Manuale d’uso / di manutenzione del prodotto CFX-IN-B del fabbricante Heat & Glo LifeStyle
Vai alla pagina of 23
1 - Do not store or use gasoline or other flam- mable vapors and liquids in the vicinity of this or any other appliance. - What to do if you smell gas • Do not try to light any appliance. • Do not touch any electrical switch. • Do not use any phone in your building.
2 These units MUST use one of the vent systems described in the Installing the Fireplace section of the Installers Guide . NO OTHER vent systems or components MA Y BE USED . This gas fireplace and vent assembly MUST be vented directly to the outside and MUST NEVER be attached to a chimney serving a separate solid fuel burning appliance.
3 TABLE OF CONTENTS Safety and Warning Information ............................................... 2 Service Parts Lists .................................................................... 4 Section 1: Approvals and Codes ............................
4 * Part number list on following page. * La liste des numéros de pièce se trouve à la page suivante. FB-GRAND SHOWN 2 1 3 * Part number list on following page.
5 (NG , LP) S ervice Parts List / Liste des pièces de rechange ITEM / PIÈCE Description PA RT NUMBER / N° DE PIÈCE ON/OFF Rocker Switc h / In terrupteur à bascule marche/arrêt 680-528 Burner Orifice NG (.
6 (NG , LP) S ervice Parts List / Liste des pièces de rechange ITEM / P IÈCE Description PA RT NUMBER / N° DE PIÈCE ON/O FF Rocker Switc h / In terrupteur à bascule marche/arrêt 680-528 Burner Orifice NG (.
7 * Part number list on following page. * La liste des numéros de pièce se trouve à la page suivante. 4 Log Set Assembly 2 1 3 5 6 7 8 9 10 11 12 FB-IN SHOWN 20 19 21 22 16 17 18 14 15 (NG , LP) Ex.
8 S ervice Parts List / Liste des pièces de rechange ITEM / PIÈCE DESCRIPTION PA RT NUMBER / N° DE PIÈCE ON/OFF Rocker Switc h / In terrupteur à bascule marche/arrêt 680-528 Burner Orifice NG (#.
9 (NG , LP) S ervice Parts List / Liste des pièces de rechange ITEM / PIÈCE DESCR IPTION PART NUMBER / N° DE PIÈCE ON/OFF Rocker Switch / Int err upteur à bascule marche/arrêt 680-528 Burner Ori.
10 Appliance Certification The Heat-N-Glo appliance models discussed in this Installers Guide have been tested to certification standards and listed by the applicable laboratories. Certification MODELS: FB-GRAND, FB-IN CFX-GRAND-B, CFX-IN-B LABOR ATORY: Underwriters Laboratories TYPE: Vented Gas Fireplace Heaters STANDARD: ANSI Z21.
11 ! ! ! ! ! ! Getting Started Introducing the Heat-N-Glo Gas Appliances Heat-N-Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside.
12 MI NIMUM FIREPLACE SI ZE Location CFX-GRAND-B and FB-GRAND CFX-IN-B and FB-IN Inches Millimeters Inches Millimeters A Fro nt W id th 35 889 30-1/4 768.4 B Rear Width 22-5/8 574.7 19 482.6 C Depth 14-1/8 358.8 14-1/8 358.8 * Heig ht 25-3/4 654 22-1/2 571.
13 MODEL DIMENSIONS Location CFX-GRAND-B and FB-GRAND CFX-IN-B and FB-IN Inches Millimeters Inches Millimeters A 22-1/2 571 18 457 B 8-3/4 222 6-1/2 165 C 33-3/4 857.2 29-3/8 746.1 D 30-9/16 776 26-1/16 661 E 23-7/8 606 20-5/8 524 F 18-7/16 468 15-3/16 385 G 25-3/8 644 22-1/8 562 H 24-1/2 622 21-1/4 540 Dimensions in brackets are millimeters.
14 Installing the Insert Step 1. Installing the Vent System Vent System Installation Precautions Before starting installation of vent kits, the installer should read these instructions and the Vent Kit Instructions to ensure that a proper vent installation is completed.
15 ! Slide the gas insert into place, and position any excess flexible vent pipe back up into the chimne y . Attach the pipe-to- cap adaptor to the termination cap and to the top of the flexible vent pipe and set the cap in place at the top of the chimne y.
16 Figure 4. This option shows both exhaust and inlet air vent pipes attached to the adaptor. W ARNING: THE EXHAUST VENT PIPE MUST ONL Y BE CONNECTED T O THE EXHAUST ST ARTING COLLAR OF THE UNIT AND THE CENTER COLL AR OF THE TERMINA TION CAP .
17 Figure 5. Typical configuration of vent liners. Note: Inspect for exhaust collar gasket to insure positive exhaust seal. TERMINATION CAP ADAPTOR STAINLESS STEEL ADAPTER FOR EXHAUST (MUST BE INSTALL.
18 Step 2. Positioning, Leveling, and Securing the Insert • Place the insert into position. • Level the insert from side to side and from front to back. Use the leveling legs included with the manual bag if necessary to set each corner of the base.
19 Step 5. Gas Pressure Requirements Pressure requirements for these gas appliances are shown in the table belo w. Pressure Natural Gas Propane Minimum 5.0 inches 11.0 inches Inlet Pressure w .c. w .c. Maximum Inlet 14.0 inches 14.0 inches Gas Pressure w .
20 ! Optional Accessories Installation of the electrical junction box is required if using a blower or remote. To install: • Uncoil the junction box cord and feed the end of the cord through the hole on the right side of the base pan. • Turn the junction box at a 45-degree angle and insert it into the sidewall of the base pan.
21 Step 7. Installing Logs and Ember Material Positioning the Logs The logs have been packaged separatel y . Refer to the installation instructions that accompany this manual. Save the log instructions with this manual. If sooting occurs, the logs might need to be repositioned slightly to avoid excessive flame impingement.
22 Step 9. Before Lighting the Appliance Before lighting the appliance, be sure to do the following: Remove all paperwork from underneath the fireplace. Review safety warnings and cautions • Read the Safety and Warning Information section at the beginning of this Installers Guide .
23 Maintaining and Servicing Your Appliance Appliance Maintenance Although the frequency of servicing and maintenance will depend on use and the type of installation, you should have a qualified service technician perform an appliance check- up at the beginning of each heating season.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Heat & Glo LifeStyle CFX-IN-B è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Heat & Glo LifeStyle CFX-IN-B - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Heat & Glo LifeStyle CFX-IN-B imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Heat & Glo LifeStyle CFX-IN-B ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Heat & Glo LifeStyle CFX-IN-B, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Heat & Glo LifeStyle CFX-IN-B.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Heat & Glo LifeStyle CFX-IN-B. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Heat & Glo LifeStyle CFX-IN-B insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
