Manuale d’uso / di manutenzione del prodotto PS7300HS-45 del fabbricante Dolmar
Vai alla pagina of 32
1 Instruction Manual Original Instruction Manual Important: Read this instruction manual carefully before putting the chain saw into operation and strictly observe the safety regulations! Keep this instruction manual! http://www .
2 T able of contents Page Packing ................................................................................ 2 Delivery inventory .............................................................. 3 Symbols ..........................................
3 STOP 1 4 5 6 7 3 2 8 Delivery inventory 1. Chain saw 2. Guide bar 3. Saw chain 4. Chain protection cover 5. Universal wrench 6. Offset screwdriver 7.
4 4 5 6 7 1 2 3 1 SAFETY PRECAUTIONS Intended use Power chain saws This power chain saw may be used only for sawing wood out of doors. It is intended for the followung uses depending on its class: - Professional and mid-class: Use on small, medium and large trees: felling, limb removal, cutting to length, thinning.
5 6 5 7 9 8 Fuels / Refuelling - Stop the engine before refuelling the chain saw. - Do not smoke or work near open Þ res (5). - Let the engine cool down before refuelling. - Fuels can contain substances similar to solvents. Eyes and skin should not come in contact with mineral oil products.
6 Kickback - When working with the chain saw dangerous kickbacks may occur . - Kickback occurs when the upper part of the end of the guide bar inadvertently touches wood or other hard objects (10). - This causes the saw to be thrown back toward the user with great force and out of control.
7 - Be careful when cutting splintery wood. Cut pieces of wood may be pulled along (risk of injuries). - When cutting with the upper edge of the guide bar, the chain saw may be pushed in the direction of the user if the chain gets clamped. For this reason use the lower edge of the bar whenever possible.
8 SERVICE T ransport and storage - When changing your location during work switch off the chain saw and actuate the chain brake in order to prevent an inadvert- ent start of the chain.
9 Denomination of components 1 Handle 2 Filter hood 3 Filter hood clip 4 Tubular handle 5 Hand guard (release for chain brake) 6 Muf ß er 7 Spike bar 8 Chain tensioning screw 9 Retaining nuts 10 Chai.
10 5 7 6 4 5 1 2 3 Lift the chain ( 6 ) over the sprocket ( 5 ). Using your right hand, guide the chain into the top guide groove on the guide bar ( 7 ). CAUTION: Note that the cutting edges along the top of the chain must point in the direction of the arrow! Position the guide bar ( 4 ) and push against the sprocket ( 5 ) as shown by the arrow .
11 2 13 3 11 12 6 8 9 10 Guide the chain over the chain catch ( 9 ). Pull the guide bar as shown by the arrow to take the slack out of the chain, so that it comes up to the bottom edge of the guide bar ( 10 ). Pull the chain ( 6 ) around the sprocket nose ( 8 ) of the guide bar in the direction of the arrow .
12 ST OP 2 13 1 2 1 Checking the chain tension The tension of the chain is correct if the chain rests against the bottom side of the guide bar and can still be easily turned by hand.
13 Chain oil Use an oil with adhesive additive for lubricating the chain and guide bar . The adhesive additive prevents the oil from being ß ung off the chain too quickly . We recommend the use of chain oil which is bio-degradable in order to protect the environment.
14 Refuelling FOLLOW THE SAFETY PRECAUTIONS! Be careful and cautious when handling fuels. The engine must be switched off! Thoroughly clean the area around the caps, to prevent dirt from getting into the fuel or oil tank. Unscrew the cap and Þ ll the tank with fuel (fuel/oil mixture) or chain oil as the case may be.
15 1 2 3 Checking the chain lubrication Never work with the chain saw withoute suf Þ cient chain lubri - ca tion. Otherwise the service life of the chain and guide bar will be reduced. Before starting work check the oil level in the tank and the oil feed.
16 Starting the engine Start the chain saw only after having assembled it com- pletely and inspected. Move at least 3m away from the place where you fuelled the saw . Make sure you have a good footing, and place the saw on the ground in such a way that the chain is not touching anything.
