Manuale d’uso / di manutenzione del prodotto MVP del fabbricante Allstar
Vai alla pagina of 20
INSTALLATION AN D OWNER’S MANUAL As of date of manufacture, meets all ANSI/UL 325 Safety Requirements for V e h i c u l a r Ga rage Doo r Ope ners READ T HIS M ANUAL CAREFUL LY BEFO RE INSTAL LATION O R US E 107063 INSTALLER: Place this manual in the plastic envelope provided and permanently attach to t he wall near the pushbutton.
The purpose of this booklet is to p rovide assembly, installation and operation informatio n c oncerning the herein described Residential Garage Door Op ener and rela ted A cc ess ory Pr oduc ts. NOTICE IT IS IMPORTANT THAT THIS INSTRUCTION MANUAL BE READ AN D UNDERSTOOD COMPLETELY BEFORE INSTALLATION OR OPERATION IS ATTEMP TED.
NOTE: The Tee Rail/Chain Assembly is packaged s eparatel y from the Power Unit. Th e Inn er T roll ey h alf , Front Idler Sprocket, Chain, and Limit Cams are assembled on the Tee Rail at the factor y. Follow the steps outlined below to complete assembly prior to installation.
WARNING SPRINGS, PULLEYS, CABLES AND MOUNTING HARDWARE USED TO BALANCE YOUR GARAGE DOOR ARE UNDER EXTREME TENSION AT A LL TIME S AND CAN CAUSE SEVERE INJURY OR DEATH IF DISTURBED.
W ARNING! T O REDUCE THE RISK OF SEVERE INJUR Y OR DEA TH READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS! AN UNBAL ANCED DOOR OR ONE TH AT STICKS OR BINDS M A Y PREVENT THE SENSING SYSTEM FROM WORKING PROPERLY, CAUSING INJURY OR DE AT H. ENSURE DOOR IS PROPERLY BALANCED AND ELIMINATE ANY STICKING OR BINDING PRIOR TO INSTALLATION OF OPENER.
FRO NT MO UN TING BRAC KET MUS T BE I NS TALL ED TO A STRUCTURAL SUPPORT (STUD) ON THE HE ADER WALL. FAILURE TO DO SO COULD CAUSE SENSING SYSTEM TO MALFUNCTION, RESULTING IN ENT RAPMENT, INJURY OR DEATH. REINFORC E HEADER IF NECESSARY USING A 2 x 6 AND LAG SCREWS (NOT PROVIDED).
STEP 4: Mou nt Po wer Head to Ceiling: Since there is such variety in ceiling structures, all th e mounting possibilities for the Power Unit can not be illustrated here. The main c oncern is mounting the Power Unit securely to the ceiling joists for operational stren gth, rigidity and safety.
FIBERGLASS, ALUMINUM OR LIGHTWEIGHT STEEL GARA GE DOORS WILL RE QUIRE REINFORCEMENT BEFORE INSTALLATION OF DOOR MOUNTING BRACKET. CONTACT YOUR DOOR MANUFACTURER FOR A REINFORCEMENT KIT OR INSTRUCTIONS.
STEP 9 : Consult the label on the rear panel of the Open er to d et ermi ne i ts pr op er w ork in g volt a ge. Normally it will be mark ed for 115V, 60 c y c le operation. (If it is an export model designed for 220V, 50 cycle operation, the label will clearly indicat e this.
IN STA LLA TION OF A STAN DA RD WA LL PUSH BUTTON If desired, a standar d wall push button may be installe d and connected to your operator. A standard wall push button is not included in your hardware package, it can be purchased from your pr ofessional installing dealer or a door bell button [ without light] can be subs tituted.
STEP 4: Run the wire from the Super Station to the opener, supporting it at 18” int ervals with suitable staples. Leave a sufficient length to make the necessary conn ecti ons to th e op ener t ermina l st rip. WARNING: SOME LOCAL BUILDING CODES DO NOT ALLOW SURFACE WIRING.
Programmi ng the MVP Radio Recei v er in the Po wer Head U nit Your opener will “learn” up to eight code transmissions from preprogrammed transmitters. Locate the “Learn Enable” Button on the Super Station (Deluxe Wall Pushbutton Station). The button is located insid e a small hole on the front of the super station.
INST A L LATION OF 2 WIRE SAFE FINISH PHOT OSYST EM STEP 1: Mark t he position of the SAFE FINISH™ Photosy stem as follows: Mark a line on the left and right door jamb (close to the door track) FOUR (4 ) inches AND SIX (6) inc hes ab ove th e floor.
F. Using two (2) wire nuts (suppli ed), connect the wire ends at the SAFE F INISH™ Photosystem receiver to the pigtail wire ends coming ou t of the receiver unit. Although not required, it is recommended to connect the trace wire ends together and the unmarked wi re ends together.
• NEVER LET CHILDREN OPERATE OR PLAY WITH DOOR CONTROLS. KEEP THE REMOTE CONTR OL A WAY FROM CHILDREN. • ALWAYS KEEP A MOVING DOOR IN SIGHT AND KEEP PEOPLE AND OBJECTS AWAY FROM THE DOOR AR EA UNTIL THE DOOR IS COMPLETELY CLOSED. NO ONE SHOULD CROSS THE PA TH OF A M OVING DOOR.
STEP 1: Testing the Limit Settings: To che ck the Limit Settings, start the Opener by pushing th e standard wall Push Button or Super Station. Be prepared to activate the button again quickl y - per the Operating Parameters outlined ab ove - or if you see that the d oor is going to over travel.
Down force adjustments are correct, the door will reverse within two seconds o f contacting the object and travel to the Full Open position. If this does not occur, recheck the Limit Adjustments (Step 1, previous) and Sensitivity Adjustments (Step 2 & 3, previous .
Wiring D iagram 110796 2. Close Pushbutton — Gr een -ba ckl ight ing, arr ow pointing down. Used to start th e door downward. This button has no effect on a door in motion. Will allow constant pressure close opera tion if the photocell is misaligned.
Your Res idential Garage Doo r Ope ner is furn ished with an enhanc ed 2 Wir e Safe Fini sh™ P hotos ystem. T he feat ures includ e: Time-Saving Electrica l Connections.
1 2 3 4 5 6 7 8 9 Plus Button Zero Bu tton Minus Button IF DES IRED, RECORD YOUR RAD IO TRA NSMIT TER C ODE P OS ITION SETTINGS HERE See Page 11 for Radio System programming instructions and FCC/RSS-210 Industry Canada state ment. T he open er rad io sy stem is HomeLink® compatible.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Allstar MVP è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Allstar MVP - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Allstar MVP imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Allstar MVP ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Allstar MVP, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Allstar MVP.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Allstar MVP. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Allstar MVP insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
