IT
Manuale d'uso ufficiale

Max Desktop (Ultimate VII)

31 pagine·502 KB·Computer·PDF·ENNLJA
Max Desktop (Ultimate VII)
Indice dei contenuti 2 sezioni ENG · USER’S GUIDE DESKTOP NAIL DUST COLLECTOR MAX ULTIMATE VII MostraNascondi
Page 1 of the Max Desktop (Ultimate VII) user manual — ENG
Pagina 1 · clicca per ingrandire
Pagina 1

ENG

USER’S GUIDE DESKTOP NAIL DUST COLLECTOR MAX ULTIMATE VII

General description The MAX Ultimate VII nail dust collector is designed for use by professional manicurists. It is used for removal of dust, which appears in the process of nail filing and removal of artificial coatings.

  • Usage of the nail dust collector is recommended:
  • during gel and acrylic nail extension, nail correction;
  • while removing of gel polish and other artificial coatings;
  • when performing manicure (especially hardware one).

Complete set 1. Dust collector with a filter bag installed. 2. Additional filter bag. 3. Passport.

Operational principles The manicurist works in the dust collector fan grill area. The dust-air mixture is sucked with the fan impeller of the dust collector. Clean air flows back into the room after its filtration through the bag filter. Dust is collected inside the filter. The manicurist cleans the filter bag after finishing.

Max Desktop (Ultimate VII) — ENG diagram (page 1)
Fig. 1

Usage 1. Put the filter bag on the fan. The bag must be placed parallel to the side panels of the device with a dart towards the body. Do it carefully. The filter bag should be placed along the whole surface of the fan. 2. Place the device on a stable, flat surface. The side with the grill must be facing you. Make sure that the bag is fixed evenly and does not fall under the side panel of the device. 3. Before switching on, make sure that there are no foreign objects between fan blades. 4. Insert the plug into a mains socket 220V. Use the switch located on the side panel of the dust collector to turn it on and off. To adjust power, use the rpm governor on the wire. After the first switching on, it is recommended to lift the dust collector and make sure that the bag is puffed and nothing disrupts the air flow. Procedure of switching on: turn the rpm governor clockwise until it locks. Turn the switch to the ON position. Move the regulator counterclockwise to control speed. In order to turn off the device, turn the switch to the OFF position. 5. Work in the area of the dust collector fan impeller and approximately 1.5 cm away from the edge of the grill to the center.

Kaitstud / Secured by https://mereneid.eu/

Page 2 of the Max Desktop (Ultimate VII) user manual — ENG
Pagina 2 · clicca per ingrandire
Pagina 2

ENG

  • Safety measures
  • Do not allow hands or foreign matter entering into the moving blades
  • of the fan.
  • When you need to switch the dust collector off, pull the plug, not the electrical cord.
  • Do not use it with wet towels and water.
  • Do not use the cable as a handle for carrying.
  • Disconnect the dust collector from the outlet during every bag handling operation.

Care Keep the dust collector body clean. Regularly remove dust from the blades and the base of the fan impeller using a soft brush or compressed air. Do not use solvent or other aggressive liquids (e.g. lacquer removal liquid) to clean the device.

The dust collector includes a multi-layer filter bag for collecting dust. Its purity determines the efficiency of the device. Clean dry bag must be used for the dust collector to provide correct functioning.

Change the filter bag for a clean one before starting the working day. Wash the bag to clean it from dust. Manual or delicate machine washing with water temperature of not more than 40 degrees is permitted. During active operation it is recommended to change the filter-bag at least once a day. Service life of bag is 1.5-2 months.

Max Desktop (Ultimate VII) — ENG diagram (page 2)
Fig. 2

WHAT IS THE RISK OF INCORRECT MAINTENANCE OF THE FILTER BAG? Watch the video youtu.be/AqJIDO8xMOs QR code link

  • How to enable the subtitles in the video:
  • Press the gear wheel symbol and in the drop down menu click Subtitles.
  • In the next menu you can choose the language of subtitles

KEEP THE DEVICE CLEAN. The neatness of your equipment will emphasize your professionalism in the eyes of your clients.

