Manuale d’uso / di manutenzione del prodotto AS-1412 del fabbricante Autostart
Vai alla pagina of 14
Notice The manufacturer will accep t no responsibility for any electrical damage resulti ng from imprope r installation of the product, be that either da mage to the vehicle itself or to th e Unit. This Unit must be installed by a certifie d technicia n using all safety dev ices supplied.
P. 2 Installation Guide AS-1412 Introduction This Guidebook conta ins all informa tion pertinent to t he installation. Most (if not al l) features are grouped in t he User Guidebook and therefore, should you need infor mation on a featur e, you should refer to the User Guidebook.
AS-1412 Installation Guide P. 3 Before You Get Started … Ƈ On vehicles with a manual Transmission, always ensure that all Doors will get the Unit out of Ready Mode. Switch the wir e used so that it is triggered by all Doors. Ƈ Make sure that the Parking Brake and Door Switch contacts work properly.
P. 4 Installation Guide AS-1412 Harness Description When connecting the Module, it is important to make sure that th e connector with the Ground w ire is connected first, before making the 12-volt con nections. Should the Unit be powere d up before being grounded, there could be seri ous damage to internal components of the Un it.
AS-1412 Installation Guide P. 5 5-Pin Secondary Harness Wire Description 1 BLACK (–) Chassis ground input This wire must be connected to bare, un painted metal (the Chassis or true Body ground). It is prefer able to use a factory groun d bolt rather than a s elf- tapping screw.
P. 6 Installation Guide AS-1412 Note: The system also gives a Disarm pulse on this wire before remote start. 6 BLUE / WHITE (–) L.E.D. output 2 V L.E.
AS-1412 Installation Guide P. 7 Ignition barrel). Option 4 (Smart Ignition Re-Lock): Connects to th e Negative Door trigger Input. When the Ignition Loc k Option or the Lo ck Only Option is enabled: after t he Brake Pedal is pressed and after a Door has been opened and closed, the Do ors will RE-LOCK .
P. 8 Installation Guide AS-1412 12 YELLOW (+) Glow-plug input (Cont.) -plug input on the Mod ule may be “timed ou t”. The Module will power up th e Ignition and Glow-pl ug circuits and simply wait.
The Programming Assistance Button (a.k.a. PAB.) The PAB is located on the side of the M odule. This push button mi mics the Hood-Pin switch in order to avoid having to get ou t of the vehicle and pr essing the Hood-Pin switch. The PAB will work only when the Hood is up.
P. 10 Installation Guide AS-1412 to re-enter all opti on selections for all functio ns of the Mode you are accessing. You may not skip Functions*. *NOTE: Pressing the Brakes at any given moment will save the s electio n(s) you have entered and will return you to the Programmi ng Center.
AS-1412 Installation Guide P. 11 Auto Tach Programming Procedure NOTE: If no tach has bee n programmed and the ,, button is pressed, there will be no start attempt and t he vehicle will give 5 flash es. If another Tach Progra mming is required, simply repeat the Auto Tach Programming Proc edures.
3. Test the Brake shutdown circuit : With the ve hicle running und er the Remote St arter, press and releas e the Brake Pedal. The Engine sh ould shut down i mmediately. If th e Engine continues to run, check the Brake Switch con nection. 4. OEM Alarm Control: Make sure the Module is able to arm and disarm the OEM Alarm (if applicable).
AS-1412 Installation Guide P. 13 Caution: The relay output rating on this Unit is 25 A at mo st. Defective OEM solenoid switches can sometimes draw up to 50 or 60 A, causing the 30 A fu se to blow. Always check your circuit with a proper measuring device.
P. 14 Installation Guide AS-1412 1. FLASH the hood pin switch. 2. In ten seconds or less, pr ess the Brake Pedal six times. 3. The Parking Lights will fl ash 8 times confirming the Reset. Table 6 On some vehicles, such as, BMW, and certain Volkswagens, etc.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Autostart AS-1412 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Autostart AS-1412 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Autostart AS-1412 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Autostart AS-1412 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Autostart AS-1412, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Autostart AS-1412.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Autostart AS-1412. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Autostart AS-1412 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
