Manuale d’uso / di manutenzione del prodotto M570TU del fabbricante Intel
Vai alla pagina of 100
.
.
Preface I Preface Notebook Computer M570TU Service Manual.
Preface II Preface Notice The company reserves the right to revise this publication or to change its conten ts without notice. In formation contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent ven- dor.
Preface III Preface About this Manual This manual is intended for service pe rsonnel who have completed sufficient training to undertake the maintenance and inspection of personal computers. It is organized to allow you to look up basic informat ion for servicing and/or upgr ading components of the M570TU se- ries notebook PC.
Preface IV Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including t hose listed below, to reduce the risk of fire, electric shock and injury to per- sons when using any electrical equipment: 1.
Preface V Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifi cations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Preface VI Preface FCC RF Radiation Exposure Statement: 1. This T ransmitter must not be co-located or operatin g in conjun ction with any oth er antenna or tr ansmitter . 2. This equipment complies with F CC RF radiation exposure limit s set forth for an uncontrolled environme nt.
Preface VII Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: 1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Preface VIII Preface 4. A void interference. Keep the computer awa y from high capacity trans formers, electric motors, and other strong mag- netic fields. These can hinder proper p erformance and damage you r data. 5. T ake care when using peripheral devices .
Preface IX Preface Battery Precautions • Only use batteries designed for this co mputer . The wrong battery type may expl ode, leak or damage the computer . • Do not remove any batteries from the computer while it is powere d on. • Do not continue to use a battery that has be en dropped, or that appears damaged (e.
Preface X Preface Related Documents You may also need to consult the foll owing manual for addi tional information: User’s Manual on CD This describes the notebook PC’s features and the procedures for operating the computer and its RO M-based setup pro- gram.
Preface XI Preface Contents Introduction .............................................. 1-1 Overview ......................................................................................... 1-1 System Specifica tions .................................
Preface XII Preface CARD READER & 1394 JMB380 .............................................. B-21 NEW CARD ................................................................................. B-22 KBC-ITE IT8512 ......................................
Introduction Overview 1 - 1 1.Introduction 1: Introduction Overview This manual covers the information you need to service or upgrade the M570TU series notebook computer. Information about operating the computer (e .g. getting started, and the Setup utility) is in the User’s Manual .
Introduction 1 - 2 System Specifications 1.Introduction System Specifications Feature Spe cification Processor T ypes Intel® Core™2 Duo Processor (478-pin) Micro-FC-PGA Packag e, 25W P8400 / P8600 45nm (45 Nanometer) Process T echnology 3MB On-die L2 Cache & 1066MHz FSB 2.
Introduction System Specifications 1 - 3 1.Introduction Video Card Options NVIDIA GeForce 8800M G TX PCI-E Video Card MXM-III 512MB GDDR3 Video RAM On Board MS DirectX® 10.0 Compatible Supports HDCP NVIDIA GeForce 9800M G TX PCI-E Video Card MXM-III 512MB GDDR3 Video RAM On Board MS DirectX® 10.
Introduction 1 - 4 System Specifications 1.Introduction Mini-Card Slot s One Mini-C ard Slot for Wireless LAN Module One Mini-C ard Slot for TV T uner Module One Mini-C ard Slot for Intel T u rbo Memory Module Power Management Supports ACPI 3.0 Communication Built-In 56K MDC Modem w ith V .
Introduction External Locator - Top View with LCD Panel Open 1 - 5 1.Introduction External Locator - Top View with LCD Panel Open Figure 1 Top View 1. Optional Built-In PC Camera 2. LCD 3. Hot Key Buttons 4. Power Button 5. Keyboard 6. T ouchPad and Buttons 7.
Introduction 1 - 6 External Locator - Front & Rear View 1.Introduction External Locator - Front & Rear View Figure 2 Front & Rear Views 1. LCD Latches 2. Line-In Jack 3. Headph one-Out Jack 4. Microphone-In Jack 5. S/PDIF-Out Jack 6. LED Indicators 7.
