Manuale d’uso / di manutenzione del prodotto CRW8824IX Series del fabbricante Yamaha
Vai alla pagina of 44
XY851A0 Y AMAHA CORPORA TION Printed in Malaysia OW NER’S MA NUAL BEDIENUNGSANLEITUNG MODE D’EMPLOI MANUAL DE INSTRUCCIONES C D - R/RW Drive C R W 8824I X SERIES C R W 8824I X SERIES OW NER’S MA.
COMPLIANCE INFORMA TION ST A TEMENT (DECLARA TION OF CONFORMITY PROCEDURE) Responsible P arty: Y amaha Corporation of Amer ica Address: 6600 Or angethor pe A v e.
CA UTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure . Laser Diode Properties Material: GaAlAs Wa velength: 780-787 nm Emission Duration: Contin uous Laser Output Po wer: Less than 44.
.
i English OWNER’S MANUAL C D- R/RW Drive C R W 8824IX SERIES C R W 8824IX SERIES C D- R/RW Drive.
ii SAFETY PRECAUTIONS PLEASE READ CAREFULL Y BEFORE PROCEEDING These precautions explain how to use the device correctly and safely , thereby preventing injur y to yourself or to others.
iii CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to yourself or others, or damage to the instrument or other property .
iv ■ About CD-R/RW discs Please read the follo wing regarding the handling of CD-R/R W discs. 1. Do not e xpose discs to e xcessiv e heat such as in direct sunlight or near a heater . Also av oid keeping them in a humid place . 2. Do not touch disc surf aces.
v T able of Contents ©2000 Y amaha Corporation. All Rights Reserved. This document may not, in whole or in part, be copied, photocopied, r eproduced, translated, transmitted or r educed to any electronic medium of machine readable for m without prior consent in writing from Y amaha.
1 Introduction Features of the CRW8824IX Drive Easy setup Implementation of an IEEE1394 interface (also known as Fir eW ire or i.LINK) eliminates the need for drive configurations (device ID, termination, and so on). Y ou can connect and start using the drive whenever you wish without restar ting your computer .
Introduction About IEEE1394 IEEE1394 is an industry standard appr oved by IEEE (Institute of Electrical and Electronics Engineers). The serial inter face has a broad bandwidth and is fast enough to bidir ectionally transfer large amounts of digital video and audio data between electr onic devices including computer peripherals.
3 Before Use System Requirements In order to use the CR W8824IX drive, your computer system will need to meet the following set of requir ements. n The CR W8824IX drive may not write at a maximum speed depending on your computer’ s system configuration.
Before Use n For latest information about approved IEEE1394 interface car ds, check Y AMAHA CD-R/R W Drive web site at http://www .yamaha.co.jp/english/product/computer/.
Before Use 5 Supported Discs The CR W8824IX can write to discs that carry the following logos. CD-R discs *1 The CR W8824IX can write to these discs at 8X, 6X, 4X, and 1X speeds. These discs can be played back in a CD-ROM drive or a CD player . n When writing at 8X or 6X speeds, please use “high-speed writing capable” discs.
Before Use About CD-ROM A CD-ROM disc is a compact disc containing high-density r ead-only data. It has many applications, including the playback of music and video, the ar chiving of data, as well as on-line documentation.
7 Setup Flowchart The flowcharts below show the pr ocedure for setting up the CR W8824IX drive. For easy cross-r eferencing, each step includes r elevant pages in this manual. Windows Users S TEP 1 S TEP 2 S TEP 4 S TEP 5 S TEP 3 STEP 3-2 STEP 3-1 Yes Yes No No 1 T urn your computer and the drive both on (before connection).
Setup Flowchart 8 Macintosh Users S TEP 1 S TEP 2 S TEP 3 Yes 1 T urn your computer and the drive both on (before connection). 2 Connect your computer and the drive using an IEEE1394 interface cable that came with the drive.
9 Setup Procedures Serial Number Once you have taken the CR W8824IX drive out of its packaging, you should immediately note down the serial number found at the r ear of the drive under the bar code. Y ou may need to refer to this number when r equesting Customer Support services.
Setup Procedures Connections Befor e connecting the CR W8824IX drive and the computer as described below , make sure that you have installed appr opriate CD writing software (P . 3, 4). If you newly install the CD writing softwar e, first disconnect all IEEE1394 devices fr om your computer .
Setup Procedures 4 Connect the other end of the power cable to an AC outlet. n The power unit inside the CR W8824IX will automatically adjust itself to the local voltage (100 to 240 volts). 5 Press the POWER switch on the drive’ s front panel to turn the unit on.
Setup Procedures 6 Connect either IEEE1394 port on the drive’ s rear panel to an IEEE1394 (FireWire or i.LINK) port on the computer using the supplied IEEE1394 interface cable (with a 6-pin connector at each end).
Setup Procedures Connection to a Macintosh computer 1 2 1 2 IEEE1394 (FireWir e) por ts IEEE1394 ports IEEE1394 interface cable CRW8824IX rear panel n Y ou can connect the interface cable to either IEEE1394 port on the CR W8824IX drive. n The IEEE1394 standard defines the maximum cable length of a single inter face cable as 4.
Setup Procedures Notes on Connecting IEEE1394 Devices Remember the following notes when connecting the CR W8824IX drive to the host computer along with other IEEE1394 devices. ● For optimum performance of writing a CD, connect the CR W8824IX directly or solely to the host computer .
