

1 Safety Instructions
Please read these operating instruc- tions carefully. Above all please observe the safety instructions on the initial pages of these operating instructions! Please keep these operat- ing instructions for future reference. Pass them on to any subsequent owner of the appliance.
A Rating plate B Stainless steel soleplate C Steam exit holes D Spray nozzle E Filling aperture F Steam selector G Jet button H Spray function button J Power indicator K Mains cord L Heel M Cord storage N Temperature selector O Transparent water reservoir P Measuring beaker
a “Cold” setting b Synthetics c Silk/wool d Cotton/linen

that it takes a while for the soleplate to cool down. Only when the power indicator light comes on again has the soleplate reached the cooler tempera- ture.
0 Set the steam selector (Figure 1/F) to position „ “ (Figure 4/A). 0 Turn the temperature selector (Figure 1/N) to the desired tempera- ture.
Technical Data
Filling the Steam Iron (Figure 3) The water reservoir should only be filled when the plug has been removed from the socket. 0 Set the steam selector to position „ “ = dry iron (Figure 4/A) and hold the appliance upright. 0 Fill the water reservoir at most to the “MAX” mark. To do this, you can use the measuring beaker supplied (Figure 1/P).
Water Quality You can use tap water up to 3 mmol/I 17° dH water hardness level. Your local Water Authority can advise you on the hardness of the water in your area. If the water from your tap is harder than the above, please use distilled water available from a chemist or a 50:50 mixture of tap water and distilled water.
Setting the Temperature (Figure 2) Please note the internationally appli- cable care symbols on garment labels. On good quality garments they indi- cate the correct ironing temperatures. The ironing table indicates which tem- perature is most appropriate for a par- ticular type of fabric. We recommend sorting the washing first. Start with materials that require low temperature ironing (e.g. PERLON). Follow on by ironing materials that require progres- sively higher temperatures. In this way you avoid damaging sensitive fabrics by using too high a temperature. When switched on, the power indicator lamp lights up (Figure 1/J); it goes out when the temperature set has been reached. However, if the temperature selector (Figure 1/N) is turned back, please note
When using for the first time, please note: 0 Fill the reservoir with water; set the steam selector (Figure 1/F) to maxi- mum position (Figure 4/B). 0 Heat the appliance and place it with the soleplate facing downwards on an iron rest or plate (Figure 5) to allow the water to steam through and activate the steam chamber.

3 You will obtain optimal steaming results and the noise produced by the steaming will be steadier after the water reservoir has been filled and drained three times.
Steaming hanging items of clothing 0 Turn the temperature selector (Figure 1/N) to the “MAX” position and wait until the power indicator (Figure 1/J) goes out. 0 Hang the article concerned on a hanger and hold the steam iron at a distance of 10 – 20 cm from the material. 0 Now press the steam jet button (Figure 1/G). Wait at least 5 seconds before pressing the button again.
Ironing with Steam To steam iron, set the temperature selector (Figure 1/N) to the required fabric type and wait until the power indicator (Figure 1/J) goes out - only then set the steam selector (Figure 1/F) to the desired position (Figure 4/B). You will find which temperature setting (fabric type) matches which steam set- ting in the ironing table. As soon as the steam iron is held horizontally steam begins to form. When the steam iron is set upright again the steam supply stops automatically.
1 Warning: Do not attempt to freshen up clothing whilst it is still being worn. Risk of burning!
Drip Stop The steam iron has an automatic drip stop function. The drip stop immedi- ately interrupts the creation of steam if the temperature selected is too low.
Spray Function (Figure 6/A) The first time you use the appliance, or if you have not used it for a long time, you will need to press the spray function button (Figure 1/H) several times before water comes out of the spray nozzle (Figure 1/D). You can also use the spray function when dry iron- ing.
Remove the plug from the socket! Set the temperature selector (Figure 1/N) to the “Cold” position (Figure 2/a) and the steam selector (Figure 1/F) to position „ “ (Figure „ “4/A). Empty out remaining water (Figure 7). Store the appliance standing upright. To store properly wrap the mains cord around the cord storage (Figures 1/M and 8).
Super Steam Jet Function (Figure 6/B) The super steam jet function is of valuable assistance when ironing, for example, creases, embroidery etc. You can trigger the additional steam jet both when steam ironing and when dry ironing. 0 Set the temperature selector (Figure 1/N) to the “MAX” position and wait until the correct temperature has been reached, i.e., until the power indi- cator (Figure 1/J) goes out. 0 Raise the steam iron a little away from the material and press the steam jet button (Figure 1/G). Always wait another 5 seconds before pressing the steam jet button again.
The steam iron has an automatic decal- cification feature, which significant slows down the deposit of limescale in the steam chamber.
1 The steam iron must not be des- caled! Neither vinegar nor proprie- tary brands of descaler must be filled into the water reservoir!

Cleaning As a precaution we recommend clean- ing every three months. 0 Unplug from the mains. 0 Set the steam selector (Figure 1/F) to position „ “ (Figure 4/A). 0 Fill the water reservoir (Figure 1/O) with clear water to the “MAX” mark. 0 Set the temperature selector (Figure 1/N) to “MAX”. 0 Insert the plug into the socket. 0 Wait until the power indicator (Figure 1/J) goes out. 0 Set the steam selector (Figure 1/F) to position (Figure 4/C). 0 Place the appliance horizontally over a sink. 0 Press the steam selector (Figure 1/F) for at least 1 minute. Water is flowing out of the steam exit holes. Your steam iron is now ready for use again.
of water and vinegar or with a non- abrasive cleaning agent. – When dry ironing fluff can enter the
steam chambers and carbonise. This can lead to stains as the water passes through. Therefore also clean the inside of the water reservoir. Fill it with water and gently shake the steam iron. Then pour the water out. • the soleplate is rough or furred? – The iron temperature was set too
high. – Select the correct ironing tempera-
ture for the fabric (see ironing table).
2 Packaging material The packaging materials are environ- mentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PEPS
What to do, if ...
The symbol W on the product or on its packaging indicates that this prod- uct may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and elec- tronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste han- dling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you pur- chased the product.
reduced amounts of vapour are nor- mal because it is absorbed by the dry air before condensing. – Emptying the filled water reservoir
can wash out fluff. Remove the mains cord and tip the filled appli- ance forwards at an angle (Figure 7) so that the water can run out of the filling aperture. • drops of water are coming out of the steam exit holes? – Do not set the steam selector to
another position than „ “ until the temperature for steam ironing has been reached. If the temperature has been set too low for steam ironing increase the setting. • stains appear on the washing while ironing? – Clean the steam iron. Rub the sole-
plate while still warm with a mixture
I possessori del prodotto e il nostro team di solito rispondono entro 24 ore, e la tua domanda sarà utile anche ad altri.
Invia la prima domanda: risponderanno altri possessori o il nostro team.