Introduction External Locator - Righ t & Left Side View 1 - 7 1.Introduction External Locator - Right & Left Side View 1 2 3 4 5 6 7 3 8 Right Figure 3 Right & Left Side View 1. ExpressCard/ 54(34) Slot 2. 7-in-1 Card Reader 3. 2 * USB 2.0 Port s 4.
Introduction 1 - 8 External Locator - Bottom View 1.Introduction External Locator - Bottom View Figure 4 Bottom View 1. V ent 2. Battery 3. Battery Release Latch 4. Optical Device Release Latches 5. Component Ba y Cover 6. Consumer Infrared T ransceiver 7.
Introduction Mainboard Overview - Top (Key Parts) 1 - 9 1.Introduction Mainboard Overview - Top (Key Parts) Figure 5 Mainboard Top Key Parts 1. ITE IT8512E 2.
Introduction 1 - 10 Mainboard Overview - Bottom (Key Parts) 1.Introduction Mainboard Overview - Bottom (Key Parts) Figure 6 Mainboard Bottom Key Parts 1. CPU Socket (no CPU installed) 2. North Bridge 3. VGA Socket 4. Azalia Codec ALC 662 5. Audio Amp.
Introduction Mainboard Overview - Top (Connectors) 1 - 11 1.Introduction Mainboard Overview - Top (Connectors) Figure 7 Mainboard Top Connectors 1. LED Cable Connector 2. CCD Cable Connector 3. Inverter Board Cable Connector 4. S peaker-lef t Cable Connector 5.
Introduction 1 - 12 Mainboard Overview - Bottom (Connectors) 1.Introduction Mainboard Overview - Bottom (Connectors) Figure 8 Mainboard Bottom Connectors 1. HDMI Port 2. DVI-Out Port 3. Combined eSA T A/ USB Port 4. DC-In Jack 5. Battery Connector 6. LCDS Cable Connector 7.
Disassembly Overview 2 - 1 2.Disassembly 2: Disassembly Overview This chapter provides step-by-step instructions for disassembling the M570TU series notebook’s part s and subsystems. When it comes to reassembly, reverse the procedures (unless ot herwise indicated).
Disassembly 2 - 2 Overview 2.Disassembly NOTE : All disassembly procedures assume that the system is turned OFF , and disconnected from any power supply (the battery is removed too). Maintenance Tools The following tools are recommende d when working on the notebook PC: • M3 Philips-head screwdriver • M2.
Disassembly Overview 2 - 3 2.Disassembly Maintenance Precautions The following precautions are a reminder. To avoid personal injury or damage to the computer while performing a re- moval and/or replacement job, take the following precautions: 1. Don't drop it .
Disassembly 2 - 4 Disassembly Steps 2.Disassembly Disassembly Steps The following table lists the disa ssembly steps, and on which page to find the related information. PLEASE PERFORM THE DISASSEMBLY STEPS IN THE ORDER INDICATED. To remove the Battery: 1.
Disassembly Disassembly Steps 2 - 5 2.Disassembly 6. Remove the VGA Card page 2 - 13 7. Remove the WLAN module page 2 - 15 8. Remove the TV T uner Card page 2 - 16 9. Remove the Bluetooth Module page 2 - 18 10. Remove the keyboard page 2 - 19 1 1. Remove the Modem page 2 - 20 To remove the Inverter Board: 1.
Disassembly 2 - 6 Removing the Battery 2.Disassembly Removing the Battery 1. Tu rn the computer off, an d turn it over . 2. Slide latch towards the unlock symbol and hold it in place, and lif t the battery up and out of the battery bay . 2. Battery 1 2 Figure 1 Battery Removal a.
Disassembly Removing the Hard Disk Drive 2 - 7 2.Disassembly Removing the Hard Disk Drive The hard disk drive is mounted in a re movable case and can be take n out to accommodate othe r 2.5" serial (SATA) hard disk drives with a height of 9.5mm (h).
