Manuale d’uso / di manutenzione del prodotto G3700 del fabbricante Zenoah
Vai alla pagina of 15
G3700 G B GB-1 G3700 OWNER’S MANUAL CHAIN SA W G B 848C6493A1 (704).
G3700 GB-2 EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS Read operator's instruction book bef ore operating this machine. W ear head, ey e and ear protection. Use the chain saw with two hands. Wa r ning! Danger of kickbac k. Read, understand and f ollow all w arnings.
G3700 G B GB-3 Contents 1. For Safe Operation ................................................................... 4 2. Explanation of Symbols on the Machine .................................. 6 3. Installing Guide Bar and Saw Chain ...................
G3700 GB-4 10. Keep all parts of your body away from the saw chain when the engine is run- ning. 11. Before you start the engine, make sure the saw chain is not contacting anything. 12. Always carry the chain saw with the engine stopped, the guide bar and saw chain to the rear , and the muf fler away from your body .
G3700 G B GB-5 (3) Make certain that the area in which you are cutting is fr ee fr om obstruc- tions. Do not let the nose of the guide bar contact a log, branch, or any other obstruction which could be hit while you are operating the saw . (4) Cut at high engine speeds.
G3700 GB-6 2. Explanation of Symbols on the Machine W ARNING For safe operation and maintenance, symbols are car ved in relief on the machine. According to these indications, please be careful not to make any mistake. The screw under the “H” stamp is The High-speed adjustment scr ew .
G3700 G B GB-7 Po w er unit Bar protector Guide bar Saw chain Plug wrench Screwdriv er for carb uretor adjustment 4. Fit the chain cover to the power unit and fasten the nuts to finger tightness.
G3700 GB-8 4. Fuel and Chain Oil ■ FUEL W ARNING • Gasoline is very flammab le. A v oid smoking or bring- ing any flame or sparks near fuel. Make sure to stop the engine and allo w it cool bef ore refueling the unit. Select outdoor bare gr ound for fueling and mo ve at least 3 m (10 ft) a wa y from the fueling point bef ore starting the engine.
G3700 G B GB-9 5. When engine has ignited first, push in the choke knob to the first-stage position and pull the starter again to start the engine. 6. Allow the engine to warm up with the throttle lever pulled slightly . W ARNING K eep clear of the sa w chain as it will start r otating upon starting of engine .
G3700 GB-10 Normal operating mode Anti-freeze mode Cylinder cov er “Sunshine” mark “Snow” mar k Switch Choke knob Icing cap 1. H and L needles are r estricted within the number of turn as shown below . H needle : -1/4 L needle : -1/4 2. Start the engine and allow it to war m up in low speed for a few minutes.
G3700 G B GB-11 6. Sawing W ARNING • It is not necessary to force the saw into the cut. Apply only light pressur e while running the engine at full throttle. • When the saw chain is caught in the cut, do not attempt to pull it out by force, but use a wedge or a lever to open the way .
G3700 GB-12 7. Maintenance Oiling por t Grease por t Sprock et Oiling por t A log lying on the gr ound Saw down halfway , then roll the log over and cut from the opposite side. A log hanging off the ground In area A, saw up fr om the bottom one-third and finish by sawing down from the top.
G3700 G B GB-13 Place the file on the cutter and push straight forward. Keep the file position as illustrated. After each cutter has been filed, check the depth gauge and file it to the proper level as illustrated. 2. Fuel filter (a) Using a wire hook, take out the filter fr om the filler port.
G3700 GB-14 of the bar rail. Apply a ruler to the bar and the out- side of a cutter . If a gap is observed between them, the rail is normal. Otherwise, the bar rail is wor n. Such a bar needs to be corrected or r eplaced. 9. T r oubleshooting Guide Case 1.
G3700 G B GB-15 11. Specifications Po wer unit: Displacement (cm 3 ): ............................................. 37.2 Fuel: ................ Mixtur e (Gasoline 50 : T wo-cycle oil 1) ............................. (when using ZENOAH genuine oil) Fuel tank capacity (cm 3 ): .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Zenoah G3700 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Zenoah G3700 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Zenoah G3700 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Zenoah G3700 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Zenoah G3700, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Zenoah G3700.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Zenoah G3700. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Zenoah G3700 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
