Manuale d’uso / di manutenzione del prodotto 5000RS del fabbricante Scytek electronic
Vai alla pagina of 48
GALAXY 5000RS/2000RS SERIES-DBP DATA BUS PORT VEHICLE SECURITY SYSTEM WITH REMOTE START PRODUCT MANUAL.
L i m i t e d L i f e t i m e W a r r a n t y This vehicle security system is warranted to the original purchaser , to be free from defects in material and workmanship.
1. About Y our System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1 2. Remote T r ansmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
The ScyT ek Galaxy 5000RS-DBP Series is a Combination Vehicle Security and Remote Starting System , Galaxy 2000RS-DBP Series is a Remote Starting with keyless entry . featuring a built -in "ScyNet Network Port" that allows direct connection of optional accessory modules and a PC interface off ering expanded system operation.
Standard Remote Transmitter Description Depending on the model chosen, the Galaxy 5000/2000RS-DBP Series will be supplied with one or two T5 or T5-SP 5-button R emote T ransmitters that are used to control the system’ s operations.
Adding/Replacing Standard Remote Transmitters T o replace lost or stolen tr ansmitters or to add additional transmit ters into the system, have all desired transmit ters ready and follow the steps below . Note : Up to 4 one-wa y transmitters can be progr ammed to operate the system.
2-way LCD Remote Transmitter Description Depending on the model chosen, the Galaxy 5000/2000RS-DBP-2W Series will be supplied with one or two 2-way LCD R emote T ransmitters, of fering increased range and confirmation of an y activated f eatures.
· The LED will illuminate. 3. Press and release Button 1 on the first tr ansmitter then on the second transmit ter . · The siren/horn will chirp/honk once for every tr ansmitter learned. 4. T urn off the ignition k ey . 5. The siren/horn will chirp/honk 3 times to indicate the system has exited programming mode.
T o set the daily start feature: 1. Press and hold Buttons 2 and 3 until the remote beeps four times. · The fan and clock will be shown indicating daily start mode is entered. 2. Press Button 2 until the desired hour is displayed. 3. Press Button 3 until the desired minute is displayed.
Galaxy 5000/2000RS-DBP - Page 7 CHP Set the siren/horn confirmation chirps/honks ON or OFF : 1. Press and hold Button 5 until the display shows CHP . ·The transmit ter will beep three times.
Page 8 - Galaxy 5000/2000RS-DBP.
Galaxy 5000/2000RS-DBP - Page 9 Button 1 Button 2 Button 3 Button 4 Button 5 11/16 3:10P Battery status wakeu p alarm enabled autostart enabled date/engine run timer time Optional 2-wa y Color remote transmitter is off ering increased range and confirmation of any activ ated feature.
Page 10 - Galaxy 5000/2000RS-DBP Press and hold Buttons 2 and 3 until pager progr am features are displayed. Select pager setting by pressing buttons 1 or 2 to highlight the remote pager . Press button 3 to select the pager . Setting Date & Time Select Time Date setting by pressing buttons 1 or 2 to highlight the f eature.
Galaxy 5000/2000RS-DBP - Page 11 Use buttons 1 & 2 to highlight the time par ameter you wish to change, use buttons 3 & 4 to scroll up or down to chage the time. Save the changes by pressing but ton 5. Setting Alarm Clock Select Alarm setting by pressing buttons 1 or 2 to highlight the f eature.
Page 12 - Galaxy 5000/2000RS-DBP Return to Previous Screen Select Previous Screen by pressing buttons 1 or 2 to highlight the feature. Press but ton 3 to select it. Press and hold Buttons 2 and 3 until pager progr am features are displayed. Select system setting by pressing buttons 1 or 2 to highlight the siren.
Galaxy 5000/2000RS-DBP - Page 13 Setting AutoStart Cold Temperature Threshold Select Cold T emp start setting by pressing but tons 1 or 2 to highlight the feature. Press button 3 to select it. Use buttons 3 & 4 to scroll up or down to chage the temper ature threshold.
Page 14 - Galaxy 5000/2000RS-DBP Select Clock Sync set ting by pressing buttons 1 or 2 to highlight the arrows. Press button 3 to select the pager . Pager Clock Sync This feature synchronizes the pager clock to the security system time of a da y clock.