Disassembly 2 - 8 Removing the Hard Disk Drive 2.Disassembly 5. Remove screws - from the hard disk cover . 6. Slide the hard disk assembly in the direction of the arrow . 7. Carefully remove the hard disk assembly in the direction of the arrow ( Figure 3d ) .
Disassembly Removing the Optical (CD/DVD) Device 2 - 9 2.Disassembly Removing the Optical (CD/DVD) Device 1. Turn off the computer , turn it over and remove the battery ( page 2 - 6 ).
Disassembly 2 - 10 Removing the System Memory (RAM) 2.Disassembly Removing the System Memory (RAM) The computer has two memory sockets for 204 pin Small Outline Dual In-lin e Memory Modules (SO-DIMM) supporting DDRII (DDR3) Up to 800/1066 MHz. The main memory can be expanded up to 4GB.
Disassembly Removing and Installing the Processor 2 - 11 2.Disassembly Removing and Installing the Processor Processor Removal Procedure 1. Turn off the computer , turn it over and remove the battery ( page 2 - 6 ) and the component bay cover ( page 2 - 7 ).
Disassembly 2 - 12 Removing and Installing the Processor 2.Disassembly 5. Tu rn the release latch towards the unlock symbol to release the CPU. 6. Carefully (it may be hot) lift the CPU up and out of the socket ( Figure 7e ). C D Figure 7 Processor Removal (cont’d) d.
Disassembly Removing and Installing the Processor 2 - 13 2.Disassembly Processor Installation Procedure 1. Insert the CPU , pay careful attention to the pin alignment, it will fit only one way (DO NOT FORCE IT!), and turn the release latch towards the lock symbol ( Figure 8b ).
Disassembly 2 - 14 Removing the VGA Card 2.Disassembly Removing the VGA Card 1. Tu rn off the computer , turn it over and remove the ba ttery ( page 2 - 6 ), and the co mponent b ay cover ( page 2 - 7 ). 2. The VGA card(s) will be visi ble at point on the mainboard.
Disassembly Removing the Wireless LAN Module 2 - 15 2.Disassembly Removing the Wireless LAN Module 1. Turn off the computer , turn it over and remove the battery ( page 2 - 6 ) and the component bay cover ( page 2 - 7 ). 2. The Wireless LAN module will be visible at point on the mainboard.
Disassembly 2 - 16 Removing the TV Tuner Card 2.Disassembly Removing the TV Tuner Card 1. Tu rn off the computer , turn it over and remove the battery ( page 2 - 6 ) and the component bay cover ( page 2 - 7 ). 2. The TV T uner card will be visible at point on the mainboard.
Disassembly Removing the Turbo Memory Card 2 - 17 2.Disassembly Removing the Turbo Memory Card 1. Turn off the computer , turn it over and remove the battery ( page 2 - 6 ) and the component bay cover ( page 2 - 7 ). 2. The turbo memory card will be visible at point on the mainboard.
Disassembly 2 - 18 Removing the Bluetooth Module 2.Disassembly Removing the Bluetooth Module 1. Tu rn off the computer , turn it over , and remove the battery ( page 2 - 6 ) and th e component bay cover ( page 2 - 7 ). 2. The Bluetooth module will be visible at point on the mainboard.
Disassembly Removing the Keyboard 2 - 19 2.Disassembly Removing the Keyboard 1. Turn off the computer , and remove the battery ( page 2 - 6 ). 2. Press the five keyboard latches at the top of the keyboard to e levate the keyboard from its normal position (you may need to use a small screwdriver to do this).
Disassembly 2 - 20 Removing the Modem 2.Disassembly Removing the Modem 1. Tu rn off the computer , turn it over and remo ve the battery ( page 2 - 6 ), hard disk ( page 2 - 7 ), optical device ( page .
