Manuale d’uso / di manutenzione del prodotto MiniLink del fabbricante Microtek
Vai alla pagina of 25
OPERA TIONS MANUAL MiniLink® Wireless Ethernet Systems MicroTek Electronics, Inc. 25691 Atlantic Ocean Drive, Suit e B-3; Lake Forest, CA 92630 Information Hotline 888-36-MICRO www.
IMPORTANT SAFETY INSTRUCTION For your protection, please read and obser ve all safety instructions before operati ng this system and keep this sheet and any additional instructions for future re ference. INSTALLATION & USE OBSERVE WARNINGS: All warnings in the operating instru ctions should be carefully follo wed.
FCC Output Power Restrictions The FCC does not require licensing to implem ent this device. License-free oper ation in the industrial, scientif ic, and medical band is documented in FCC Rules Part 15.
I NDEX S E C T I O N P A G E # IMPORTANT SAFETY INSTRUCTIONS, FCC NOTICE ---------------- ( i ) RADIO FREQUENCY EXPOSURE, INDUSTRY CANADA ------------- ( ii ) QUICK START GUIDE -----------------------.
Q UICK S TA R T G UIDE MicroTek Electronics, Inc. recommends that all equipment be bench tested before being installed onsite. This test will ensure the equipment is functioning properly. W IRELESS E THERNET M ODULE (WEM) S ETUP 1. Remove the WEMs from box, select frequency via th e rotary switch at the sid e of the unit.
P RE -I NSTALLATION R EMINDERS The information on the Quick Start Guide is inte nded for ease of use and a pplication, the following reminders will help to ensure your satisfaction with MicroTek products and service. 1. Read through this manual before bench testing and installation 2.
M INI L INK W IRELESS E THERNET S YSTEM (WES) The MiniLink WES is a plug and play CAT5/Ethernet cable replacement device. It operates in the 5.3 and 5.
C. SIDE VIEW (cont’d) 2. ETHERNET PORT Standard RJ-4 5 connector. 3. ROTARY CHANNEL SELECT SWITCH Shows switch settings for channels 0 – 9. *Note: Channels 0, 1 and 2 are the same frequency. If two or more systems are in use and either channel 0, 1 or 2 are used on the first system, the following systems must be set to channel 3 or higher.
WES CONNECTION DIAGRAM The following wiri n g schem es represent the con fig urat i o ns that have been te sted and veri fied by MicroT ek Electronics ba sed on t ypical Et hernet wirin g solutions. Other wi ring con figurations c ould be possible bas ed on the application.
WEM INSTALLATION & OPERATION (cont’d) B. MOUNT DIRECTIONAL WEM Mount the WEM with the included wall/pole mount bracket and hardware. Connect the mounting block with ball adjustment to mounting br acket with the ¼ - 20 button head screw. Connect the WEM to the mounting block using the ¼-20 mounting holes in the WEM.
WEM INSTALLATION & OPERATION (cont’d) E. CONNECT WEM Connect the cable to the WEM. S lide the cable jacket up to the base of the connector. Slide the weatherproof connector over the cable jacket and screw it into the WEM and tighten. Tighten the clamping nut until the CAT5 cable is sealed in the connector.
B. MULTI-CONNECT SYSTEMS (cont’d) Administration Page (Section E below) manually . If you ordered a complete system with multiple Client SU WEMs, they have been pre-configured with IP addresses as follows: Client SU WEM Serial Number IP Address Unit 1 00511* 192.
WEB PAGES (cont’d) B. INFORMATION 1. POINT-TO-POINT HOST AP WEM The information page provides the details of how the Single-Point Host WEM is configured.
A. INFORMATION (cont’d) 2. MULTI-CONNECT HOST AP WEM The information page provides the details of how the Multipoint Host WEM is configured. 3. CLIENT SU WEM The information page provides the details of how the Client WEM is configured.
WEB PAGES (cont’d) C. STATIONS/APs 1. POINT-TO-POINT AND MULTI-CONNECT H O ST AP WEMS The Stations/Associations page of the Host AP WEM shows the MAC address(s) of the paired or grouped Client SU WEM(s) the Host AP WEM is connected to. For Point-to-Point systems, one WEM MAC address will be shown.
WEB PAGES (cont’d) D. WIRELESS The wireless page is used for enabling S uper mode. The Super mode combines adjacent channels to provide up to 50+ Mbps of throughp ut. The channels available in Super mode are: 3, 6 and 8 only. If another channel is selected, Supe r mode will not be enabled.
D. SECURITY (cont’d) 2. WEP CONFIGURATION The security page is used for enabling WEP encryption and setting the parameters for WEP encryption. Click the “Enable WEP” check box to enable (The WPA configuration will be automatically disabled).
WEB PAGES (cont’d) F. ADMINISTRATION This section of the Administration page is used for rebooting t he WEM, resetting the default configuration and/or upgrading/uploadin g the firmware in the system. Contact MicroTek to obtain the files for a firmware upgrade.
E. ADMINISTRATION (cont’d) This section of the Administration page is u sed for selecting the device name, changing IP settings and changing the user name and password needed to access the system. NOTE: The Device name on t he Admin pa ge of a HOST AP will be “MicroTek Host AP”.
SYSTEM INSTALLATION NOTES A. SYSTEM LOCATION 1. Address: _________________________________________________________ 2. Contact: _________________________________________________________ 3. Phone Number: ___________________________________________________ B.
WEM SPECIFICATIONS RF Modules RF SECTION Power Output 1 W EIRP @ 5.3 GHz (maximum) 50 W EIRP @ 5.8 GHz (maximum) Transmitting Frequency 5.25 0 – 5.350 GHz (U-NII-2) 5.725 – 5.825 GHz (U-NII-3 / ISM) Channel Capacity 8 non-overlapping channels 5.3 GHz Band - 5280, 5300, 5320 5.
WEM SPECIFICATIONS (cont’d) Power Injection Module MECHANICAL Physical Plastic housing, not weatherproof Dimensions 2.6” x 2.6” x 1.1” Weight 2.
T ROUBLE S HOOTING PROBLEM SUGGESTION No Link Activity 1. NO POWER – make certain both WEMs have power and the red Power LED is on. Make sure the connected Ethernet/IP device is powered. 2. Check the configuration of all WEMs. Each pair and/or all groups of WEMs setup to communicate with each other must be set to the same channel.
FA Q Q. Which unit is the transmitter and which is the receiver? A. WES systems are bi-directional so it is not crucial which of the units is mounted at the receive location (and vice-versa), however, typically the ‘host’ is the receiver and the ‘client’ is the transmitter.
W ARRANTY I NFORMA TION M ICRO T EK L IMITED W ARRANTY MicroTek Electronics extends the follo wing LIMITED WARRANTY to the original owner/purchaser of this product: 1) If, within two years after date .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Microtek MiniLink è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Microtek MiniLink - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Microtek MiniLink imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Microtek MiniLink ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Microtek MiniLink, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Microtek MiniLink.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Microtek MiniLink. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Microtek MiniLink insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
