Manuale d’uso / di manutenzione del prodotto G3100T del fabbricante Zenoah
Vai alla pagina of 28
OWNER / OPERA T OR MANUAL CHAINSA WS T2054-93110 (212) The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. W ARNING Before using our products, please read this manual carefully to understand the proper use of your unit.
.
SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
2. Specifications ■ G3100T Power unit : Displacement ······················································································ 1.
3. Symbols on the machine 5 MADE IN IT AL Y IMPORT ANT ENGINE INFORMA TION THIS ENGINE CONFORMS TO US EP A PH1 FOR SMALL OFF-RO AD ENGINES. ENGINE F AMIL Y : 3E8XS.0304TH ENGINE DISPLACEMENT : 30.1cm 3 MANUF ACTURED: REFER TO O WNER'S MANUMAL FOR MAINTE- NANCE SPECIFICA TIONS AND ADJUSTMENTS.
6 4. For safe operation 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy, or if you are under the influence of alcohol or drugs. 2. Use safety footwear, snug fitting clothing and eye, hearing and head protection devices.
7 4. For safe operation 16. Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building. Exhaust fumes contain dangerous carbon monoxide. 17. Do not operate a chain saw in a tree unless specially trained to do so.
A standard saw unit package contains the items as shown. (SE1) Open the box and install the guide bar and the saw chain to the power unit as follows. The saw chain has very sharp edges. Use thick, protective gloves to avoid injury. 1. Loosen a nut and remove the chain cover.
6. Fuel and chain oil 9 • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m(10ft) away from the fueling point before starting the engine.
6. Fuel and Chain oil container to avoid mixing up with gasoline or other containers. 6. Indicate the contents on outside of container for easy identification. ■ FUELING THE UNIT 1. Untwist and remove the fuel cap. Rest the cap on a dustless place. 2.
■ FUELING THE UNIT (OP1) 1. Remove the fuel tank cap and pour fuel into the tank up to 80% of full capacity. 2. Fasten the fuel cap securely and wipe up any fuel spillage around the unit. 3. Remove the oil tank cap and pour chain oil into the tank. Fasten the cap securely.
12 OP8 7. Operation ■ CHECKING OIL SUPPLY After starting the engine, run the chain at medium speed and see if chain oil is scattered off as shown in the figure. (OP6) The oil tank should become nearly empty by the time fuel in the tank is used up.
4. Make a test cut adjust the H needle for best cutting power, not for maximum speed. ■ CHAIN BRAKE The chain brake is a device designed to stop the saw chain quickly when kickback occured. The brake system equipped on the G3100T units is designed to work automatically by sensing reaction force.
• Before proceeding to your job, read “For Safe Operation” section. It is recommended to first practice sawing easy logs. This also helps you get accustomed to your unit. • It is not necessary to force the saw into the cut. Apply only light pressure while running the engine at full throttle.
should stop immediately with the engine at full speed. If the chain is slow to stop or does not stop then replace the brake band and clutch drum before use. • It is extremely important that the chain brake be checked for proper operation before each use and that the chain be sharp in order to maintain the kickback safety level of this saw.
of bending direction to prevent the guide bar from being caught in the cutaway. ● Cutting an unpillowed log Saw down halfway, then roll the log over and cut from the opposite side. (SA3) ● Cutting a pillowed log In the area A in the picture right above, saw up from the bottom one-third and finish by sawing down from the top.
17 9. Maintenance Make sure to stop the engine before inspecting and/or servicing the unit. ■ DAILY MAINTENANCE SAW CHAIN It is one of the essential factors for smooth and safe operation to keep the cutters always in good condition. It’s time to reform the cutters when; 1.
18 9. Maintenance GUIDE BAR 1. Remove sawdust in the bar groove and the oiling port. (MA5) 2. Grease the nose sprocket from the feeding port on the tip of the guide bar. (MA6) 3. Periodically turn over the guide bar when mounting it to the unit, in order to prevent partial wear.
anything wrong be found, make sure to have it repaired before next usage. ■ MONTHLY MAINTENANCE FUEL FILTER When the engine runs short of fuel supply, check the fuel filter for blockage. (MA9) OIL STRAINER Drain the oil tank and remove the oil strainer located near the spark plug.
20 SPARK ARRESTER RedMax engines are equipped with a spark arresting screen at the exhaust port. Periodically check and keep it in good condition.
21 1 1. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company.
22 1 1. Parts list Fig.1 POWER UNIT G3100T (S/N 0723010001 and up) G3100T.
23 Fig.1 POWER UNIT (S/N 0723010001 and up) G3100T 1 T2050-12110 CYLINDER 1 2 T2050-21110 CRANKCASE 1 3 01252-30530 BOLT 4 4 2870-41111 PISTON 1 5 3319-41210 RING 1 6 3304-41310 PIN 1 7 3310-4.
24 1 1. Parts list Fig.2 CARBBURETOR COMPONENTS & ACCESSORIES (S/N 0723010001 and up) G3100T.
25 Fig.2 CARBBURETOR COMPONENTS & ACCESSORIES (S/N 0723010001 and up) G3100T Key# PART NUMBER DESCRIPTION Q'TY /UNIT NOTE Key# PART NUMBER DESCRIPTION Q'TY /UNIT NOTE 1 T2054-810.
THE CALIFORNIA AIR RESOURCES BOARD AND KOMATSU ZENOAH Co. ARE PLEASED TO EXPLAIN THE EMISSION CONTROL SYSTEM WARRANTY ON YOUR 1995 AND LATER LAWN AND GARDEN EQUIPMENT ENGINE. IN CALIFORNIA, NEW UTILITY AND LAWN AND GARDEN EQUIPMENT ENGINES MUST BE DESIGNED, BUILT AND EQUIPPED TO MEET THE STATE'S STRINGENT ANTI-SMOG STANDARDS.
EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP.
©P rinted in Japan Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratui.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Zenoah G3100T è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Zenoah G3100T - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Zenoah G3100T imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Zenoah G3100T ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Zenoah G3100T, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Zenoah G3100T.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Zenoah G3100T. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Zenoah G3100T insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