Disassembly Removing the Modem 2 - 21 2.Disassembly 6. Carefully lift the top case ( Figure 16e ) up and of f the computer . 7. Remove screws - from the mainboard. 8. Lift the mainboard ( Figure 16g ) up and of f the bottom case and turn over the mainboard.
Disassembly 2 - 22 Removing the Inverter Board 2.Disassembly Removing the Inverter Board 1. Tu rn off the computer , and remove the battery ( page 2 - 6 ). 2. Remove any rubber covers, screws - ( Figure 17 a ), then run your finger around the middle of the frame to carefully unsnap the LCD front p anel module from the back.
Part Lists A-1 A.Part Lists Appendix A:Part Lists This appendix breaks down the M570TU series notebook’s constructi on into a series of illust rations. The component part numbers are indicated in the tables opposite the drawings. Note: This section indicates the manufacturer’s part numbers.
Part Lists A - 2 Part List Illustration Location A.Part Lists Part List Illustration Location The following table indicates where to fi nd the appropriate part list illustration.
Part Lists Top with Fingerprint A - 3 A.Part Lists Top with Fingerprint Figure A - 1 Top with Finger- print 無鉛 無鉛 無鉛 (減肉) 無鉛 無鉛 無鉛 無鉛 無鉛 黑 無鉛 無鉛 無鉛 .
Part Lists A - 4 Top without Fingerprint A.Part Lists Top without Fingerprint 無鉛 無鉛 無鉛 (減肉)無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 無鉛 鴻富 無鉛 鴻富 .
Part Lists Bottom A - 5 A.Part Lists Bottom Figure A - 3 Bottom 無鉛 無鉛 無鉛 無鉛 無鉛 藍天3 互億 無鉛 無鉛 無鉛 Ω 無鉛 Ω 無鉛 無鉛 無鉛 無鉛 同美 無鉛 無鉛 無.
Part Lists A - 6 LCD A.Part Lists LCD Figure A - 4 LCD 中性 (變更鋁箔 無鉛 銀 無鉛 (色號701)(無鉛) (墊高 0.5MM) 無鉛 無鉛 無鉛 無鉛 無鉛(增加破孔) (墊高 0.
Part Lists DVD Combo Drive A - 7 A.Part Lists DVD Combo Drive 無鉛 無鉛 軌道 處加肉 無鉛 無鉛 Figure A - 5 DVD Combo Drive.
Part Lists A - 8 DVD Super-Multi Drive A.Part Lists DVD Super-Multi Drive 無鉛 無鉛 軌道 處加肉 無鉛 無鉛 無鉛 Figure A - 6 DVD Super-Multi Drive.
Schematic Diagrams B-1 B.Schematic Diagrams Appendix B:Schematic Diagrams This appendix has circ uit diagrams of the M570TU notebook’s PCB’s. The following ta ble indicates where to find the appropriate schematic diagram.
Schematic Diagrams B - 2 SYSTEM BLOCK DIAGRAM B.Schematic Diagrams SYSTEM BLOCK DIAGRAM Sheet 1 of 42 SYSTEM BLOCK DIAGRAM EC SM BUS PR OCESSOR 10 MHz A P A2 05 6 478 u FCPGA BT SY S5V ,SY S3V ,VD D3,V DD5 ,3V ,5V NORTH BR IDGE CLOCK GEN. MDC CO NN. DDR 3 SD RAM SO CKE T AUD IO AMP .
Schematic Diagrams Penryn 1/2 B - 3 B.Schematic Diagrams Penryn 1/2 3. 3V S V _ T HRM 1. 05VS 1. 05VS 3. 3 V VD D3 CP U_ G T L R E F 2 CL K_ CP U_ BC L K # 1 8 H _D #[63: 0] 4 H_ DB S Y # 4 H_ F E RR .
