Manuale d’uso / di manutenzione del prodotto 495 del fabbricante Remington
Vai alla pagina of 44
Operating Instructions Important : Bien lire ce manuel et toutes les étiquettes avant de faire fonctionner l’outil à poudre. Ce manuel doit toujours accompagner l’outil et être transféré avec lui en cas de changement de propriétaire.
2 101719 INDEX Warning: Safety Precautions ........................................................... 4-16 Why A Fastener Holds ................................................................... 17-18 Selecting Fasteners and Power Loads ............
3 101719 Power Pro MC Semi-Automatique Mod è le 495 Le Power Pro MC Remington Mod è le 495 est con ç u pour ê tre utilis é avec les bandes de charges de calibre 27 Remington et les fixations Remington qui ne sont pas plus longues que 63 mm (2-1/2").
4 101719 A vertissement: Mesures de pr é cautions W arning: Safety Precautions IMPORTANT: Read these operating instructions carefully and com- pletely before trying to operate or service this tool. Improper use of this tool can cause serious injury or death from firing fastener into body or from flying debris.
5 101719 Safety Precautions Mesures de pr é cautions D É FECTUEUX DEFECTIVE 2. Always inspect to make sure the tool is working properly. If the tool does not work properly, remove from service and tag “ DEFECTIVE. ” Do not use the tool again until it has been properly repaired.
6 101719 482-12 Safety Precautions Mesures de pr é cautions G 018 5. Make sure the work area is clean from loose material and debris. S ’ assurer qu ’ il n ’ y a pas de mat é riaux et de d é bris é pars dans la zone de travail. HANDLING THE TOOL MANIPULATION DE L ’ OUTIL G 018 1.
7 101719 Safety Precautions Mesures de pr é cautions G 018 3. Store powder actuated tool and power load strips in a locked container. Unload tool before storing. Keep power loads of different power levels in separate containers. Ranger l ’ outil à poudre et les bandes de charge dans un contenant verrouill é .
8 101719 ? ? ? Safety Precautions Mesures de pr é cautions G 018 G 018 6. Always take precaution to maintain your balance while operating a powder actuated tool. Toujours faire attention à garder son é quilibre lorsqu ’ on utilise un outil à poudre.
9 101719 Safety Precautions Mesures de pr é cautions KNOW YOUR FASTENING BASE MATERIAL BIEN CONNA Î TRE LE MAT É RIAU DE BASE TOO BRITTLE TROP FRAGILE Surface shatters La surface se brise en é cla.
10 101719 CAST IRON FONTE GLASS VERRE TILE CARRELAGE BRICK BRIQUE Safety Precautions Mesures de pr é cautions 2. Never attempt to drive power fasteners into very hard or brittle materials including, but not limited to cast iron, glass, tile, stone, brick, or hardened steel.
11 101719 TOO THIN TROP MINCE WELD SOUDURE 5. Do not fasten through or within 13 mm (1/2") of predrilled or pre-punched holes. Ne pas enfoncer de fixations à moins de 13 mm (1/2") d ’ un trou fait ou drill é à l ’ avance ni à travers un tel trou.
12 101719 NO NON Safety Precautions Mesures de pr é cautions G 018 8. When fastening into masonry walls, always drive into horizontal mortar joints, never into vertical mortar joints. Be careful. A poorly laid joint may permit too much penetration, and/or unsatisfactory holding power.
13 101719 482-49 Safety Precautions Mesures de pr é cautions tout en maintenant la bouche sur la surface de travail. Appuyer de nouveau l ’ outil fermement contre la surface de travail, et appuyer sur la g â chette.
14 101719 1 2 3 4 5 6 7 8 9 10 11 12 1 22 C A L I B R E C A L I B E R B R A S S • L A I T O N N I C K E L 2 2 Safety Precautions Mesures de pr é cautions NOTE: Failure to start with the lowest power level can result in overdrive condition and will result in damage to tool (See page 20).
15 101719 YELLOW? JAUNE? GREEN? VERT? RED? ROUGE? 482-59 4. Never carry fasteners or other hard objects in the same pocket or container with power load strips. Ne jamais transporter de fixations ou d ’ autres objets durs dans la m ê me poche ou le m ê me contenant que des bandes de charges.
