Manuale d’uso / di manutenzione del prodotto HCG450 del fabbricante CDA
Vai alla pagina of 15
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshir e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.
Dear Customer , Thank you for choosing our product. This appliance is easy to use; read this handbook carefully before installing and using it, however . Y ou will find the correct indications for the best installation, use and maintenance of the product.
General warnings 002 LINGUE 28-09-2005 19:29 Pagina 23 I E GB • If a gas appliance is used for a long time it may require extra ventila- tion (opening a window or increase of the forced exhaust). • Be careful not to place saucepans with unstable or deformed bottoms on the burner to avoid accidents by overturning or spil ling over of liquid.
Description of the main parts of the appliance Instructions for use 1 = grid 2 = cover 3 = spreader 4 = ON spark plug 5 = safety valve (for models equipped with a safety valve) 6 = knob for burner ign.
Instructions for use The hob control area houses the devices and knobs for operation of the gas burners. 002 LINGUE 28-09-2005 19:29 Pagina 25 In order to ignite a burner , it is necessary to depress the knob while rotating it anti- clockwise, till the index is aligned with the position corresponding to the maximum gas delivery (i.
Instructions for use Container table (use flat-bottomed saucepans) Auxiliary (Ø = 55) Medium quick (Ø = 75) Quick (Ø = 100) Burners (heights cover) mm Ø min.
Maintenance and c leaning Do not use jet of steam for cleaning. Instructions for use 002 LINGUE 28-09-2005 19:29 Pagina 28 Before any operation disconnect the appliance electrically . W ash the enamelled parts with lukewarm water and detergent. Do not use abrasive products.
Below we give the instructions for qualified installers so that the installation, setting and maintenance operations are performed correctly and according to the regulations in force. Positioning This appliance isn’t connected to any scavenging devices of combustion products.
T o perform these operations the qualified installer will follow the indications given in the "Adaptation to the various types of gas" section. For safety operation make sure that the supply pressure respects the values given in the "T able of burner and injector characteristics”.
Instructions for installation ELECTRICAL CONNECTION The appliances are provided with a three-pole feeding cable and work with alternate current and single-phase voltage indicated on the “rating plate of the product “report at the end of the instruction manual and on the product.
Adaptation to different types of gas T o adapt the appliance to a gas different from that for which it was set up (see label on both the packaging and the bottom of the appliance) proceed as follows: • remove the grids • remove the covers and the spreaders • with a 7 mm socket spanner unscrew and remove the injectors.
Instructions for installation 002 LINGUE 28-09-2005 19:29 Pagina 33 I E GB Setting the minima The flame on the small output is regulated in the factory . When the injec- tors have been replaced or there are special mains pressure conditions, it may be necessary to regulate the minimum again.
Burner and nozzle characteristic table Instructions for installation Quick (Ø = 100) Medium quick (Ø = 75) Auxiliary (Ø = 55) Rated supply pressure (mbar) (1 mbar ≅ 10,197mm H 2 O) (*) = With dry.
Instructions for building in the units The appliance is of class 3. It can be installed with just one side part (to right or left of the hob) higher than the cooking hob and placed at a minimum distance as shown in figure.
Instructions for installation 002 LINGUE 28-09-2005 19:29 Pagina 36 mm I E GB • Position the special sealed gasket (provided) on the edge of the hob making sure that the ends meet without one lying on top of the other . • Put the hob in the unit opening making sure that it is centred.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il CDA HCG450 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del CDA HCG450 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso CDA HCG450 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul CDA HCG450 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il CDA HCG450, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del CDA HCG450.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il CDA HCG450. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo CDA HCG450 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
