of the round coals on the front between the fingers of the flame baffle.
13 • Now replace top, Diagram 15 5.1 Full instructions are given in the User Section . 6. LIGHTING 15 AR1907 14 AR1908 INSTALLATION INSTRUCTIONS INSTALLATION.
14 INSTALLATION INSTRUCTIONS COMMISSIONING • Close all openable doors and windows in the room • Ignite the stove and operate on maximum for 10 minutes • Remove the plastic sight plug from the ri.
15 IGNITION FUNCTIONAL CHECK 1 PILOT WILL NOT LIGHT Ensure there is no debris around the pilot assembly, (e.g. soot, etc.) which could short the spark, clean the area. Operate the valve. Is there a spark? Consult Section 2 and retry. Check alignment of pilot burner head, change the ignition lead, see diagram 1 on page 17.
16 PILOT WILL NOT STAY LIT OR FIRE GOES OUT IN USE Ensure there is no debris around the pilot assembly, e.g. coal, soot etc. which could short the spark, clean the area. Problem is with the pipework or fittings which lead to the fire. Correct and retry.
17 2.4 Remove the two screws at the back of the firebox and lift the burner unit clear Diagram 3 3.1 • Follow the procedure for removing the main burner When the burner is out: • Remove the aeration cover by undoing the two screws, Diagram 4 • Remove the lint arrester, by folding the tabs back Diagram 5 AR1444 5 AR1443 4 AR1442 3 1.
18 The pilot unit can now be removed by undoing the two screws, Diagram 6 3.2 • Reassemble in reverse order • Do not overtighten. NOTE: TAKE CARE NOT TO DISCONNECTTHE SENSOR WIRES OF THE GAZCO FLUE SURE SYSTEM ON REPLACING THE THERMOCOUPLE 4.
19 6.2 There is a small cylindrical metal spacer inside the cover, this must be kept and replaced on the fixing screw during re-assembly • Disconnect the ignition lead from the gas valve • Undo th.
20 9.1 • Open the door and remove the ceramics, placing them carefully to one side. • Undo the two screws in the back of the firebox and carefully withdraw the bracket, Diagram 14 and 15 9.2 • Disconnect the two sensor wires • Undo the two taptite screws • Remove the sensor and the two plastic spacers, Diagram 16 9.
NG LPG COMPONENT G20 G31 20mb 37mb MAIN INJECTOR IN0001 IN0054 AERATION PLATE ME4066 ME4954 PILOT INJECTOR PI0036 PI0037 BURNER ASSEMBLY B0214 PB0214 THERMOCOUPLE PI0010 MAGNETIC UNIT GC0092 ELECTRODE.
22 SERVICE RECORDS 1ST SERVICE 2ND SERVICE Date of Service: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date of Service: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Next Service due: . . . . . . . . . . . . . . .
Gazco Limited, Osprey Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7JG Tel: (01392) 261999 Fax: (01392) 444148 E-mail: info@gazco.com A member of the Stovax Group.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Stovax Huntingdon 30 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Stovax Huntingdon 30 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Stovax Huntingdon 30 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Stovax Huntingdon 30 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Stovax Huntingdon 30, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Stovax Huntingdon 30.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Stovax Huntingdon 30. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Stovax Huntingdon 30 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
