Manuale d’uso / di manutenzione del prodotto 1022 del fabbricante Genie
Vai alla pagina of 28
SA VE THIS MANUAL FOR FUTURE REFERENCE For Answers and Assist ance: 1.800.354.3643 or visit www .geniecompany .com Model 1022/1024 Includes Remote Control (Up to 7 Single Button Programmable Controls Available) Homelink ® and Car2U™ compatible Homelink ® is a registered trademark of Johnson Controls T echnology Company .
PN# 3642036212, 8/09/2007 2 Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension, and electric m.
PN# 3642036212, 8/09/2007 3 T ABLE OF CONTENTS OPERA T OR FEA TURES INTELLICODE ® Rolling Code Security System. An electronic rolling code system that enhances the security of the door operator by continuously changing the access code each time the remote control is used.
PN# 3642036212, 8/09/2007 6 T o avoid damage to your door and/or operator , make sure you disable and/or remove any door locks, ropes, and/or cables prior to inst alling your operator . ( Refer to Section 1.) 4 PRE-INST ALLA TION CHECK LIST FOR HELP-1.
PN# 3642036212, 8/09/2007 5 TYPICAL SECTIONAL DOOR INST ALLA TION FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM TYPICAL SUPPORT BRACKET EXTENSION SPRING OR TORSION SPRING SAFETY BEAMS BRACES ADDED HEADER BRACKET MOUNTING BOARD POWER CORD (APPROX.
PN# 3642036212, 8/09/2007 6 RECOMMENDED TOOLS FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 3/16" Drill Bit 1/4", 7/16", 3/8" and 1/2" Sockets S tep ladder Drill Ratchet Carpenter ’ s level Pencil T ape measure Wire strippers Phillips screwdrivers Adjustable wrench P AR TS IDENTIFICA TION - Not Shown Full Size .
PN# 3642036212, 8/09/2007 F ASTENERS - Shown Full size ( See Parts List below for full description.) Lag screw - 5/16" x 2" Self-drilling Screw 1/4"-20 x 3/4" Hex Flange Nut - 1/4&.
PN# 3642036212, 8/09/2007 8 1-PIECE RAIL HARDW ARE ASSEMBLED VIEW FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 3-PIECE RAIL HARDW ARE ASSEMBLED VIEW Chain tensioner Rail with chain Chain T rolley Slide Release Knob Header Bracket Po wer Head Po wer Cord Clevis Pin, Long & Cotter Pin N O T E Som e d o ors need bra cin g.
PN# 3642036212, 8/09/2007 9 OPERA T OR ASSEMBL Y FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 1 NOTE: Three (3) piece rail assemblies are for a 7 foot high door . Clear a workspace area to unp ack and organize box and contents for assembly . 1. There are 4 boxes inside the carton.
10 POWER HEAD & RAIL ASSEMBL Y FIG . 1-5 Chain adjustment . FIG . 1-4 Rail - Power head assembly . NOTE: Handle carefully! Drive chain can slide out of rail. NOTE: For power head and rail assembly locate Bag 1 from Box 1. 1. Attach rail assembly to power head by aligning the sprocket onto the motor shaf t.
PN# 3642036212, 8/09/2007 11 FIG . 2-2 Finding highest point of travel . INST ALLA TION FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 2 HEADER AND DOOR MOUNTING BRACKETS: 1. Finding header bracket mounting location . • Close garage door . – Use a pencil and level.
12 MOUNTING THE OPERA T OR: 1. Getting started . • Position assembled rail on wall next to header bracket. (Fig. 2-4) . – Place material on floor under power head to protect from scratching. (A box, stool, or similar device may be needed to clear a torsion spring.
PN# 3642036212, 8/09/2007 13 DOOR BRACKET : NOTE: For door bracket and bolts locate Bag 4 from Box 2. 1. Finding door bracket mounting location . • Door bracket is mounted as high on door as possible along vertical centerline and NO LOWER THAN top set of rollers (Fig.
14 NOTE: For Wall Control, wire and insulated staples locate Bags 6 and 7 from Box 2. 1. Wall Control location. • Wall Control location should be in direct sight of door . • It should be at least five feet (5') above floor to prevent small children from operating door .
