Manuale d’uso / di manutenzione del prodotto H8000-07 del fabbricante Genie
Vai alla pagina of 16
For 7’ 6” Doors. Extension Kit is available for 8’ Doors Included Wall Console MUST be installed prior to Operation of this Garage Door Opener. Safe-T-Beam ® S afety R e ve rs e Sy stem MUST be Installed and the F orce Co ntro ls M UST be Pro pe rly set to cl os e doo r.
2 For Help, call 1-800-35-GENIE or visit www.geniecompany.com * Model Number and Serial Number are located on Motor Cover inside the lens. See Power Head Assembly Exploded View on page 15 IT IS CRITICAL THAT ALL SAFETY WARNINGS MARKED CLEARLY IN BOTH THE MANUAL AND POSTER ARE READ, UNDERSTOOD AND FOLLOWED.
For Help, call 1-800-35-GENIE or visit www.geniecompany.com 3 oVeRView of poteNtial haZaRDS Overhead doors are large, heavy objects that move with the help of springs under high tension and electric motors.
4 For Help, call 1-800-35-GENIE or visit www.geniecompany.com Figure 1 Note Door Type SECTIONAL DOOR, TO RSION SPRINGS SECTIONAL DOOR, EXTENSION SPRINGS ONE-PIECE DOOR, TRACKLESS m e a S u R e G a R a G e D o o R h e i G h t A Measure door height (floor to top of door) using a tape measure.
Door Center Line Figure 5 Check Power Head location 11’ Grounded outlet 10’ (7’-6” door) (8’ door) 5 For Help, call 1-800-35-GENIE or visit www.geniecompany.com C Check wall for a stud or a solid header at your mark: (If checking a finished wall, a stud finder may be helpful).
6 For Help, call 1-800-35-GENIE or visit www.geniecompany.com Figure 8 Recommended Tools Go to Assembly and Installation Poster for full Installation Instructions.
7 For Help, call 1-800-35-GENIE or visit www.geniecompany.com a D j u S t i N G l i m i t S w i t C h e S a N D f o R C e C o N t R o l S Adjustment 1: A Pre-set Force Controls to midpoint between Hi and LO ( Figure A-1 ). B Adjust the Close Limit Switch: ( Figure A-2 ).
8 For Help, call 1-800-35-GENIE or visit www.geniecompany.com NOTE The door must contact the 2” x 4” board before the Carriage activates the Close Limit Switch.
9 For Help, call 1-800-35-GENIE or visit www.geniecompany.com Learn Code Button Figure MA-2 Learn Code Button and Indicator Light A Install two 60 Watt light bulbs (not included) into Light Sockets ( Figure MA-4 ): • Rough service, 130 Volt bulbs are recommended.
10 For Help, call 1-800-35-GENIE or visit www.geniecompany.com A Monthly: • Door springs and door hardware: – Oil door roller, bearings, and hinges using silicone lubricant or light oil. • Balance Door. – Close door. – Release Magnetic Carriage Assembly f r om Rail Assembly b y pulling down o n Emergency Release Knob.
11 For Help, call 1-800-35-GENIE or visit www.geniecompany.com Opener System Self-Diagnostic Troubleshooting • SeeStatus Light onFigure MA-2,page 9) You See Problem What to D.
12 For Help, call 1-800-35-GENIE or visit www.geniecompany.com General Troubleshooting (Always Check the Status LED Light) Problem What To Do Opener does not run 1 . Check power source. from Remote Control A. If Opener is connected to an outlet : • Plug a working lamp into outlet used for Power Head.
13 For Help, call 1-800-35-GENIE or visit www.geniecompany.com General Troubleshooting (Always Check the Status LED Light)(Continued) Problem What To Do Remote Control has less • Relocate Remote Control inside car. than 25’ operating range • Ensure Remote Control is pointing toward garage door when pressing Control Button.
14 For Help, call 1-800-35-GENIE or visit www.geniecompany.com Item Part Name Qu a n ti t y Item Part Name Required 1 Power Head Assembly (main carton) 1 2 1/4”-20 x 13/16” Hex Head Shoulder Bolt .
15 For Help, call 1-800-35-GENIE or visit www.geniecompany.com h a R D w a R e e x p l o D e D V i e w NOTE Opener will not function unless Safe-T-Beam® System is installed and Force Controls are properly set.
16 For Help, call 1-800-35-GENIE or visit www.geniecompany.com ® No C.O.D. shipments. Please include check or money order, made payable to The Genie Company. Do not send cash. Allow 3-4 weeks for delivery. 1-800-354-3643. Please have part number and credit card ready.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Genie H8000-07 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Genie H8000-07 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Genie H8000-07 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Genie H8000-07 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Genie H8000-07, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Genie H8000-07.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Genie H8000-07. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Genie H8000-07 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