Schematic Diagrams B - 4 Penryn 2/2 B.Schematic Diagrams Penryn 2/2 VC O R E 1. 5 V S VC O R E 1. 05VS _V C C P VCO RE VC O R E VC OR E VC O R E 1. 05VS _V C C P VC OR E VC OR E VC OR E VCO R E 1. 05 V S 1 .05 VS_ VC CP V_ T HR M 1. 0 5V S 1. 0 5VS CP U_ GT L RE F2 3.
Schematic Diagrams Cantiga 1/5 Host B - 5 B.Schematic Diagrams Cantiga 1/5 Host 1. 05VS 1. 05VS 1. 05VS 1. 05VS 1. 05VS VD D3 H _ DI NV # 3 2 M C H_ BS EL 2 5 H_ R S# 1 2 H _ DS T B N# 0 2 H_ R S# 2 2.
Schematic Diagrams B - 6 Cantiga 2/6 PEG B.Schematic Diagrams Cantiga 2/6 PEG 1. 05 V M 1. 05V M 3. 3V S 1. 5V 3. 3V S 1. 5 V 1. 5V 3. 3V S 3. 3V S 3. 3VS 1.
Schematic Diagrams Cantiga 3/6 DDR B - 7 B.Schematic Diagrams Cantiga 3/6 DDR M_B _D Q [ 63:0] 11 M_A _B S 1# 10 M_B_BS 2# 1 1 M_A _B S 0# 10 M_B_BS 1# 1 1 M_A _B S 2# 10 M _ A _D Q[ 63: 0] 10 M_ B_BS.
Schematic Diagrams B - 8 Crestline 4/6 POWER1 B.Schematic Diagrams Crestline 4/6 POWER1 1.5V 1.05VM 1.05VM VG FX_ C O R E VG FX_ C O R E VG FX_ C O RE VG FX _ C OR E 1.
Schematic Diagrams Cantiga 5/6 GND B - 9 B.Schematic Diagrams Cantiga 5/6 GND Z0 8 0 4 Z0 8 0 5 Z0 8 0 3 Z0 8 0 2 Z0 8 0 1 VSS U2 7I CAN T I GA AU 48 A2 3 AR 48 AL 48 BB4 7 AW 47 AN 47 AJ 47 AF47 AD 4.
Schematic Diagrams B - 10 Cantiga 6/6 POWER2 B.Schematic Diagrams Cantiga 6/6 POWER2 1. 05 V S VC C_ HV 3. 3 V S 1. 05 V M 1. 5V 1. 05 V S VC C_ PE G 1. 05 V M 1. 05 V M 1. 05V M 1. 5 V S 1. 0 5V M 1. 0 5V M 1. 5VS 3. 3VS 1. 0 5 V M 1. 0 5V M 3. 3VS 3.
Schematic Diagrams DDR3 SO-DIMM 0 B - 11 B.Schematic Diagrams DDR3 SO-DIMM 0 VD DSPD 1. 5V 1. 5 V VTT _ M EM 1. 5 V 1. 5 V 3. 3VM VD D SPD VTT _ M EM M_ C K E 0 5 IC H_ SM BCL K0 11 , 1 5, 18 M _ A_ D.
Schematic Diagrams B - 12 DDR3 SO-DIMM 1 B.Schematic Diagrams DDR3 SO-DIMM 1 1. 5V 1. 5V 3. 3VM 1. 5V 1. 5V VD DS PD VTT _ M E M VTT _ M EM M _ B_ R AS# 6 M _ CL K_ DD R 2 # 5 M_ B _ D QS 2 6 ICH _ SM.
Schematic Diagrams LCD,CPU FAN B - 13 B.Schematic Diagrams LCD,CPU FAN PL VD D 3. 3VS 5V S 3. 3 V S PLVDD SY S 1 5 V SY S 15V 3. 3V S 1. 8 VS 1. 8 V S 3.
Schematic Diagrams B - 14 ICH9-M 1/4 S ATA B.Schematic Diagrams ICH9-M 1/4 SATA 3. 3 V S 1. 5V S VDD 3 3. 3V S RT C VCC 3. 3V S 3. 3 V S RT CV CC 5V S 3.
