Manuale d’uso / di manutenzione del prodotto G2000T del fabbricante Zenoah
Vai alla pagina of 16
G2000T GB-1 G B G2000T CHAIN SA W OWNER’S MANUAL G B 848C0593A0 (704).
G2000T GB-2 EXPLANA TION OF SYMBOLS AND SAFETY W ARNINGS Contents 1. For Safe Operation ................................................................... 4 2. Explanation of Symbols on the Machine .................................. 8 3. Installing Guide Bar and Saw Chain .
G2000T GB-3 G B 1. For safe operation W ARNING This chainsaw has been especially designed for tree maintenance and should therefor e only be used by trained operators when working on trees.
G2000T GB-4 20. Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building. Exhaust fumes contain dan- gerous carbon monoxide. 21. Do not operate the chain saw in a tree unless specially trained to do so.
G2000T GB-5 G B W ORKING WITH TREE SERVICE CHAIN-SA WS FROM A R OPE AND HARNESS This chapter sets out working practices to reduce the risk of injury from tree service chainsaws when working at height from a r ope and harness.
G2000T GB-6 Gaining a good footing at the working position can be assisted by use of a temporary foot stirrup created from an endless sling. Starting the saw in the tree When starting the saw in the t.
G2000T GB-7 G B 2. Explanation of Symbols on the Machine The port to refuel “MIX GASOLINE” Position: Fuel cap The port to top up chain oil Position: Oil cap Setting the switch to the “O” position, the engine stops immediately . P osition: Front at the top of the rear handle Starting the engine.
G2000T GB-8 Open the box and install the guide bar and the saw chain on the power unit as follows: The saw chain has very sharp edges. Use thick pro- tective gloves for safety . 1. Pull the guard towar ds the fr ont handle to check that the chain brake is not engaged.
G2000T GB-9 G B 4. Pour in the rest of gasoline and agitate again for at least one minute. As some oils may be difficult to agitate de- pending on oil ingredients, sufficient agitation is nec- essary for the engine to last long.
G2000T GB-10 6. When engine has ignited, first turn in the choke knob to the first-stage position (2) and then pull the starter again to start the engine. 7. Allow the engine to warm up with the throttle lever pulled slightly . Keep clear of the saw chain as it will start rotating upon starting of engine.
G2000T GB-11 G B • When the brake operates, release the thr ottle lever to slow down the engine speed. Continuous opera- tion with the brake engaged will generate heat from the clutch and may cause trouble. • At machine inspection prior to each job, check the operating condition of the brake following the steps.
G2000T GB-12 ■ FELLING A TREE 1. Decide the felling direction considering the wind, lean of the tree, location of heavy branches, ease of completing the task after felling and other factors. 2. While clearing the area ar ound the tr ee, arrange a good foothold and retr eat path.
G2000T GB-13 G B 3. Oil filter 1. With a wire hook, take out the oil filter fr om the feed- ing port. 2. W ash the filter with gasoline. When returning the filter , use a pinch and make sure that the pipe is not folded and the filter is placed at the bottom of the tank as shown in the picture.
G2000T GB-14 ■ SA W CHAIN It is very impor tant for smooth and safe operation to always keep the cutters sharp. The cutters need to be sharpened when: • Sawdust becomes powder -like. •Y ou need extra force to saw in. • The cut path does not go straight.
G2000T GB-15 G B 9. T r oubleshooting Guide Case 1. Starting failure Make sure the icing pr evention system is not working. Check fuel for water or substandard mix- ture. Replace with proper fuel. Check for engine flooding. Check spark ignition. Remove and dry the spark plug.
G2000T GB-16 Limited warranty Should any failure occur on the pr oduct under normal operating conditions within the applicable warranty pe- riod, the failed part will be replaced or repair ed free of charge by a ZENOAH authorized dealer .
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Zenoah G2000T è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Zenoah G2000T - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Zenoah G2000T imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Zenoah G2000T ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Zenoah G2000T, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Zenoah G2000T.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Zenoah G2000T. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Zenoah G2000T insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