16 101719 Safety Precautions Mesures de pr é cautions 7. Never use common nails or other materials as fasteners. Remington Power Fasteners are manufactured from special steel and heat treated to produce a very hard yet ductile fastener. Ne jamais utiliser de clous normaux ni d ’ autres mat é riaux comme fixations.
17 101719 Why A Power Fastener Holds Pourquoi les fixations tiennent 482-64 WHY A POWER FASTENER HOLDS IN CONCRETE The compression bond of the concrete to the power fastener accounts for the majority of the holding power. The fastener displaces the concrete which tries to return to its original form causing a squeezing effect.
18 101719 Why A Power Fastener Holds Pourquoi les fixations tiennent WHY A POWER FASTENER HOLDS IN STEEL Holding power in steel depends on the elasticity of the steel. The steel pushes back on the shank of the power fastener. Drop a marble into water; the water parts, the marble continues down, the water closes back.
19 101719 Selecting Power Fasteners and Power Loads Choix de fixations et de charges FASTENING INTO CONCRETE The proper power fastener length can be determined by adding the thickness of the material to be fastened and the amount of fastener that will actually penetrate the concrete.
20 101719 Selecting Power Fasteners and Power Loads Choix de fixations et de charges OVERDRIVEN POWER FASTENERS AND PISTON An overdriven power fastener results when too strong of a power load is used causing the piston to extend past the muzzle. Move to the next lightest power load.
21 101719 Operation Utilisation 1. Grasp barrel assembly and slide forward rapidly until it stops. Push barrel assembly back into tool to the closed position. This sets piston into firing position. Tenir le canon et le faire glisser vers l ’ avant jusqu ’à ce qu ’ il s ’ arr ê te.
22 101719 Operation Utilisation 4. Place the muzzle of tool perpendicular to work surface without tilting the tool. Push tool against work surface until sliding action of barrel stops. Placer la bouche de l ’ outil perpendiculaire à la surface de travail sans faire pencher l ’ outil.
23 101719 Operation Utilisation 7. Should the tool fail to fire, hold the muzzle firmly against the work surface for 30 seconds. Release the trigger and remove pressure on the tool while holding the muzzle against the work surface. Again press the tool firmly against the work surface and pull the trigger.
24 101719 Parts List 495 Key Part No. No. Description Qty. 1 501001 Housing 1 2 501100 Outer Liner Assembly 1 3 501104 Push Pin 1 4 301013 Ball Setter 2 5 501106 Spring Ball Set 1 6 501107 Key Stop 1 .
25 101719 1 3 2 4 5 6 7 4 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 26.
26 101719 N ° de N ° de code pi è ce Description Quantit é 1 501001 Bo î tier 1 2 501100 Garniture ext é rieure 1 3 501104 Pivot poussoir 1 4 301013 Roulement à bille 2 5 501106 Ressort de roul.
27 101719 1 3 2 4 5 6 7 4 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 26 Clean tool after each days use. Disassemble and clean the barrel assembly with the wire brush provided with tool. Notice: Do not attempt to clean power load strip channel with wire brush.
28 101719 T ool Disassembly D é sassemblage du pistolet WARNING: Always unload a powder actuated tool before disassembling, replacing barrel, cleaning, or assembling. MISE EN GARDE : Toujours d é charger un pistolet de scellement avant de le d é monter, de remplacer le canon, de le nettoyer ou de le remonter.
29 101719 3. Pull barrel assembly out of housing. Sortir du bo î tier l ’ ensemble de canon en le tirant. 4. Unscrew muzzle cap. D é visser l ’ embout de bouche. 5. Pull buffer out of muzzle cap (see Figure 3). Sortir le butoir de l ’ embout de bouche (voir figure 3).
30 101719 Figure 5 - Removing Handle Pad Assembly and Rear Pad Figure 5 - D é pose de l ’ ensemble de tampon de poign é e et du tampon arri è re Screws Vis Handle Pad Assembly Ensemble de tampon .