17 D Adjusting the carburetor CAUTION: Carburetor adjustment may only be done by a specialist DOLMAR service centre! Only adjusting screw (S) can be manipulated by the user .
18 E Working in winter In order to prevent carburetor icing in conditions of low tempe- rature combined with high humidity , and below + 5°C in order to get up to operating temperature faster , heated air can be taken from the cylinder .
19 The sharpening angle of 25° must be identical for all cutters! Different angles result in a roughly , irregularly running chain, increase wear and tear and cause chain beakage. The front rake 60° of the cutter results from the cut depth of the round Þ le.
20 1 2 Files and how to work with them Sharpen using a special Þ le holder with a saw chain round Þ le. Normal round Þ les are not appropriate for this work. See „Accessories“ for the order number . File the Þ rst cutter half with a 5.5 mm dia.
21 8 10 11 7 5 4 5 1 6 7 2 3 Cleaning the brake band and sprocket interior CAUTION: Before doing any work on the guide bar or chain, always switch off the engine and pull the plug cap off the spark plug (see „Replacing the spark plug“) .
22 12 16 15 13 17 Replacing the saw chain CAUTION: Use only chains and guide bars designed for this saw (see the Extract from the spare-parts list) ! Check the sprocket before mounting a new chain. Worn out sprockets ( 12 ) may damage the new chain and must therefore be replaced.
23 3 5 4 CAUTION: T o prevent eye injury , always wear eye protection when cleaning the Þ lter with compressed air! Do not use fuel to clean the air Þ lter . Unhook the Þ lter hood clips ( 1 ) with the combination tool and remove the Þ lter hood ( 2 ).
24 10 Replacing the spark plug CAUTION: Do not touch the spark plug or plug cap if the engine is running (high voltage). Switch off the engine before starting any maintenance work.
25 11 Replacing the starter cable / Replacing the return spring Unscrew three screws ( 1 ). Remove fan housing ( 2 ). NOTE: The screws ( 1 ) are secured against falling out of the housing. CAREFUL! Injury hazard! Do not unscrew screw (5) if the return spring is under tension.
26 13 15 16 14 Cleaning the cylinder area Remove the Þ lter hood and air Þ lter . Remove the spark plug cap and unscrew the spark plug. Press in the starting valve and activate the chain brake. Push the cable cutout and ignition cable out sideways. Unscrew the two rearmost screws on the cover .
27 Instructions for periodic maintenance T o ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be pe r- formed regularly . Guarantee claims can be recognized only if this work is performed regularly and properly .
28 Spare parts Reliable long-term operation, as well as the safety of your chain saw , depend among other things on the quality of the spare pa rts used. Use only original DOLMAR parts, marked Only original spare parts and accessories guarantee the highest quality in material, dimensions, function and safety .
29 15 10 11 9 16 4 8 7 6 5 13 20 21 22 23 24 27 25 1 2 3 12 14 10 11 17 28 Extract from the spare parts list Use only original DOLMAR parts. For repairs and replacement of other parts, see your DOLMAR service centre.
30 EU Conformity Declaration The undersigned, T amiro Kishima and Rainer Bergfeld, as authorized by DOLMAR GmbH, declare that the DOLMAR machines, T yp: 038, 039, 040 Chain saw EU prototype test certi Þ cate No. PS-6400 (040) 481 1004.1 1012 PS-7300 (039) 481 1004.
31.
32 Form: 995 701 221 (2012-06 GB) 106 Speci Þ cations subject to change without notice DOLMAR GmbH Postfach 70 04 20 D-22004 Hamburg Germany http://www .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Dolmar PS7300HS-45 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Dolmar PS7300HS-45 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Dolmar PS7300HS-45 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Dolmar PS7300HS-45 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Dolmar PS7300HS-45, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Dolmar PS7300HS-45.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Dolmar PS7300HS-45. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Dolmar PS7300HS-45 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
