
HT-SB150
EN DE PL FR IT ES



CAUTION
DO NOT OPEN
Please, read these safety instructions and respect the following warnings before the appliance is operated:
The lightning fl ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi cient magnitude as to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
In order to prevent fi re always keep candles and other open fl ames away from this product.

Cd

The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG,. Inc.
The terms HDMI and HDMI High-Defi nition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing, LLC in the United States and other countries.

Inputs/Outputs
1 2 3 4 5

4. PREVIOUS – Press to return to the previous track. 5. – Press to temporarily pause a playback. Press it again to resume the playback. Hold down this button for 3 seconds to disconnect bluetooth. 6. EQUALIZER – press to switch be- tween preset sound modes (Music/ Movie/News) 7. MUTE – Press to temporarily switch off the sound. Press it again to switch it on. 8. BT – Press to enter the BT (Bluetooth) mode. 9. NEXT – Press to return to the previous track. 10. OPTICAL/ARC – Press to enter the OPTICAL IN mode or ARC mode.

A: Normal Placement (A1 - Attach the silicone feet to the bottom of the soundbar. Place Soundbar on leveled surface in front of TV.) B: Wall Mounting
Insert the battery into the remote control. Point the remote control at the remote sensor on the front panel. The remote control works within a distance of about 8 metres from the sensor and within an angle of about 30 degrees from the left and right side.
BATTERY INSTALLATION
NOTE :
– Installation must be carried out by
qualifi ed personnel only. Incorrect assembly can result in severe personal injury and property damage (if you intend to install this product yourself, you must check for installations such as electrical wiring and plumbing that may be buried inside the wall). It is the installer’s responsibility to verify that the wall will safely support the total load of the unit and wall brackets. – Additional tools (not included) are
required for the installation. – Do not overtighten screws. – Keep this instruction manual for future
reference. – Use an electronic stud fi nder to check
the wall type before drilling and mounting.


the volume output (VOL +/- and MUTE) of the sound bar.
– Connect the HDMI cable (not included)
– Firmly fi x one dowel into each hole
in the wall and then insert screws into them.
Connections
ARC OPTICAL LINE IN UPGRADE ~AC IN
OPTICAL input
ARC OPTICAL LINE IN UPGRADE ~AC IN
The ARC (Audio Return Channel) function allows you to send audio from your ARC- compliant TV to your sound bar through a single HDMI connection. To enjoy the ARC function, please ensure your TV is both HDMI-CEC and ARC compliant and set up accordingly. When correctly set up, you can use your TV remote control to adjust

A. Use a RCA to 3.5mm audio cable (not
included) to connect the TV’s audio output sockets to the LINE IN socket on the unit. B. Use a 3.5mm to 3.5mm audio cable
over 15 minutes, it will automatically switch to Standby mode.
(not included) to connect the TV’s or external audio device headphone socket to the LINE IN socket on the unit. TIP: When you use the headphone output on the TV set, you will be able to adjust the volume level directly using the TV remote control.
Press the button on the unit repeatedly or press the LINE, BT (Bluetooth), OPT/ARC buttons on the remote control to select the desired mode.
– Press the + / - buttons on the unit or

on the remote control to adjust the volume. – If you wish to turn the sound off ,
press the MUTE button on the remote control. Press the MUTE button again or press the +/- buttons on the unit or on the remote control to resume normal listening.

While in HDMI ARC/OPTICAL mode, if there’s no sound output from the unit, you may need to activate PCM signal output on your source device (eg. TV, DVD or Blu-ray player).
button on the remote control for 3 seconds.
The fi rst time you connect your Bluetooth device to this player, you need to pair your device to this player. NOTE:
– The operational range between this
player and a Bluetooth device is approximately 8 meters (without any object between the Bluetooth device and the unit). – Before you connect a Bluetooth device
to this unit, ensure you know the device’s capabilities. – Compatibility with all Bluetooth de-
– If the connected Bluetooth device
vices is not guaranteed. – Any obstacle between this unit and
supports Advanced Audio Distribution Profi le (A2DP), you can listen to the music stored on the device through the soundbar‘. – If the device also supports Audio Video
a Bluetooth device can reduce the operational range. – If the signal strength is weak, your
Bluetooth receiver may disconnect, but it will re-enter pairing mode automatically. 1. Turn on the soundbar by pressing the standby button.
Remote Control Profi le (AVRCP), you can use the soundbar‘s remote control to play music stored on the device. 1. Pair your device with the player.
– To pause/resume play, press the button on the remote control. – To skip to a track, press the / buttons on the remote control.
To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this unit, review the following before requesting service.

No power Ensure that the AC cord is properly connected. Ensure that there is power at the AC outlet. Press standby button on the remote control or soundbar to turn the soundbar on.
Connect a diff erent source device (TV, Blu-ray player, etc) to see if the buzzing persists. If it does not, the problem may be with the original device. Connect your device to a diff erent input on the soundbar.
I can’t fi nd the Bluetooth name of this unit on my Bluetooth device Ensure the Bluetooth function is activated on your Bluetooth device. Re-pair the unit with your Bluetooth device.
No sound Increase the volume. Press Volume Up on the remote control or on the right side of the soundbar. Press MUTE on the remote control to ensure the soundbar is not muted. Press source buttons to select a diff erent input source. When using either of the Digital input, if there is no audio:
This is a 15 mins power off function, one of the ERPII standard requirement for saving power When the unit’s external input signal level is too low, the unit will be turned off automatically in 15 minutes. Please increase the volume level of your external device.
– Try setting the TV output to PCM or – Connect directly to your Blu-ray/other
source, some TVs do not pass through digital audio. Your TV may be set to variable audio output. Confi rm that the audio output setting is set to FIXED or STANDARD, not VARIABLE. Consult your TV’s user manual for more detailed information. If using Bluetooth, ensure that the volume on your source device is turned up and that the device is not muted.
Remote control does not work Before you press any playback control button, fi rst select the correct source. Reduce the distance between the remote control and the unit. Insert the battery with its polarities (+/-) aligned as indicated. Replace the battery. Aim the remote control directly at the sensor on the front of the unit.
I hear buzzing or humming Ensure all cables and wires are securely connected.


Pagine di riferimento in questo manuale: produttore, supporto e download.
I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.
Invia la prima domanda: risponderanno altri possessori o il nostro team.