Manuale d’uso / di manutenzione del prodotto 2812 del fabbricante Hobart
Vai alla pagina of 16
2812 SLICER MODEL 2812 & 2912 SLICERS MODEL 2812PS SLICER . . . with P or tion Scale MODELS 2812 M L-136110 2812PS M L-136114 2912 M L-136111 701 S.
– 2 – T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– 3 – © HOBART, 2004 Installation, Operation, and Care of MODEL 2812 & 2912 SLICERS MODEL 2812PS SLICER with P or tion Scale SA VE THESE INSTR UCTIONS GENERAL The model 2812, 2812PS and 2912 slicers are equipped with a 1 / 2 HP motor and are available for single- phase electrical service.
– 4 – INST ALLA TION UNPACKING Immediately after unpacking the slicer, check for possible shipping damage. If the slicer is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery.
– 5 – OPERA TION SAFETY SAFETY DEVICES INCORPORATED IN THIS SLICER MUST BE IN THEIR CORRECT OPERATING POSITIONS ANYTIME THE SLICER IS IN USE. The T OP K NIFE C OVER must be in position and secured with the L ATCH K NOB (Fig. 2). The R ING G UARD is not removable.
– 6 – The four Preset keys (1 – 4) recall the last-entered portion mode and value and display the preset indicator ( P1 , P2 , P3 , or P4 ). In WEIGHT mode, the slicer beeps when the preset weight is on the platter. In SLICE mode, the slicer beeps when the preset number of slices has counted down to 0 .
– 7 – POWER UP When the slicer is plugged in, the control checks its own circuitry, goes through a series of illuminated displays, and ends with the scale at zero in weight mode. SCALE PLATFORM AND PLATTER ASSEMBLY Proper assembly of the nylon scale platform and stainless steel scale platter is necessary before weighing.
– 8 – WEIGHT MODE The scale is ready to weigh if the zero indicator is displayed when the platter is empty. Tare is permitted. Once invoked, the Tare value is set for all WEIGHT mode operations: Manual mode, Presets (P1 – P4), and Memory (M). The Tare value can be changed or turned off at any time.
– 9 – SLICING IN MANUAL MODE . . . without using the Presets (P1 – P4) or the Memory key In Weight Mode . . . Set the Tare, if needed. Set thickness. Slice product. The displayed weight will reflect the platter weight (less Tare, if NET was displayed).
– 10 – USING THE PRESETS: P1, P2, P3, P4 Press any Preset key — the last-saved values will be called up. For example, let's press the [ 1 ] Preset key and assume that the factory settings have not been changed. In Weight Mode . . . The preset weight, 0.
– 11 – USING THE MEMORY KEY: In Weight Mode . . . You can enter the preset weight by using the numeric keys (for example, 125). The lb indicator will blink and the preset weight, 1.25 lb, displays. [ If you make a mistake, press the Clear key, , and reenter the numeric value, or press the key twice to restore the previous values.
– 12 – SLICING — MODEL 2912 With the Gauge Plate fully closed, pull the Carriage all the way toward you until it reaches its stop. With the Meat Grip out of the way, place the product to be sliced on the Carriage Tray.
– 13 – CLEANING This machine must be thoroughly cleaned and sanitized after each day’s operation or after being idle for an extended period of time.
– 14 – Fig. 7 Fig. 8 Do not exceed chemical manufacturer's recommended concentrations for detergent or sanitizer. Do not exceed 200 parts per million concentration of available chlorine. For example, mixing 1 tablespoon of 5.25% sodium hypochlorite bleach with 1 gallon of water yields a solution containing 200 ppm of available chlorine.
– 15 – MAINTENANCE WARNING : UNPLUG SLICER POWER CORD AND TURN THE INDEX KNOB FULLY CLOCKWISE BEFORE PERFORMING ANY MAINTENANCE PROCEDURE. KNIFE SHARPENING The Hobart CleanCut TM stainless steel knife will provide long service in normal food retail or commercial kitchen use.
– 16 – FORM 35203 Rev A (Nov. 2004) PRINTED IN U.S.A. LUBRICATION — Carriage Slide Rod and Sharpener Lubricate the Carriage Slide Rod with Lubriplate FMO-200-AW oil (supplied). Either squirt 8 – 10 drops every 2 – 3 months (depending on usage) in the Wick Hole on the Carriage Transport (Fig.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Hobart 2812 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Hobart 2812 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Hobart 2812 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Hobart 2812 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Hobart 2812, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Hobart 2812.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Hobart 2812. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Hobart 2812 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.