Schematic Diagrams ICH9-M 2/4 PCI,USB B - 15 B.Schematic Diagrams ICH9-M 2/4 PCI,USB 3. 3 V S 3.3 V S 3. 3V 3. 3VM 3. 3 V S 1. 5V S 3. 3 V 3. 3 V M IC H _SPI_ VD D 3.
Schematic Diagrams B - 16 ICH9-M 3/4 CASE FAN B.Schematic Diagrams ICH9-M 3/4 CASE FAN 3. 3 V 3. 3V 3. 3V 3. 3 V S 3. 3V 3. 3 V 3. 3VM 3. 3 V S 5V S 3.
Schematic Diagrams ICH9-M 4/4 B - 17 B.Schematic Diagrams ICH9-M 4/4 5V S 3. 3V S 1 .5 V S_ PCI E_ICH 1. 5 V S 3. 3 V 3. 3V S 3. 3 V 3. 3 V M RT C V CC 5V 1. 0 5 V S 1. 0 5 V S 1. 5V S 1. 5 V S 1. 05V S 3. 3V S 1. 5V S 1. 5 V S 1. 5VS _PC I E_I C H 3.
Schematic Diagrams B - 18 ODD, PC B EEP, USB2.0 & eSATA B.Schematic Diagrams ODD, PC BEEP, USB2.0 & eSATA Sheet 17 of 42 ODD, PC BEEP, USB2.0 & eSATA VC CU S B 0 VC CU SB0 5V VC CU S B 1 V.
Schematic Diagrams CLOCK GENERATOR, CCD B - 19 B.Schematic Diagrams CLOCK GENERATOR, CCD VCC _CC D VCC _CC D 3. 3 V M _ C L K 5V 3. 3 V M 3. 3V M _ C L K 3.
Schematic Diagrams B - 20 PCI-E LAN RTL8 111C B.Schematic Diagrams PCI-E LAN RTL8111C 3. 3V LAN V D D 12 L A N_ A V DD 3 3. 3V L A N_ A V DD 1 2 LA N VD D 12 LAN _V D D 3 L A N_ V D D3 3. 3V S 3. 3 V 3. 3V LA N V D D 1 2 LAN V D D 12 LA N _E V D D 12 L A N_ E V D D1 2 EG ND EG ND 3.
Schematic Diagrams CARD READER & 1394 JMB380 B - 21 B.Schematic Diagrams CARD READER & 1394 JMB380 Sheet 20 of 42 CARD READER & 1394 JMB380 CR _ A GN D CR _ A P VD D 3. 3VS CR _ A P V D D 3. 3VS CR _ A GN D CR _ T AV 3 3 CR _APVD D 3. 3 V S CR _ A GN D 1.
Schematic Diagrams B - 22 NEW CARD B.Schematic Diagrams NEW CARD 1. 5 VS 3. 3V 3.3V S 3. 3V S 3. 3V 3. 3V 1. 5 V S 3.3 V 3. 3 VS 3. 3 V 3.3 V US B _ P P 3 14 NEWCA RD_ CL KRE Q# 18 USB _OC3 # 14 PC I .
Schematic Diagrams KBC-ITE IT8512 B - 23 B.Schematic Diagrams KBC-ITE IT8512 KB C_AG ND 3. 3V S VD D3 KBC _AVDD VD D3 VD D3 VD D3 VDD 3 VD D3 VD D3 VD D3 V DD3 VDD 3 KB C_AG ND VD D3 VD D3 VD D3 SPI_V.
Schematic Diagrams B - 24 HDMI B.Schematic Diagrams HDMI 5V S 5VS_ H DM I 5V S _ H D M I 3. 3VS 3. 3 V S 1. 5V S VD D3 1. 05V S 5V S 5V S _ H D M I 3. 3 V S E X _ H DM I _ HP D 1 5 , 3 7 E X_H D M I _.