Kaitstud / Secured by https://mereneid.eu/

Page 3 of the Max Desktop (Ultimate VII) user manual — ENG
Pagina 3 · clicca per ingrandire
Pagina 3

ENG

  • Specifications
  • Airflow: up to 220 CFM (up to 401 m 3 /h).
  • Noise: up to 55dB.
  • Mains voltage: 220V.
  • Frequency: 50/60 Hz.
  • Impeller speed: up to 2500 rpm.
  • Maximum capacity: up to 76W.
  • Dimension: L*W*H 330*320*175 mm.
  • Weight: 1,8 kg for models without pad, 2,1 kg for padded models.
  • Warranty does not cover
  • Damages caused by incorrect operating conditions, and operation under conditions and for purposes not envisaged by the manufacturer.
  • Mechanical and thermal damage of the dust collector and its parts.
  • Water-related damage.
  • Goods with traces of unauthorized repairs.
  • The filter bag.

Possible problems and solutions

Problem descriptionProblem source. Solution The dust collector does not turn onMake sure that the outlet you connected the device to is in good working condition. Make sure that the mains cord is inserted into the mains, the governor part is set to ON until it locks and the switch is set to ON. If this does not help to fix the problem, contact the manufacturer via e-mail: i@ max4u.ru During operation, dust leaves the filter bag designed to collect dustIt is necessary to replace the bag with a clean one. We recommend you to use a clean filter bag every time before you start work and replace it at least once a day or – if necessary – more often. (See washing instructions in Section «Care») Dust leaves the filter bag after its cleaningThe filter bag fabric has lost its filter properties. Wash and dry it again (washing instructions in Section «Care»). If this does not help, you need to replace the filter bag. The dust collector collects dust only partially• Install a clean dry filter bag. • Make sure that the filter bag of the dust collector is spread evenly and nothing disrupts the air flow. If not, remove the obstacle or spread the bag. • Try to work so that there are no obstacles between the dust source and the grill. It is not permitted to shut off the air flow with your hands or with the hands of the client. • It is necessary to chip nails above the grill, in the area located 1.5 cm from the edge of the grill inside. • Try to keep the client’s hand as close to the grill of the dust collector as possible. • If all the above-mentioned did not help, reduce the speed of rotation of a milling cutter (during hardware manicure) to 15000-20000 rotations

Kaitstud / Secured by https://mereneid.eu/

Riparazione

Risoluzione dei problemi

Problemi comuni, cause probabili e soluzioni.

ProblemaPossibile causaSoluzione
The dust collector does not turn onMake sure that the outlet you connected the device to is in good working condition. Make sure that the mains cord is inserted into the mains, the governor part is set to ON until it locks and the switch is set to ON. If this does not help to fix the problem, contact the manufacturer via e-mail: i@ max4u.ru p.3
During operation, dust leaves the filter bag designed to collect dustIt is necessary to replace the bag with a clean one. We recommend you to use a clean filter bag every time before you start work and replace it at least once a day or – if necessary – more often. (See washing instructions in Section «Care») p.3
Dust leaves the filter bag after its cleaningThe filter bag fabric has lost its filter properties. Wash and dry it again (washing instructions in Section «Care»). If this does not help, you need to replace the filter bag. p.3
The dust collector collects dust only partially• Install a clean dry filter bag. • Make sure that the filter bag of the dust collector is spread evenly and nothing disrupts the air flow. If not, remove the obstacle or spread the bag. • Try to work so that there are no obstacles between the dust source and the grill. It is not permitted to shut off the air flow with your hands or with the hands of the client. • It is necessary to chip nails above the grill, in the area located 1.5 cm from the edge of the grill inside. • Try to keep the client’s hand as close to the grill of the dust collector as possible. • If all the above-mentioned did not help, reduce the speed of rotation of a milling cutter (during hardware manicure) to 15000-20000 rotations p.3

Fai una domanda su Max Desktop (Ultimate VII)

I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Nessuna domanda ancora per il dispositivo Max Desktop (Ultimate VII)

Invia la prima domanda: risponderanno altri possessori o il nostro team.

Documento originale

Max Desktop (Ultimate VII) manuale in PDF

31 pagine·502 KB·Computer·PDF
Clicca su qualsiasi pagina in alto per aprirla qui
Pagina 1 / …
100%
Caricamento pagine…