Manuale d’uso / di manutenzione del prodotto G2500 del fabbricante Zenoah
Vai alla pagina of 19
G2500 / G2500 OPS GB-1 G B G2500 G2500 OPS (One-Push-Star t) CHAIN SA WS OWNER’S MANUAL G B 848C1B93A1 (704).
G2500 / G2500 OPS GB-2 EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS Read operator's instruction book before operating this machine. W ear head, ey e and ear protection. Use the chain saw with two hands. Wa r ning! Danger of kickback. Read, understand and follow all warnings.
G2500 / G2500 OPS GB-3 G B Contents 1. For Safe Operation ................................................................... 4 2. Explanation of Symbols on the Machine .................................. 8 3. Installing Guide Bar and Saw Chain .......
G2500 / G2500 OPS GB-4 10. Always hold the chain saw firmly with both hands when the engine is running. Use a firm grip with thumb and fingers encircling the chain saw handles. 11. Keep all parts of your body away from the saw chain when the en- gine is running.
G2500 / G2500 OPS GB-5 G B KICKBACK SAFETY PRECAU- TIONS FOR CHAIN SA W US- ERS W ARNING • Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut.
G2500 / G2500 OPS GB-6 WORKING WITH TREE SERVICE CHAIN-SA WS FROM A ROPE AND HARNESS This chapter sets out working practices to reduce the risk of injury from tree service chainsaws when working at height from a r ope and harness.
G2500 / G2500 OPS GB-7 G B Gaining a good footing at the working position can be assisted by use of a temporary foot stirrup created from an endless sling.
G2500 / G2500 OPS GB-8 2. Explanation of Symbols on the Machine The port to refuel “MIX GASOLINE” Position: Fuel cap The port to top up chain oil Position: Oil cap Setting the switch to the “O” position, the engine stops immediately . Position: Front at the top of the r ear handle Starting the engine.
G2500 / G2500 OPS GB-9 G B Open the box and install the guide bar and the saw chain on the power unit as follows: The saw chain has very sharp edges. Use thick pro- tective gloves for safety . 1. Pull the guard towar ds the front handle to check that the chain brake is not engaged.
G2500 / G2500 OPS GB-10 NOTE NOTE 4. Pour in the rest of gasoline and agitate again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, suf ficient agi- tation is necessary for the engine to last long.
G2500 / G2500 OPS GB-11 G B It is very dangerous to run a chainsaw that mounts broken parts or lacks any par ts. Before starting engine, make sure that all the parts includ- ing bar and chain are installed pr operly . ■ ST ARTING THE ENGINE Normal star t 1.
G2500 / G2500 OPS GB-12 • When pulling out the rope, large clanging is produced. W ith this clanging, stop pulling out the r ope at once. This sound notifies that One-push-start has been set. • Don’ t pull out the rope excessively or don’ t pull it out without load by the starter only , otherwise a starter failure will occur .
G2500 / G2500 OPS GB-13 G B • When the brake operates, release the thr ottle lever to slow down the engine speed. Continuous opera- tion with the brake engaged will generate heat from the clutch and may cause trouble. • At machine inspection prior to each job, check the operating condition of the brake following the steps.
G2500 / G2500 OPS GB-14 A log lying on the ground Saw down halfway , then roll the log over and cut fr om the opposite side. A log hanging off the ground In area A, saw up fr om the bottom one-third and finish by sawing down from the top. In ar ea B, saw down fr om the top one-third and finish by sawing up fr om the bot- tom.
G2500 / G2500 OPS GB-15 G B When returning the filter , use a pinch not to be folded the suc- tion pipe. 3. Oil filter 1. With a wire hook, take out the oil filter fr om the feeding port. 2. W ash the filter with gasoline. When returning the filter , use a pinch not to be folded the suc- tion pipe.
G2500 / G2500 OPS GB-16 8. Recoil Starter • For recoil maintenance, when attaching or detaching the starter of One-push-star t model, the select lever should be in the position of the rear side (G2500 One-push-start only). • Don't pull the starter when detaching it from the unit.
G2500 / G2500 OPS GB-17 G B side of a cutter . If a gap is observed between them, the rail is normal. Otherwise, the bar rail is wor n. Such a bar needs to be corrected or r eplaced.
G2500 / G2500 OPS GB-18 11. Specifications Cutting head: <Sprocket bar> Sprocket: .................................................................. 6T Chain speed at max. power ......................... 17.1 (m/s) Guide bar T ype: .............
G2500 / G2500 OPS GB-19 G B 12. Limited warranty Should any failure occur on the pr oduct under normal operating conditions within the applicable warranty pe- riod, the failed part will be replaced or r epaired fr ee of charge by a ZENOAH authorized dealer .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Zenoah G2500 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Zenoah G2500 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Zenoah G2500 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Zenoah G2500 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Zenoah G2500, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Zenoah G2500.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Zenoah G2500. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Zenoah G2500 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