Schematic Diagrams LED B - 25 B.Schematic Diagrams LED Sheet 24 of 42 LED 5VS 3. 3VS VD D3 VD D3 5V S L ED _ C AP# 22 LE D _N U M # 22 LED _A C I N # 22 WLA N _ E N 22, 36 LE D _ B AT _FU LL# 22 3.
Schematic Diagrams B - 26 AZALIA CODEC ALC66 2 B.Schematic Diagrams AZALIA CODEC ALC662 Sheet 25 of 42 AZALIA CODEC ALC662 AUD G AUD G 5 VS_ AU D AUD G AU DG 3.
Schematic Diagrams AUDIO AMP B - 27 B.Schematic Diagrams AUDIO AMP AU D G 5V S AU D G AU D G 5V S _AMP 5 VS _A M P 5V S _A MP 5V S AU D G AC 97_VDD A C97_VDD 5V S A UDG AU D G A UDG AU DG AU D G A UDG.
Schematic Diagrams B - 28 SRS B.Schematic Diagrams SRS Sheet 27 of 42 SRS VREFB AU D G AU D G VR EFB AUD G VR EFB 5 VS_ AUD AUD G 5V S _A U D VR EF B AU D G SRS _ L O U T 2 6 SRS _ RO U T 2 6 5 VS_ AU.
Schematic Diagrams CRT, INV, MDC, BT, PWRGD B - 29 B.Schematic Diagrams CRT, INV, MDC, BT, PWRGD 3. 3 V VIN 3. 3 V 3. 3V 3. 3V VCC _ M D C 3. 3 VS 3. 3V 3. 3V VCC _ BT 3. 3 V VIN VIN 5VS 5V S 5V S 3. 3 VS 5VS 5V S 5V S 5V S 3. 3 VS 5V S 3. 3 VS 3. 3 VS VCC_ MD C 1.
Schematic Diagrams B - 30 Power Charger, DC IN B.Schematic Diagrams Power Charger, DC IN Sheet 29 of 42 Power Charger, DC IN VA+ + VD D3 VIN VB VIN VA VD D3 VB VDD 3 3.
Schematic Diagrams Power GPU B - 31 B.Schematic Diagrams Power GPU 3. 3VS VG FX _ C OR E GP U VI N GP U 3. 3 VS 5V 5V 2. 5VS 3. 3 V G PUV CCS ENS E 7 G PUV SSSENS E 7 DF G T _ V R _ EN 5 D F G T_V ID _0 5 D F G T_V I D _1 5 D F G T_V I D _2 5 D F G T_V I D _3 5 D F G T_V I D _4 5 VIN 28 , 2 9, 31, 3 2,33, 34 , 35, 37 3.
Schematic Diagrams B - 32 Power 1.5V/ 0.75V B.Schematic Diagrams Power 1.5V/ 0.75V VIN 5V 5V 5 V VD D Q VD DQ 5V 1.5V VTT_M EM 3.3V VI N V DDQ 3.3V 1.5V SY S15 V 1. 5V S 1.5V_P W RG D1 5 DD_ ON# 34 SU SB L 30 ,32, 33,34 SU SC # 15, 22 SM_ PW ROK 5 1. 5 V 5, 7,9, 10, 11,28 3.
Schematic Diagrams Power 1.8VS/ 1.05VS B - 33 B.Schematic Diagrams Power 1.8VS/ 1.05VS SG N D2 SG N D 1 SG ND 2 SG ND 2 SG ND 1 SG ND 1 SG ND 1 S G ND2 V1.
Schematic Diagrams B - 34 Power 3VS, 5VS, Po wer S/W B.Schematic Diagrams Power 3VS, 5VS, Power S/W VI N VIN 1 VA VD D 3 3. 3 VS VD D 3 5V S VD D 5 SY S3 V SY S15 V S Y S 15V VI N SY S1 5 V VD D 5 3.
