Manuale d’uso / di manutenzione del prodotto Wireless Ethernet Systems del fabbricante Microtek
Vai alla pagina of 27
OPERA TIONS MANUAL MiniLink® Wireless Ethernet Systems MicroTek Electronics, Inc. 25691 Atlantic Ocean Drive, Suit e B-3; Lake Forest, CA 92630 Information Hotline 888-36-MICRO www.
IMPORTANT SAFETY INSTRUCTION For your protection, please read and obser ve all safety instructions before operati ng this system and keep this s heet and any additional instructions for future referen ce. INSTALLATION & USE OBSERVE WARNINGS: All warnings in the operating instru ctions should be carefully followed.
FCC Output Power Restrictions The FCC does not require licensing to implem ent this device. License-free oper ation in the industrial, scientif ic, and medical band is documented in FCC Rules Part 15.
FCC REGULATORY ALERT Regulatory Alert As of July 20, 2007, a new FCC regulation has gone into effect which impacts operators of the U-NII band in the United States. As a result of this regulatory ch ange, several MicroTek products are affected. The new FCC regulation impacts the sale of wireless equipment in the 5.
I NDEX S E C T I O N P A G E # IMPORTANT SAFETY INSTRUCTIONS, FCC NOTICE ---------------- ( i ) RADIO FREQUENCY EXPOSURE, INDUSTRY CANADA ------------- ( ii ) IMPORTANT FCC REGULATORY NOTICE----------.
Q UICK S TA R T P ROCEDURES MicroTek Electronics, Inc. recommends that all equipment be bench tested before being installed onsite. This test will ensure the equipmen t is functioning properly. IMPORTANT: SEE NEW FCC REGULATORY ALERT ON PAGE “( iii )” W IRELESS E THERNET M ODULE S ETUP 1.
P RE -I NSTALLATION R EMINDERS The information on the Quick Start Guide is inte nded for ease of use and a pplication, the following reminders will help to ensure your satisfaction with MicroTek products and service. 1. Read through this manual before bench testing and installation 2.
M INI L INK W IRELESS E THERNET S YSTEM (WES) The MiniLink WES is a plug and play CAT5/Etherne t cable replacement device. It operates in the 5.8 GHz U-NII bands on 5 non-overlapping channels .
POWER INJECTION MODULE (PIM) Note: The Power Injector Modules are not weatherpr oof units and must be protected from moisture. PIM DESCRIPTION A. TOP VIEW 1. ETHERNET IN – Connect to Ethernet device 2. POWER IN – 12-20 VDC Center Positive 3. ETHERNET OUT – Connect to Host/Client 2 3 1 B.
WES CONNECTION DIAGRAMS The following wiring schemes represent the configurations that have been tested and verified by MicroTek Electronics bas ed on typical Ethernet wiri ng solutions. Other wiri ng configurat ions cou ld be possibl e based on the application.
WEM INSTALLATION & OPERATION (cont’d) B. MOUNT DIRECTIONAL HOST/CLIENT Mount the Host/Client with the included wall/pole mount bracket and hardware. Connect the black mounting assembly with adjustment swivel to mounting L-shaped bracket with the ¼ - 20 button head screw.
WEM INSTALLATION & OPERATION (cont’d) E. CONNECT HOST/CLIENT Connect the cable to the Host/Client. Slide the cable jacket up to the base of the connector. Slide the weatherproof connector over the cable jacket and screw it into the Host/Client and tighten.
B. MULTI-CONNECT SYSTEMS (cont’d) If you ordered a complete system with multiple Client SUs, they have been pr e-configured with IP addresses as follows: ML WES Modules ML WES Serial Number ML WES IP Address Host AP, Client SU or Point to Point Channel Unit 1 05618* 192.
WEB PAGES (cont’d) B. STATUS – DEVICE STATUS 1. POINT-TO-POINT HOST AP The Device Status page provides the details of how the Single-Point Host is configured. The Access Point Name can be changed on the “A dmin” page under the ADVANCED tab but the SSID cannot change.
B. STATUS – DEVICE STATUS (cont’d) 2. MULTI-CONNECT HOST AP The Device Status page provides the details of how the Multipoint Host is configured. 3.
WEB PAGES (cont’d) C. STATUS – HOST/CLIENT ASSOCIATION LISTS 1. POINT-TO-POINT AND MULTI-CONNECT HO ST The Client List page of the Host AP shows the MAC address( s) of the paired or grouped Client SU(s) that are connected to the Host AP. For Point-to-Point systems, one MAC address will be shown.
WEB PAGES (cont’d) D. STATUS – STATISTICS The Statistics page will indicate the number of transmitted and received data packets versus the number of dropped packets.
WEB PAGES (cont’d) E. BASIC - WIRELESS The wireless page is used for enabling S uper mode. The Super mode combines adjacent channels to provide up to 50+ M bps of throughput. The channels available in Super mode are: 4 and 6 only. If another channel is selected, Supe r mode will not be enabled.
F. BASIC – ETHERNET 1. NETWORK SETTINGS The Network Sett ings page is used for changing the IP Address, Subnet Mask and or Default Gateway of the Host or Client.
WEB PAGES (cont’d) G. ADVANCED – ADMINISTRATION This section of the Advanced tab is used for changing the password and other adm inistration services for the Host or Client. H. ADVANCED – SYSTEM To reboot the system and/or bring it to its defau lt settings, visit the system page of the Advanced tab.
WEB PAGES (cont’d) I. ADVANCED – FIRMWARE This page is used to flash firmware upgrades should it be necessary to do so. - 17 -.
SYSTEM INSTALLATION NOTES A. SYSTEM LOCATION 1. Address: _________________________________________________________ 2. Contact: _________________________________________________________ 3. Phone Number: ___________________________________________________ B.
WEM SPECIFICATIONS RF Modules RF SECTION Power Output 50 W EIRP @ 5.8 GHz (maxim um) Transmitting Frequency 5.725 – 5.825 GHz (U-NII-3 / ISM) Channel Capacity 5 non-overlapping channels 5.
WEM SPECIFICATIONS (cont’d) Power Injection Module MECHANICAL Physical Plastic housing, not weatherproof Dimensions 2.6” x 2.6” x 1.1” Weight 2.
T ROUBLE S HOOTING PROBLEM SUGGESTION No Link Activity 1. No power from connected device–make sure the connected Ethernet/IP device is powered. 2. Check all cables and connectors. If the tester shows that all wires are making contact, check the entire length of cable for kinks, cuts, tears or any other cable hindrances.
FA Q Q. Which unit is the transmitter and which is the receiver? A. WES systems are bi-directional so it is not critical which of the units is mounted at the receive location (and vice-versa). Typically, however, the ‘H ost’ is located at the receive end and the ‘Client’ is at the transmit location.
W ARRANTY I NFORMA TION MicroTek Electronics extends the following LIMITED W ARRANTY to the original owner/purchaser of this product as follows: - Two years from the date of initial sale for all wireless products. - One year from the date of initial sale for all encoder and decoder products.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Microtek Wireless Ethernet Systems è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Microtek Wireless Ethernet Systems - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Microtek Wireless Ethernet Systems imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Microtek Wireless Ethernet Systems ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Microtek Wireless Ethernet Systems, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Microtek Wireless Ethernet Systems.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Microtek Wireless Ethernet Systems. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Microtek Wireless Ethernet Systems insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
