Manuale d’uso / di manutenzione del prodotto 5620-A2-GN11-30 del fabbricante Paradyne
Vai alla pagina of 24
1 Hotwire 5620 RTU Customer Premises Installation Instructions Document Number 5620-A2-GN1 1-30 August 2000 Contents What Does the Hotwire 5620 RTU Do? 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing the DSL Access Wiring 6 .
2 NOTES: In this document: — End-user system is used to represent any host with an Ethernet connection. — Service provider is used to represent any Internet Service Provider (ISP) or remote LAN access provider .
3 DSL Access with a Hotwire 5030 or 5038 POTS Splitter When a Hotwire POTS splitter is used at both ends of the local loop, wiring is connected: From the demarcation point to the CP POTS splitter , and From the demarcation point to the DSL jack.
4 DSL Access with a Hotwire 5038 Distributed POTS Splitter When a Hotwire 5038 Distributed POTS Splitter is used, one 5038 Distributed POTS Splitter is installed as a phone filter for each telephone on the same POTS line as DSL.
5 Package Checklist V erify that your package contains the following: Model 5620 Remote T ermination Unit (RTU) DSL interface cable with RJ1 1 modular plugs Power cord with power transform.
6 Installing the DSL Access Wiring The local loop terminates at the punchdown block or NID. Wiring must be connected from the customer premises side of the punchdown block or the NID to an RJ1 1 jack. T ypically , the punchdown block is installed in commercial locations and the NID is installed in residential locations.
7 3. Locate the DSL pair of T1/R1 connectors on the customer premises side of the NID or punchdown block. Attach the wiring that will be connected to the DSL jack. In the following example, a NID is used without a POTS splitter . It includes an existing POTS line and a second pair installed for DSL access.
97-15300a RJ11 W all Jack or 8 Connecting to the DSL Access Wiring The Hotwire 5620 RTU connects to the local loop via wiring from the demarcation point to an RJ1 1 wall jack. The DSL twisted-pair wiring from the local loop terminates at a new or existing wall jack.
9 Installing the Hotwire 5620 R TU Place the Hotwire 5620 RTU on a flat surface with clearance for the rear connectors. Procedur e 1. Use the supplied RJ1 1 6-pin interface cable for the DSL connection. Insert one end of the cable into the jack labeled DSL.
10 2. Use an 8-pin Ethernet cable for the Ethernet connection. Insert one end of the cable into the jack labeled ETHERNET . Use a straight-through cable to connect the other end to an Ethernet hub. Do not connect to the optional Uplink connection with a straight-through cable (requires an Ethernet crossover cable).
11 3. Insert the supplied power cord’s round end into the jack labeled POWER. Plug the transformer into an AC outlet. 98-15836 PO WER ETHERNET DSL Hotwire RTU Po w e r Jack or T ransformer or The RTU hardware installation is now complete. When the power cord is installed, the RTU goes through a power-on self-test.
12 Status LEDs All of the LEDs turn on and off during the power-on self-test. After a successful self-test, the LEDs should appear as indicated in BOLD in the Condition column below . LED Condition Status PWR ON The RTU has power . ALM OFF ON No active alarms.
13 T roubleshooting LED Symptom Action All LEDs are on. If the LEDs remain on for more than ten minutes, the RTU is not functional. Unplug the unit and reapply power . If the ALM LED is still on, contact the service provider . ALM LED remains on. The power-on self-test may have failed.
98-15304-01 6-Pin RJ11 Plug DSL Cable Pin #1 Pin #6 14 Increasing the Number of End-User Systems A single end-user system is attached to the Hotwire 5620 RTU by using an Ethernet crossover cable. T o increase the number of end-user systems, connect all end-user systems to an Ethernet hub using a straight-through cable.
98-16055a 8-Pin Plug Ethernet Cable Pin #1 Pin #8 15 Ethernet interface connector uses an 8-pin, non-keyed modular plug. Use shielded twisted-pair CA T5 or better cables.
16 Optional R TU W all Placement The Hotwire 5620 RTU is designed for tabletop placement. The R TU can also be mounted on a wall. T o mount an RTU, you will need: - Three slotted-head #6 self-threadin.
17 R TU Hardware T emplate F ront (LEDs) 98-16171 5.43" 7.55" T o Bottom Hole.
18 Technical Specifications for Model 5620 R TU Item Specification * Height x Width x Depth 1.25 ″ x 6.00 ″ x 8.75 ″ (3.18 cm x 15.24 cm x 22.23 cm) Weight 1 lb.
19 ! Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. T o ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered.
20 CE Marking When the product is marked with the CE mark on the equipment label, this demonstrates full compliance with the following European Directives: Directive 73/23/EEC – Council Directiv.
21 Declaration of Conformity This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2 and 15 of the Federal Communications Commission’s Rules. This compliance information statement pertains to the following products: T rade Name: Hotwire Model Number: 5620-A3-200 This device complies with Part 15 of the FCC Rules.
22 Government Requirements Certain governments require that instructions pertaining to connection to the telephone network be included in the installation and operation manual. Specific instructions are listed in the following sections. United States – Notice to Users of the T elephone Network 1.
23 7. The user is not authorized to repair or modify the equipment. 8. This equipment cannot be used on public coin service provided by the telephone company . Connection to Party Line Service is subject to state tariffs. (Contact the state public utility commission, public service commission or corporation commission for information.
24 W arranty , Sales, Service, and T raining Information Contact your local sales representative, service representative, or distributor directly for any help needed.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Paradyne 5620-A2-GN11-30 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Paradyne 5620-A2-GN11-30 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Paradyne 5620-A2-GN11-30 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Paradyne 5620-A2-GN11-30 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Paradyne 5620-A2-GN11-30, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Paradyne 5620-A2-GN11-30.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Paradyne 5620-A2-GN11-30. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Paradyne 5620-A2-GN11-30 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