Schematic Diagrams Power VDD3/ VDD5/ 3.3V/ 5V B - 35 B.Schematic Diagrams Power VDD3/ VDD5/ 3.3V/ 5V Sheet 34 of 42 Power VDD3/ VDD5/ 3.3V/ 5V SY S1 5 V SY S1 0 V VIN SY S 3 V VD D5 SY S1 5 V LD O 5 V VIN 1 5V VDD 3 S YS5 V SY S5 V SG N D4 SG ND 4 SG N D4 SG ND 4 SG ND 4 SG N D4 SGN D 4 SG ND 4 SYS5V SG ND 4 VD D5 SYS 1 5 V 5V 3.
Schematic Diagrams B - 36 Power VCORE for Penryn CPU B.Schematic Diagrams Power VCORE for Penryn CPU SG ND 3 SG ND 3 S G ND3 SGN D 3 SG N D3 S G ND3 3.
Schematic Diagrams MINI CARD, CIR B - 37 B.Schematic Diagrams MINI CARD, CIR VDD5 3. 3 V 3. 3 V 3. 3 V 1. 5 VS 3. 3 V 3. 3 V 1. 5 VS 1. 5 VS 3. 3 V 3. 3 V WL A N _3 . 3V TV _ G ND 3. 3 V WL A N _ 3. 3V WL A N _3 . 3V WLA N _ 3. 3V WL A N _3 . 3V 1. 5 VS WL A N _1 .
Schematic Diagrams B - 38 MX M PCI -E TYPE-I V B.Schematic Diagrams MXM PCI-E TYPE-IV Sheet 37 of 42 MXM PCI-E TYPE- IV 2. 5 VS VIN 5V S 5V R U N 5V S 3V R U N 3. 3V S 1V 8R U N 3. 3 VS 1. 8V S 3. 3V S 5V S 3. 3 V 2. 5V S 3. 3 V 2. 5 V S 5V R U N VD D 3 1V 8R U N 3V R UN VI N VIN PEG _ RXN[ 0 .
Schematic Diagrams Board to board CON B - 39 B.Schematic Diagrams Board to board CON 5V S VDD3 5V TP 5V 5V S 5V TP 3.3V M_B TN # 3 3 SU S B# 15, 21, 22, 34 TP_C L K 22 TP _D ATA 22 WE B 0# 22, 3 3 WE B 1# 2 2 WE B 2# 2 2 US B _P N10 14 US B _P P10 14 3.
Schematic Diagrams B - 40 BUTTON BOARD B.Schematic Diagrams BUTTON BOARD B+ 3 VH 8 B+ 5 VS BD G N D BD G N D B+ 3 VH 8 B+ 3 VH 8 B+ 3 VH 8 BDG N D BD G N D BD G N D B+ 5 VS BDG ND B+ 3 V H8 BD G ND BD.
Schematic Diagrams CLICK Board B - 41 B.Schematic Diagrams CLICK Board GD GN D G+ 5 V S GD G N D GD GN D GD GN D G+5 V S G+5 V S G+5 V S G+5 V S G3 . 3 V G3 .
Schematic Diagrams B - 42 Fingerprint Board B.Schematic Diagrams Fingerprint Board F3. 3V F3.3V FTC _ V DD FD VD D 1 FA VD D FA VD D FTC_VD D FTC_VD D FTC_VD D FTC_VD D F3.
Schematic Diagrams DEBUG Board B - 43 B.Schematic Diagrams DEBUG Board D+5 V S D+ 5 V S D+ 5 V S D+ 5VS D+ 5 VS D+5 V S D+5 V S D+ 5VS D+ 5 VS D+ 5VS D+ 5 VS D+ 5VS D+ 5 VS D+ 5VS D+ 5VS D+ 5VS D+ 5VS.
Schematic Diagrams B - 44 B.Schematic Diagrams.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Intel M570TU è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Intel M570TU - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Intel M570TU imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Intel M570TU ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Intel M570TU, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Intel M570TU.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Intel M570TU. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Intel M570TU insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
