Manuale d’uso / di manutenzione del prodotto network services del fabbricante Black Box
Vai alla pagina of 17
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500 ) FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746 Mailing address: Black Box Corporation , 1000 Park Drive, Lawrence, PA 15055-1018 Web site: www.
FCC ST A TEMENT 1 FEDERAL COMMUNICA TIONS COMMISSION AND INDUSTR Y CANADA RADIO FREQUENCY INTERFERENCE ST A TEMENTS This equipment generates, uses, and can radiate radio-frequency energy , and if not installed and used properly , that is, in strict accordance with the manufacturer’ s instructions, may cause inter ference to radio communication.
PSD-4 AND PSD-8 2 INSTRUCCIONES DE SEGURIDAD (Normas Oficiales Mexicanas Electrical Safety Statement) 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.
TRADEMARKS 3 TRADEMARKS USED IN THIS MANUAL AS/400 is a registered trademark of International Business Machines Corporation. Any other trademarks mentioned in this manual are acknowledged to be the pr oper ty of the trademark owners.
PSD-4 AND PSD-8 4 1. Specifications Number of Sub-Channels — PSD-4: 4 PSD-8: 8 Channel Configuration — Lowest Priority: Sub-channel 1 Highest Priority: PSD-4: Sub-channel 4 PSD-8: Sub-channel 8 Su.
CHAPTER 2: Introduction 5 2. Introduction The Programmable Sharing Device enables up to 4 (TL304A) or 8 (TL305A) modems or terminals to share a master modem, multiplexor , or computer port in an asynchronous or synchronous multipoint environment. (Asynchronous and synchronous equipment cannot be mixed on the same PSD.
PSD-4 AND PSD-8 6 3. Installation 3.1 Choosing a Site • The PSD must be installed within five feet (1.5 m) of a grounded AC outlet. • The PSD must be within 50 feet (15 m) of the equipment that will be attached to the main channel and each sub-channel.
CHAPTER 3: Installation 7 T able 1. Printed Circuit-Board Switch and Strap Settings Possible Factory Stap Identity Location Settings Setting Function MAIN DCE/DTE switch DTE DTE Determines the PSD’s Main Channel DCE interface as either DTE (straight connection to a modem) or as DCE (straight connection to a computer or terminal).
PSD-4 AND PSD-8 8 Figure 3. The Printed Circuit Boar d of the PSD-4. Figure 4. The Printed Circuit Boar d of the PSD-8..
CHAPTER 3: Installation 9 3.3 System Synchronization A SYNCHRONOUS M ODE Strap the J6 jumper over the ASYNC pins. All attached equipment must be asynchronous. T urn the BIT RA TE rotary switch (BRI) to the correct system speed. No other adjustments to the PSD are necessar y .
PSD-4 AND PSD-8 10 • BIT RA TE rotar y switch: Set BRI to the correct system speed. • EXT . BUFFER: If any of the devices connected to the sub-channels numbered 1 through 4 are set to internal clock, then switch S1 should be ON.
CHAPTER 4: Operation and T roubleshooting 11 4. Operation and T roubleshooting 4.1 Operation T urn on the rear-panel POWER rocker switch. The front-panel POWER LED will light. The PSD operates automatically . Except for manually disabling a sub-channel, you will not need to attend to the PSD.
PSD-4 AND PSD-8 12 Figure 5. The back panels of the PSD-4 (top) and the PSD-8 (bottom). FUSE POWER: Rocker switch to turn AC power on or off 110/220 VAC Selector: Align either 110 or 220 with the arrow. SCREWS: Loosen these screws to take off the cover of the PSD.
CHAPTER 5: T echnical Guide 13 5. T echnical Guide 5.1 Control Signals M AIN C HANNEL C ONTROL S IGNALS RTS (DCD) • In R TS/DCD contention mode: follows R TS (DCD) of the selected sub-channels. • In Data Contention mode: ON if one of the sub-channels R TS (DCD) is ON.
PSD-4 AND PSD-8 14 Figure 6. Main Channel DTE with Sub-Channel DCE. Figure 7. Main Channel DTE with Sub-Channel DTE..
CHAPTER 5: T echnical Guide 15 Figure 8. Main Channel DCE with Sub-Channel DCE. Figure 9. Main Channel DCE with Sub-Channel DTE..
1000 P ark Drive • Lawrence, P A 15055-1018 • 724-746-5500 • F ax 724-746-0746 © Cop yright 1998. Black Box Corporation. All rights reserved..
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Black Box Black Box network services è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Black Box Black Box network services - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Black Box Black Box network services imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Black Box Black Box network services ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Black Box Black Box network services, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Black Box Black Box network services.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Black Box Black Box network services. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Black Box Black Box network services insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.