Galaxy 5000/2000RS-DBP - Page 15 Use buttons 1 & 2 to highlight Set Time press button 3. The security system responce. Start Time 2 This feature sets the system Autostart 2 time. Select Sytem Clock S ync by pressing buttons 1 or 2 to highlight the feature.
Page 16 - Galaxy 5000/2000RS-DBP Pressing and holding transmit ter button 5 will scroll through sever al transmitter progr ammable options - TEMPERATURE, ENABLE COLD START, ENABLE HOT START, VALET MODE, ENABLE AUTOSTART 1, ENABLE AUTOSTART 2. TEMPERATURE Check the temperature inside the vehicle 1.
Galaxy 5000/2000RS-DBP - Page 17 Transmitter Lockout Press and hold buttons 2 & 4 simultanously for 3 seconds to lockout the tr ansmitter against accidental transmission. Release Transmitter Lockout Press and hold buttons 2 & 4 simultanously for 3 seconds to release the transmit ter from Lockout.
Page 18 - Galaxy 5000/2000RS-DBP P P a a g g e e r r S S t t a a t t u u s s D D i i s s p p l l a a y y Time: time of day clock Date/Engine Run Timer: date, or engine run minute timer if remote start activated (20 min max). Battery Status: displays remaining battery life.
Galaxy 5000/2000RS-DBP - Page 19 Remote Arming/Locking The system monitors 5 independent areas ( zones ) while armed: doors, hood/ trunk, shock sensor , optional sensor input, and the network port for future expansion. T o Arm and Lock the S ystem: 1.
Page 20 - Galaxy 5000/2000RS-DBP Tamper Alert If the system was triggered while awa y , the LED will flash to indicate which zone triggered the system after disarming and turning the ignition ON.
Galaxy 5000/2000RS-DBP - Page 21 Panic Mode In the event of an emergency , the transmit ter’s remote P anic feature can be used to instantly trigger the alarm/panic feature. T o activ ate the Panic Mode: 1. Press and hold Button 1 for fiv e seconds.
Page 22 - Galaxy 5000/2000RS-DBP 3. Press the valet switch 4 times. · The siren will chirp each time the valet switch is pressed. 4. Within 5 seconds, press Button 3 on the tr ansmitter . · The siren will chirp 3 times. 5. Press the valet switch the number of times equal to the desired code (from 1-15).
Galaxy 5000/2000RS-DBP - Page 23 Remote Starting T o R emote Start the System: 1. Be sure the system is not in V alet Mode. 2. Press and hold Button 4 for three seconds. · The parking lights will flash 4 times and turn on. · The siren/horn will chirp/honk 4 times.
Page 24 - Galaxy 5000/2000RS-DBP Automatic Start Mode Automatic Start feature has three modes that will start the vehicle every one or two hours within a 24 hour period. 1. Timer Only Mode (factory def ault) The Automatic Start feature starts the vehicle automatically ev ery one or two hours and runs for the preset Run Time.
Galaxy 5000/2000RS-DBP - Page 25 Model: Galaxy 5000/2000RS-DBP-M 1- T ach wire must be connected , The system must learn RPM. 2- Hand brak e must be connected. 3- Door trigger must be connected 4- Clutch override installed NOTE: MUST USE RELAY, SEE PAGE 26.
Page 26 -Galaxy 5000/2000RS-DBP E x t e n d e d F e a t u r e s Ignition Door Locking F or added safety , the Ignition Door Locking f eature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on.
Galaxy 5000/2000RS-DBP - Page 27 1. Thoroughly read and become familiar with the installation instructions bef ore beginning the installation. 2. R eview system contents: Main Unit 1 or 2 One-wa y 5 B.
Page 28 - Galaxy 5000/2000RS-DBP Mounting the Control Unit The control unit must only be mounted in the interior of the vehicle. Do not mount the main unit in the engine compartment.
Galaxy 5000/2000RS-DBP - Page 29 S y s t e m W i r i n g 6-Pin Starter Harness Pin 1 RED WIRE A : Main P ower Input A (+). Connect to the battery or constant power wire at the ignition switch with a minimum 25 Amp supply . R emo v e the f use until the installation is complete and all wiring is check ed.
