Manuale d’uso / di manutenzione del prodotto 237-410 del fabbricante Graco Inc.
Vai alla pagina of 17
.
3X8–448 Rev . F Supersedes Rev . C Includes Rev . D and E changes Parts Change Notice Some parts in Rev . C of manual 308–448 have changed but have not yet been changed in the instruction manual. Please note the changes below and mark them in your manual or keep this sheet with your manual.
Table of Contents Symbols Warnings ...................................... 2 Setup.. ....................................... 4 System Component Information .................. 6 Operation ..................................... 8 Flushing ................
EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result in serious injury. 0 0 l 0 0 0 0 0 0 0 This equipment is for professional use only. Read all instruction manuals, tags, and labels before operating the equipment.
A CAUTION This equipment is compatible with most water based materials. See the wetted parts in the Tech- nical Data section and your fluid and solvent manufacturer’s compatibility information. Do not use catalyzed materials in heated applica- tions.
III. Unpacking the System In addition to the assembled unit, these components are packed loosely or separately: suction assembly, hose set, gun, instruction manuals. These are the manuals you should receive: 308-I 94 Husky 307 pump 307-452 Air spray gun 308-325 Fluid regulator 307-805 Fluid heater 307-273 Fluid filter IV.
System Component Information VI. Using the G700N Air Spray Gun 1. 2. 3. 4. 5. 6. 7. Refer to Fig. 3. Make initial fluid and air adjustments at the pump for maximum efficiency. If you make adjustments at the gun, take noted of what you do. Then, if the results are not satisfac- tory, you can easily return the gun to its previous adjustment.
System Component Information VIII. Using the Air Regulators and Needle 1. 2. 3. 4. 5. valve See Fig. 5. Always open air and fluid regulators slowly to pre- vent surging during startup. The air regulator (6a) on the right side of the pump controls air to the pump, and the regulator (6b) on the left side controls air to the gun.
Operation I. Pressure Relief Procedure The system remains pressurized until pressure is manually relieved. To reduce the risk of serious injury from pressurized fluid, accidental spray from the gun, o.
Operation 12. Adjust the needle valve to set the pump cycle rate at 1 stroke every 15 seconds. 13. Turn the heater dial to 3. Whenever the heater set- ting is changed, allow the fluid to circulate and sta- bilize before checking the temperature (about IO minutes) .
Operation v. Production Spraying You are now ready for production spraying. If you stop spraying for more than 30 minutes, turn off the heater to prevent overheating the fluid. VI. Shutting Down the System Shut down the system at the end of the work shift and before checking, adjusting, cleaning, or repairing the system.
Flushina +a 14. 15. KEY A Bleed-type master air valve C Air line 3 Fluid heater 6a Pump air regulator 6b Gun air regulator 9 3-way valve 13 Drain hose 44 Fluid regulator 45 Fluid filter 48 Filter drain valve For a first-time flush, trigger the gun, and circulate the solvent for 20 seconds.
Parts Model 237410, Series A Ref Part No. No. 1 235-230 2 217-752 3 220-522 4 110-160 5 108-233 6 111-804 7 11 O-209 8 108-l 90 9 214-711 10 214-699 11 205-l 69 12 206-966 13 206-965 14 188-l 73 15 16.
Parts 16’ Model 237410, Series A 25 60 / 23 308-448 13.
Notes . 14 308-448.
Notes c 308-448 15.
Technical Data Manual Change Summary The current revision of this manual includes the following changes: Page 12, Parts List: l The quantity of item 25 (elbow) is changed to 3. l The quantity of item 47 (elbow) is changed to 1. Page 13, Parts Drawing: l Item 60 is changed to 62, and item 62 is changed to 60.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Graco Inc. 237-410 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Graco Inc. 237-410 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Graco Inc. 237-410 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Graco Inc. 237-410 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Graco Inc. 237-410, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Graco Inc. 237-410.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Graco Inc. 237-410. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Graco Inc. 237-410 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