Setup Procedures Restricted Connections A void creating a looped connection that sends data output fr om a device back to the same device. The illustration below shows an example of such a loop (at the host computer).
Setup Procedures Verifying the Hardware Installation After connecting the CR W8824IX drive to the computer (or an IEEE daisy-chain or tr ee), you can verify that the drive is correctly r ecognized from your computer . Windows Users Make sure that the CRW8824IX is recognized by the operating system.
Setup Procedures 17 Macintosh Users On how to verify the CR W8824IX installation in your CD writing software, r efer to documentation that came with it. n Y our CD writing software will show a device name, Y AMAHA CR W8824E, which corresponds to the CR W8824IX drive (product name).
18 Operations Front Panel Manual Eject hole Only use this if no other method is available for unloading a disc. (P . 21) Disc tray The tray is used to hold the disc.
Operations Rear Panel AC I N SER. NO . st2 ❋❋❋❋❋❋❋❋ IEEE1 39 4 LINE OUT RL Serial number sticker (P . 9) AC IN socket Connect the supplied power cable here. (P . 10) LINE OUT (L/R) Analog line level audio outputs. Connect an external audio device such as powered speakers here.
Operations Loading a Disc 12 1 Open the tray by pressing the Eject button on the CRW8824IX drive’ s front panel. 2 Place the disc onto the tray with its label or printing facing upward. 3 Press the Eject button to close the tray . n When a disc is loaded, the ON/DISC LED is lit up in orange first, then changes to green.
Operations 21 Manually Ejecting a Disc in an Emergency If the disc tray fails to open for some r eason, such as malfunction of the internal spring-loaded mechanism or power outage, it can be opened manually . Y ou should only attempt to eject a disc manually as a last r esort.
22 T roubleshooting Y ou may encounter troubles while using the CR W8824IX drive. This section gives symptoms and possible solutions or step-by-step pr ocedures to walk around. Also r efer to the Y AMAHA CD-R/R W Drives web sites for more information.
T roubleshooting Pressing the Eject button does not open the disc tray . ● Is the CR W8824IX drive powered up? If not, go to the previous symptom, “The drive does not power up” (P . 22). ● Are you using the CD writing softwar e? If so, your CD writing softwar e may lock the tray once the disc is loaded.
T roubleshooting 24 ● Does the drive accept other disc (audio CD, CD-ROM, blank CD-R disc and so on)? When the drive does not accept a specific disc, the disc has a pr oblem such as scratches on its surface, warping or other r easons. The drive may also fail to load even a supported disc if the disc is written impr operly .
T roubleshooting The “Buffer Underrun” error message is displayed. ● T ry the following: • Lower the writing speed setting. • Cr eate an image file of the CD on the computer's hard drive. • Defragment the hard drive. • Close other applications such as scr eensaver , task scheduler , and so on.
26 Appendix Writing Modes Disc-at-Once (DAO) This mode is used when writing a complete disc in a single pass without pausing. Data cannot be added later , even if the full capacity of the blank disc has not been used.
Appendix Session-at-Once (SAO) As a writing method that combines the advantages of the above-mentioned “Disc- at-Once” and “T rack-at-Once,” you can combine multiple tracks into one session and write them, and then add additional data. For example, this is the writing method used to cr eate a CD EXTRA format CD.
Appendix About the Firmware Firmware is a small piece of softwar e built into the CR W8824IX drive, and is used to control the drive’ s basic operations. Since it resides in flash memory , it can be overwritten and updated. T o ensure more r eliable operations and enhanced performance of the drive, updates to the firmware will be made available.
Appendix LED Indicator Messages Status ON/DISC LED READ/WRITE LED P ower on (reset) Ready (no disc) Loading disc Ejecting disc Ready (disc loaded) Seeking Preparing to write Writing Writing (test mode.
Appendix CRW8824IX Specifications Supported Formats CD-DA CD-G CD TEXT CD-ROM (*1) Mixed Mode CD-R OM (CD-ROM+CD-D A) CD-ROM XA (*1) Photo CD (*1) Video CD CD-i CD EXTRA (*2) (*3) (*4) (*4) (*4) (*4) .
Appendix Burst T ransfer Rate 13.3 MB/sec (max) (asynchronous) Data Buffer Size 4MB (1,332 sectors) A verage Random Access Time 140 msec (reading) Sector Size 2,048 ~ 2,352 B Installing Style Horizont.
Appendix Index Symbols 1394 bus controller ............................. 16 4-pin IEEE1394 connector .................. 13 6-pin IEEE1394 cennector .................. 13 A AC IN socket ...................................... 19 Apple System Profiler ..
.
EUROPE, EASTERN EUROPE and RUSSIA Y amaha EUROP A GmbH Y amaha Systems T echnology EUROPE Siemensstrasse 22-34, D-25462 Rellingen, GERMANY F AX: +3214400794 URL: http://www .
XY851A0 Y AMAHA CORPORA TION Printed in Malaysia OW NER’S MA NUAL BEDIENUNGSANLEITUNG MODE D’EMPLOI MANUAL DE INSTRUCCIONES C D - R/RW Drive C R W 8824I X SERIES C R W 8824I X SERIES OW NER’S MA.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Yamaha CRW8824IX Series è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Yamaha CRW8824IX Series - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Yamaha CRW8824IX Series imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Yamaha CRW8824IX Series ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Yamaha CRW8824IX Series, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Yamaha CRW8824IX Series.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Yamaha CRW8824IX Series. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Yamaha CRW8824IX Series insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