31 101719 D. REMOVING FIRING PIN D É POSE DU PERCUTEUR 1. Remove two springs from outer liner assembly (see Figure 8). Enlever les deux ressorts de la garniture ext é rieure (voir figure 8). 2. Push in sear and pull out firing pin guide (see Figure 8).
32 101719 MISE EN GARDE : Toujours d é charger un pistolet de scellement avant de le d é monter, de remplacer le canon, de le nettoyer ou de le remonter. F. REMOVING OUTER LINER ASSEMBLY FROM HOUSING D É POSE DE LA GARNITURE EXT É RIEURE DU BO Î TIER 1.
33 101719 C. ATTACHING FIRING PIN ASSEMBLY MONTAGE DE L ’ ENSEMBLE DE PERCUTEUR 1. Insert push pin into hole in housing next to outer liner assembly (see Figure 12). Ins é rer le pivot poussoir dans le trou du bo î tier situ é pr è s de la garniture ext é rieure (voir figure 12).
34 101719 Rocker Arm Spring Ressort de culbuteur Assembly Handle Pad Ensemble de tampon de poign é e 3mm Allen Wrench Cl é Allen de 3 mm Outer Liner Assembly Garniture ext é rieure Screws Vis Handle Pad Assembly Ensemble de tampon de poign é e E.
35 101719 F. ASSEMBLING BARREL ASSEMBLY MONTAGE DE L ’ ENSEMBLE DE CANON 1. Insert piston assembly into barrel (see Figure 17). Ins é rer l ’ ensemble de piston dans le canon (voir figure 17). Figure 17 - Inserting Piston in Barrel Figure 17 - Pose du piston dans le canon Piston Piston 2.
36 101719 Figure 20 - Pushing Stop towards Front of Tool Figure 20 - La but é e est pouss é e vers l ’ avant du pistolet 6. Push stop towards front of tool (see Figure 20). Pousser la but é e vers l ’ avant du pistolet (voir figure 20). Stop But é e 7.
37 101719 T roubleshooting Guide Piston hangs out of muzzle. Overdriven fastener. Piston jammed. Power load strip will not advance. Reduction or loss of power. Tool does not completely depress. Tool does not fire. Opening and clos- ing of barrel or pushing down on tool, etc.
38 101719 D é pannage PROBL È ME CAUSE POSSIBLE SOLUTION Outil surcharg é . Piston mal mont é par rapport à la but é e du canon. Piston ou segment de piston bris é . Puissance trop é lev é e. Fixation surcharg é e (voir ci-dessus). La barre ou le ressort d ’ avance sont endommag é s.
39 101719 Fastening Into Steel Fixation Dans L ’ acier PROBL È ME L ’ outil ne tire pas. L ’ ouverture ou la fermeture du canon ou la pression sur l ’ outil, etc. ne se fait pas en douceur, mais est plut ô t dure. CAUSE POSSIBLE SOLUTION Voir “ L ’ outil ne se d é tend pas compl è tement ” ci-dessus.
40 101719 Application Chart 482-81a to this power load color power fastener length Power load and power fastener application information. For fastening this Concrete Cement Block Steel [5 mm - 10 mm (3/16" - 3/8")] Power load listings are recommendations only.
41 101719 482-81a Pour attacher ceci à cela couleur de la charge longueur de fixation Informations sur l ’ application des charges et des fixations.
42 101719 Application Chart T ableau d ’ application IMPORTANT • Recommended for use with Remington power load strips and power fasteners. • Only use power fasteners up to 63 mm (2 1/2") long with standard guide. Power fasteners 76 mm (3") long can be used with optional guide, part number TA4095.
43 101719 Limited W arranty Agreement DESA Industries warrants the Remington Power Pro Model 495 against defects in materials and workmanship for a period of one (1) year from the date of purchase.
101719-01 REV. B 7/95 Accord de garantie limit é e DESA Industries garantit que le Powerdriver Remington Mod è le 495 est exempt de d é fauts de mat é riau et de fabrication pendant une (1) ann é e à partir de la date d ’ achat.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Remington 495 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Remington 495 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Remington 495 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Remington 495 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Remington 495, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Remington 495.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Remington 495. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Remington 495 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