PN# 3642036212, 8/09/2007 15 3.Securely fasten wires. • Securely fasten wires to ceiling and wall using insulated staples provided. – Use insulated staples. – S taples should be snug only . • If rear cover is attached to power head, remove it.
PN# 3642036212, 8/09/2007 16 SAFETY BEAM SYSTEM INST ALLA TION FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 4 NOTE: The operator will not close the door automatically unless the Safety Beam System is installed. NOTE: For Sensors, screws, wire, and insulated staples locate items and Bag 8 from Box 3.
PN# 3642036212, 8/09/2007 17 3b. Wiring (pre-wired) . • Route wire from wall to Safety Beam sensors. (Fig. 4-5b) . • S plice pre-wiring to shortened sensor wire, match wire pairs dash-to-dash and plain-to-plain . - T rim sensor wire to approximately one foot (1 ft) from sensor .
PN# 3642036212, 8/09/2007 18 CONNECTING TO POWER FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 5 Plug the operator into a properly grounded electrical outlet. (Fig. 5-1) • T o reduce the risk of electrical shock, this equipment has a grounded type plug that includes a third ( grounding ) pin.
PN# 3642036212, 8/09/2007 19 DOOR LIMITS FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 6 The OPEN (UP) and CLOSE (DOWN) door positions are controlled by making the adjustments on the panel located on the bottom of the power head.
PN# 3642036212, 8/09/2007 FIG . 6-5 2 x 4 under center of door opening. CONT ACT REVERSE TEST The force adjustment s and limit switch settings MUST BE COMPLETED before testing. 1. T esting . • Open garage door using wall control. – Place a 2" x 4" board (laid flat) under center of garage door opening (Fig.
PN# 3642036212, 8/09/2007 21 FCC and IC CER TIFIED FIG . 7-1 Learn code button and LED SET SET OPEN FORCE CL OSE C ODE LEARN LIMIT MANU AL Open T ravel Limit Open Set Limit Button Close T ravel Limit .
PN# 3642036212, 8/09/2007 22 REMOTE CONTROL BA TTERY REPLACEMENT AND VISOR CLIP INST ALLA TION 8 FIG . 8-1 Open battery cover . 1. Battery replacement . • Use coin, ball-point pen or similar device. – Gently push straight in on battery cover lock tab as shown (Fig.
PN# 3642036212, 8/09/2007 Use wall control supplied with operator . Any other wall control can cause the operator to operate unexpectedly . CAUTION If you have any questions, please do not hesitate to cont act customer service at: 1.800.354.3643 23 IMPORT ANT SAFETY INSTRUCTIONS 1.
PN# 3642036212, 8/09/2007 24 CIRCUIT WIRING DIAGRAM FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM 1 2 3 4 5 6 1 2 3 4 12 3 1 2 POWER CORD CORDON DE SECTEUR CABLE ELÉCTRICO TERMINAL BLOCK BORNE B.
PN# 3642036212, 8/09/2007 TROUBLESHOOTING GUIDE - OPERA TION FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM PROBLEM WHA T TO DO Operator does NOT run from wall control. • Check power source. – Plug a lamp into outlet used for power head. If lamp works, power source is OK .
PN# 3642036212, 8/09/2007 26 TROUBLESHOOTING GUIDE - POWER HEAD LED FOR HELP-1.800.354.3643 OR WWW .GENIECOMP ANY .COM Power head LED Possible Problem Solution Red LED showing Green LED showing OFF OF.
PN# 3642036212, 8/09/2007 T ransmitters comply with all United S tates and Canadian legal requirements as of the date of manufacture. No warranty is made that they comply with all legal requirements of any other jurisdiction.
PN# 3642036212, 8/09/2007 28 The Genie Comp any Professional Access Systems LIMITED W ARRANTY What is covered: Any defect in material and product workmanship from personal, normal household use in accordance with the Owner ’ s Manual. For how long: Limited 1 year warranty on parts, 5 years on motor .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Genie 1022 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Genie 1022 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Genie 1022 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Genie 1022 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Genie 1022, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Genie 1022.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Genie 1022. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Genie 1022 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
