Manuale d’uso / di manutenzione del prodotto 128-7405B del fabbricante Audiovox
Vai alla pagina of 28
128-7405B 1 of 28 Model APS-998 Installation Manual The selectable features can be set manually as explained below , or with the RF feature programmer . T o set features using the RF programmer , follow the instructions packaged with the programmer . Factory default settings are indicated by bold text.
128-7405B 2 of 28 2 T o program these select able features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn .
128-7405B 3 of 28 3 T o exit program mode, turn ignition off, or press and release valet switch. RF Programmable Features Bank 3 Is Remote Start Selectable Features: Feature Selection 1 Chirp 2 Chirps.
128-7405B 4 of 28 4 Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off, On, Off, On Short chirp, then 2 long chirps This .
128-7405B 5 of 28 V ehicles Only! The unit provides a selectable ignition control that allows a number of selectable timed outputs for glow plug pre-heat in addition to a "W ait T o S tart Input" either of which may be required for certain diesel vehicles, (see selectable feature #1 1 Bank 3 & or Green/Y ellow Wire) .
128-7405B 6 of 28 DASH MOUNTED LED: The small LED included in the kit will serve as a visual indicator of the alarm's status and provide a visual deterrent to a potential thief. The LED also provides important feed back information during the transmitter and feature program modes.
128-7405B 7 of 28 relay to an existing harness in the chosen location using a cable tie around the relay's wiring harness. CAUTION! Do not wire tie the metal bracket to an existing wiring harness as vibration may cause chaffing and shorting damaging the factory wiring.
128-7405B 8 of 28 IMPORT ANT! It is the responsibility of the installing technician to determine the load factor of the vehicles electrical circuits when the vehicle is running, and to adequately fuse the two power wires based on that load.
128-7405B 9 of 28 GREEN Wire: Ignition 2 Output Connect this wire to the ignition 2 wire from the ignition switch. This wire will show + 12 volts when the ignition key is turned to the "ON" or "RUN" position and is some cases the "ST AR T" or CRANK" position.
128-7405B 10 of 28 White w/ Black T race Wire: (+) Siren Output This is the positive siren feed wire. Route this wire through a grommet in the firewall to the siren location. Connect the White w/ Black Trace wire to the Red wire of the Siren. Secure the Black wire of the Siren to a known chassis ground or solid clean metal surface.
128-7405B 11 of 28 Siren Wiring Detail 11 (-) TO VEHICLE'S CHASSIS GROUND TO WHITE w/BLACK WIRE OF MODULE Purple Wire: (+) Door Trigger Input If the vehicle's door courtesy light switches + .
128-7405B 12 of 28 A. Shock Sensor By Pass: If there is a Non Plug in Shock Sensor used with the alarm system and it is not shunted during the Remote S tart activation period, then vibration from the running vehicle can cause the alarm to trigger . In this case, connect the Light Blue Wire to terminal #86 of a external relay .
128-7405B 13 of 28 13 Entry Illumination Detail Grey w/ Black T race W ire: Negative Inhibit Input Plus T rigger When Armed The Grey w/ Black T race wire provides an instant shut down for the Remote S tart Control Module whenever it is grounded also trigger for the alarm when armed.
128-7405B 14 of 28 Brown w/ Black T race W ire: Positive Inhibit Input Plus T rigger When Armed The Brown w/ Black T race wire provides an instant shutdown for the Remote S tart Control module when- ever it gets + 12 volts also triggers the alarm when armed.
128-7405B 15 of 28 15 Green w/ Orange T race Wire: T achometer Input Signal This wire will continually monitor the engine's tach rate while the unit is under power of the Remote S tart module.
128-7405B 16 of 28 Channel 3 Relay Wiring Detail 16 Green w/ Black T race Wire: 300mA Latched Channel 4 Output The Green w/ Black Trace wire supplies a 300 mA switched output whenever channel four of the receiver is accessed.
128-7405B 17 of 28 17 NOTE : This is a normally opened starter cut arrangement, when power is removed from the security system, the starter disable feature will remain operational, and the vehicle will not start. Audiovox does not recommend using the Orange w/ White trace wire to interrupt anything but the starting circuit of the vehicle.
128-7405B 18 of 28 18 Black w/ Y ellow T race Wire: Ground Output During S tart (Crank) The Black w/ Y ellow T race wire will provide a 300 mA ground output while the starter output of the remote start unit is active. This output can be used to activate the Crank Low/Bulb T est wire found in some GM vehicles.
128-7405B 19 of 28 19 3 Wire Positive Switched Door Locks: In this application, the Red wire of the door lock harness provides a + 12 volt pulse during the disarming sequence, or pulsed 12 volt unlock output. Connect the Red wire to the low current 12 volt signal wire from the factory door unlock switch to the factory door unlock relay .
128-7405B 20 of 28 The Red/Black wire provides a pulse ground output when the unlock button of the transmitter is pressed a second time after disarming. Connect the Red/Black wire to the wire that provides a low current ground signal from the factory door unlock switch to the factory door unlock control relay .
128-7405B 21 of 28 21 NOTE: Resistive Circuit s, As W ell As 4 W ire Polarity Reversal and 5 W ire Alternating 12 V olt Door Lock Control Circuits These applications require the use of additional components which may include relays, fixed resistors, or for convenience, a Door Lock Interface.
128-7405B 22 of 28 22 TEMPERA TURE ST ART : When T emperature Start, Bank 3 feature #13 is selected on, the temperature st art mode can be activated from the transmitter .
128-7405B 23 of 28 coils. T o achieve optimum performance the coil signals must be evenly distributed. This is accomplished by first mapping out the firing order of the engine in groups of as indicated below .
128-7405B 24 of 28 If the unit fails this test, recheck your enable switch connection to the Ground and the Black/White wire of the Audiovox Remote S t art Unit. If you have a plug in enable switch, check that the two pin connector is firmly seated in the mating connector on the control module.
128-7405B 25 of 28 25 4. Connect the other side of the enable switch to the Black/White enable input wire of the Remote S tart unit. The reference diagram below shows a typical GM B Body ECM reference wire and how it is to be connected to the Remote S t art Unit.
128-7405B 26 of 28 METHOD 2 T o connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground.
128-7405B 27 of 28 27 be connected to the hood pin switch. If the hood pin switch is also used for an alarm trigger input, be certain to use the dual diode assembly packaged with the Audiovox Remote S tart Unit as shown in this installation guide.
128-7405B 28 of 28 28 © 2006 Audiovox Electronics Corp., Hauppauge, NY 11788 WWW .audiovox.c om For Customer Service Vis it Ou r Web si te At Product Information, Photos, F A Q’s Owner ’ s Manual.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Audiovox 128-7405B è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Audiovox 128-7405B - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Audiovox 128-7405B imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Audiovox 128-7405B ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Audiovox 128-7405B, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Audiovox 128-7405B.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Audiovox 128-7405B. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Audiovox 128-7405B insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