Page 30 - Galaxy 5000/2000RS-DBP Pin 12 GREEN WIRE : Negative Door Input (-). Connect to the door switch circuit wire that shows ground when the door is open. Pin 13 WHITE/BLACK WIRE : Hood/T runk Pin Input (-). Connect the to the hood/trunk pin switch.
Galaxy 5000/2000RS-DBP - Page 31 2-Pin White Connector: Located on the side of the main module. · Green WIRE - Parking Br ake Input (-) Fo r Manual T r ansmission and/or vehicles equipped with a turbo charged engine. Must be connected if using the T urbo Timer feature and/or Manual T ransmission remote start feature.
Page 32 - Galaxy 5000/2000RS-DBP Entering System Programming This system is compatible with both the LCD two wa y transmitter or the standard tr ansmitter , all system programming can be perf ormed using either one. T o enter S ystem Programming: 1. T urn the ignition switch to the ON position.
Galaxy 5000/2000RS-DBP - Page 33 5. Ignition Door Unlocking. Selects whether or not the system automatically unlocks the doors when the ignition is turned off . The Ignition Door Locking feature may be progr ammed to unlock all doors or the driver’ s door only .
Page 34 -Galaxy 5000/2000RS-DBP 6. Door Unlock Pulse. Selects between one pulse or two pulse operation for the door unlock output. Many new import vehicles’ f actory door locking systems require two pulses on the proper wire to unlock the doors.
Galaxy 5000/2000RS-DBP - Page 35 16. Auxiliary 3 Output Mode. Selects between Channel 3, F actory Rearm output, or third I gnition ouput. 17 . Lock After Start. When selected, the doors will automatically lock after remote starting. Using button 3 disabled Mp Siren Mode .
Page 36 - Galaxy 5000/2000RS-DBP 28. Siren Mode. Selects standard siren (defualt) or MP Player Siren. 29. Turbo Timer. When enabled, if the emergency brake has been applied Ignition power will be k ept On for a predetermined time (2 minutes F actory Default) from the application of the emergency br ake.
Galaxy 5000/2000RS-DBP R e l a y D i a g r a m s P ositive Dome Light Activ ation Negative Dome Light Activ ation P ositive Horn Honk Negative Horn Honk Starter Defeat/Anti-Grind Negative Glow Plug.
Page 38 - Galaxy Negative T rigger R everse P olarity V acuum Adding Actuators F ollow the diagrams below for connecting basic door lock systems. F or T wo Stage door lock systems (separately unlocks driv er and passenger doors) see following pages.
Galaxy 5000/2000RS-DBP T w o S t a g e D o o r L o c k D i a g r a m s T wo Stage Negative T rigger T wo Stage P ositive T rigger The Galaxy 5000/2000RS-DBP Series is equipped with a dedicated P assenger Unlock output allowing T wo Stage Door Lock operation.
Page 40 - Galaxy 5000/2000RS-DBP T w o S t a g e D o o r L o c k Diagrams c o n t ’ d T wo Stage R everse P olarity T wo Stage Adding Actuators.
Galaxy 5000/2000RS-DBP - Page 41 FCC ID: OARRXAM2000 This device complies with P art 15 of FCC Rules. Operation is subject to the f ollowing two conditions: 1) This device may not cause harmful interference.
Page 42 - Galaxy 5000/2000RS-DBP S t a r t e r D i a g n o s t i c s Starter doesn’t start and parking lights flash: 3 Times - Engine RPM not detected (check tach wire and/or perform tach learn proc.
Galaxy 5000/2000RS-DBP - Page 43 Shock Sensor Adjustment: Clock wise increases sensitivity S h o c k S e n s o r A d j u s t m e n t.
ScyTek Electronics 11627 Cantara Street North Hollywood, CA 91605 www .scytek.net © ScyT ek Electronics 2010 Galaxy DBP 10-19-10 W i r i n g D i a g r a m ScyNet Blue Aux S tart (-) / T urbo T imer C.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Scytek electronic 5000RS è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Scytek electronic 5000RS - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Scytek electronic 5000RS imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Scytek electronic 5000RS ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Scytek electronic 5000RS, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Scytek electronic 5000RS.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Scytek electronic 5000RS. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Scytek electronic 5000RS insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
