Manuale d’uso / di manutenzione del prodotto 476 del fabbricante Remington
Vai alla pagina of 20
REMINGT ON ® POWERHAMMER Model 476 Operating Instructions The Remington Powerhammer is de- signed for use with Remington Powder 22 caliber, Type A crimped loads and Remington Power Fasteners which are no longer than 63.
2 W ARNING: Safety Precautions BEFORE USING 1. ALWAYS handle the tool as if it were loaded. Before starting work, check that the tool is unloaded and the muzzle is clear. NEVER load a tool unless it is going to be used. 2. ALWAYS inspect to make sure the tool is working properly.
3 Safety Precautions DEFECTIVE WARNING POWDER ACTUATED TOOLS IN USE! G 018 G 018.
4 Safety Precautions HANDLING THE TOOL 1. NEVER place your hand over the muzzle. Accidental discharge can cause serious injury. 2. ALWAYS store UNLOADED pow- der actuated tool and loads in a locked container. Keep powder loads of different power levels in separate containers.
5 Safety Precautions PO W D ER LO A DS PO W D LO AD G 018 G 018 G 018 G 018 G 018.
6 3 . NEVER make fastenings in spalled or cracked areas. Safety Precautions KNOW YOUR FASTENING BASE MATERIAL 1. ALWAYS know the thickness and type of base material into which you are fastening. NEVER GUESS . Test the base material by using the Center Punch Test.
7 Safety Precautions ? ? ? ? CENTER PUNCH TEST Sinks in with average hammer blow TOO SOFT TOO HARD Point flattens Surface shatters Start 3 GREEN 2 BROWN 4 YELLOW CAST IRON GLASS TILE BRICK 1 GRAY TOO .
8 Safety Precautions 4. NEVER drive fasteners into thin or easily penetrated materials unless it is backed by concrete or steel. When in doubt, such as when base material is concealed, conduct a Center Punch Test. Check continu- ally to avoid fastening into unsuit- able material, especially in older buildings.
9 Safety Precautions 1” TOO THIN WELD 1/2” NO YES G 018 G 018 G 018 G 018 76 mm 3" 3X 1X 76mm 3" 76mm 3" 76mm 3" 5 mm MIN 3/16" 25 mm 1" 13 mm 1/2".
10 OPERATING THE TOOL 1. ALWAYS hold tool perpendicular to work surface. 2. Should the tool fail to fire, hold the muzzle firmly against the work sur- face for 30 seconds. Then remove the tool, eject the load and safely discard the misfired load into water or oil.
11 GAS LINE GASOLINE 482-49 POWDER LOADS 482-51 PO W DER LO ADS Safety Precautions 90 ° 30 WATER Spall Shield G 018 G 018 G 018 G 018 G 018.
12 6. Fasteners are a permanently in- stalled fixture. An act of demolition is required for their removal. Appro- priate safety precautions must be taken. Safety Precautions 2. Remington Powder Loads are available in four power levels with gray (1) being the lowest power level and yellow (4) being the high- est power level.
13 PO W D ER LO A DS 482-54 POWDER LOADS 482-55 YELLOW? BROWN ? GREEN ? GRAY ? NOTE: Failure to start with the lowest power level can result in overdrive condition and will result in damage to tool.
14 Safety Precautions 7. NEVER use fasteners longer than 63.5mm (2 1/2”). NEVER use com- mon nails. Remington Power Fas- teners are manufactured from spe- cial steel and heat treated to pro- duce a very hard, yet ductile fas- tener. 8. NEVER pry a load out of the cham- ber.
15 Safety Precautions Overdriven Fasteners An overdriven fastener results when too strong of a powder load is used causing the piston to extend past the muzzle. Move to the next lightest powder load. Repeated overdrive will damage your tool. By avoiding overdrive, you can ex- tend the life of your tool considerably.
16 LOADING THE POWERHAMMER 1. Insert the proper fastener into the muzzle, round metal head first. Push fastener until the point is even with the end of the muzzle. 2. Grab the muzzle and pull forward until it stops. This sets the piston and opens the chamber area.
17 Operation Spring Must Be Compressed Firing Pin Line Up Grooves Muzzle Firing Pin Grip Barrel Chamber LOADING FIRING EJECTING Continued.
18 CARE OF YOUR POWERHAMMER Clean your Powerhammer after each day’s use. Clean chamber with acces- sory wire brush, part number 56485. Apply good quality penetrating lubricant spray (such as WD-40) sparingly and wipe dry.
19 Limited W arranty DESA International warrants this Remington Model 476 POWERHAMMER against defects in materials and workmanship for a period of 30 days from the date of purchase.
101915-01 Rev. B 8/96 IMPORTANT This tool is designed to use Remington 22 caliber neck-down crimped loads, power levels 1 (gray) through 4 (yellow). Straight Wadded Power Load Neck-Down Crimped Power Load NOTICE: This is your Owner’s Manual. Read Carefully before operating your Remington POWERHAMMER Accessories Part No.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Remington 476 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Remington 476 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Remington 476 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Remington 476 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Remington 476, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Remington 476.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Remington 476. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Remington 476 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
