Manuale d’uso / di manutenzione del prodotto C1306M-B (10/06) del fabbricante Pelco
Vai alla pagina of 24
ExSite ™ EHXM Series Explosionproof Fixed Sy stem INSTALLATION C1306M-B (10/06).
2 C1306M-B (10/06) Contents List of Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safe ty Instruct ions .
C1306M-B (10/06) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed al l warnings. 4. Follow all instructions. 5. Do not bl ock any venti lation open ings. Install in accordance with the manufact urer’ s instructions.
4 C1306M-B (10/06) Getting Started Thank you fo r purchasin g Pelco’ s ExSite ™ EHXM Series explosionproof system. This ma nual incl udes instructions f or installing all the compon ents of the system.
C1306M-B (10/06) 5 Install the Power Module Attach the power module to the mo unting surface. Use only insta llation methods and materials capa ble of supporting fou r times t he maximum specified load o f the system (140 lb /63.
6 C1306M-B (10/06) CONNECT WIRING Refer to the following informa tion to connect the wires an d cables as required. NOTES: • Relay 3 is a llocated specif ically for an external wash er (not su pplied by Pelco ). • All relays are specifie d for 32 VDC, 0.
C1306M-B (10/06) 7 DIP SWITCH SETTINGS Configure the receiver address, termination, and baud se tting for the system. The DIP switches to configure th ese settings are located on the to p of the power module. NOTE: No DIP switch settings are requ ired for Coaxitron control.
8 C1306M-B (10/06) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 1 OFF OFF OFF OFF OFF O FF OFF OFF 2 ON OFF OFF OFF OFF OFF OF F OFF 3 OFF ON OFF OFF OFF OFF OF F OFF 4 ON ON.
C1306M-B (10/06) 9 ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 49 ON OFF OF F OFF ON ON OFF OFF 50 OFF ON OFF OFF ON ON OFF OFF 51 ON ON OFF OFF ON ON OFF OFF 52 OFF OFF ON .
10 C1306M-B (10/06) T able B. D Protocol Receiver Address (Continued) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 143 ON ON ON ON OFF OF F OFF ON 144 OFF OFF OFF OFF ON OFF .
C1306M-B (10/06) 11 ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 2 3 9 O NO NO NO N O F F O NO NO N 240 OFF OFF OFF OFF ON ON ON ON 241 ON OFF OFF OFF ON ON ON ON 242 OFF ON .
12 C1306M-B (10/06) Install the Camera Module T o install the camera mo dule, do th e followi ng: 1. Refer to Figure 4. Loosen t he set screw at the back of the camera encl osure with the pr ovided 1.5 mm A llen wrench. Figure 4. Loosen Set Screw 2. Use the supplied spanne r wrench to loosen the ba ck of the camera enclosur e (refer to Figure 5).
C1306M-B (10/06) 13 3. Slide th e camera module i nto the camera enclosure. Refer to Figure 6 to position t he camera modul e properly in the camera e ncl osure. Carefully mate the camer a’ s power connector to the mating connector loca ted inside the camera en closure.
14 C1306M-B (10/06) 4. Models with a wiper: Refer to Figure 8 and do the fo llowing to install the arm of th e wiper: a. Place the su pplied green bushing on t he stud locate d behind th e handle of t he camera module . The bushing should be in the sam e orientatio n as shown in Figure 8.
C1306M-B (10/06) 15 Install the Enclosure and Set Pan Position 1. Check fo r proper seat ing of the po wer module seal. Make sure t he seal is fully seated in t he groove on th e top of the power m odul e. Figure 9. Factory-Installed Power Module Seal 2.
16 C1306M-B (10/06) Set the T ilt Angle of the Camera Module 1. Place a 41 mm open end or crescent wrench on the tilt locking nu t and a 21 mm open end wre nch on the tilt shaft (refer to Fig ure 11).
C1306M-B (10/06) 17 Install the Sun Shroud 1. Place the supplied nylon washer s on the 6-32 Phillips pan head screws. Refer to Figure 12. 2. Align the moun ting holes of the sun shroud with the holes on top of th e camera enclosure. 3. Use the supplied nylo n washers and screws t o secure the sun shroud to th e camera enclosure.
18 C1306M-B (10/06) Maintenance CAMERA MODULE REPLACEMENT T o replace the c amera module, do t he following: 1. Remove the back cap of the came ra enclosure. Refer to Figur e 13 and do the following: a. Loosen the set screw with a 1. 5 mm Allen wrench .
C1306M-B (10/06) 19 3. Models with a wiper: Remove the wiper arm an d the green bushing from the unit (r efer to Figure 14 ). 4. Slide the camera modu le out of the enclosure. 5. Install th e new camera modu le by doing th e following: Slide the came ra module into the camera encl osure.
20 C1306M-B (10/06) 6. Models with a wiper: Refer to Figure 14 and do the following to re install the arm of the wipe r: a. Reinstall the gree n bushing on the stud locate d behind the handle of the camera module.
C1306M-B (10/06) 21 Specifications ELECTRICAL Input Voltage 24 VAC or 100-240 VAC Input V oltage Range ±10% Power Consumptio n Maximum 60 W (120 VA) per system Heater and Defroster Microprocessor con.
22 C1306M-B (10/06) *Manual control of camera setup functio ns can be done with CM6700, CM 6800, CM8500, CM 9500, CM9740 , CM9760, CM9770, CM9780, KBD200A , KBD300A, and MPT95 00 controllers, but not with CM7500, MPT9000 , or KBD9000 cont rollers.
The materials used in the manufacture of this document an d it s components are compliant to the requirements of Directive 2002/9 5/EC. This equipment contains elec trical or electronic components tha.
W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Pelco C1306M-B (10/06) è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Pelco C1306M-B (10/06) - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Pelco C1306M-B (10/06) imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Pelco C1306M-B (10/06) ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Pelco C1306M-B (10/06), ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Pelco C1306M-B (10/06).
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Pelco C1306M-B (10/06). Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Pelco C1306M-B (10/06) insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
