Manuale d’uso / di manutenzione del prodotto WATL27105.1 del fabbricante Weslo
Vai alla pagina of 23
Model No. W A TL27105.1 Serial No. Write the serial number in the space above for future reference. CAUTION Read all precautions and instruc- tions in this manual before using this equipment.
2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 1. It is the responsibility of the owner to ensure t hat all users of this treadmill are adequately informed of all warnings and precautions. 2. Use the treadmill only as described. 3. Place the treadmill on a level surface, with at least 2.5 m (8 ft.
4 2 3. DANGER: A lways unplug the power cord immediately after use, before cleaning the treadmill, and before performing the m aintenance and adjustment procedures described in this manual. Never remove the motor hood unless instructed to do so by an authorized service representative.
5 BEFORE YOU BEGIN Thank you for selecting the new WESLO ® E-20 tread- mill. The E-20 treadmill of fers an impressive array of features designed to help you achieve your fitness g oals in the convenience and privacy o f yo ur ho me.
6 ASSEMBL Y Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not d ispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant.
7 3. Hold a Frame Spacer (27) against the right side of the F rame (79) as shown. Insert a 4” Bolt (70) into the indi- cated hole in the Frame Spacer and the Frame. Next, tighten a 3/4” T ek Screw (3) into the Frame Spacer and the Frame. Then, remove the Bolt.
8 6 . Carefully pull the opposite end of the tape to pull the W ire Harness (60) up through the Right Handrail (59) and out of the hole in the side of the Right Handrail. Remove the tape from the Wire Harness (60). 59 T ape 6 0 6 7. Orient the Crossbar (91) with the large hole at the right of the smaller hole as shown.
9 12. Make sure that all parts used in assembly are properly tightened before you use the treadmill. Keep the included hex key in a secure place; the hex key is used to adjust the walking belt (see page 18). T o pro- tect the floor or carpet, place a mat under the treadmill.
10 OPERA TION AND ADJUSTMENT THE PRE-LUBRICA TED WALKING BEL T Y our treadmill features a walking belt coated with high-performance lubricant. IMPORT ANT : Never apply sili- cone spray or other substances to the walking belt or the walking platform. Such substances will deteri- o rate the walking belt and cause excessive wear .
1 1 FEA TURES OF THE CONSOLE The treadmill console offers a selection of features designed to make your workouts more effective. When the manual mode of the console is selected, the speed and incline of the treadmill can be changed with the t ouch of a button.
12 Insert the key into the console. See HOW T O TURN ON THE POWER on page 1 1. Select the manual mode. When the key is insert- e d, the manual mode will be selected; three zeros will appear in the T ime/Pace zone of the display . If a pro- gram has been selected, remove the key and then reinsert it to select the manual mode.
13 The T ime/Pace zone of the display will show t he total number of hours that the treadmill h as been used. The Distance zone of the display will show the total number of miles that the walking belt has moved. IMPORT ANT : If a “d” appears in the Speed zone of the display , the console is in the “demo” mode.
14 Press the Start button or the Speed increase button to start the prog ram. A moment after the button is pressed, the tread- mill will automatically adjust to the first speed set- t ing fo r the progr am. Hold the handrails and begin walking. Each program is divided into 30 one-minute peri- ods.
15 HOW T O FOLD AND MOVE THE TREADMILL HOW TO FOLD THE TREADMILL FOR ST ORAGE Before folding the treadmill, unplug the power cord. CAUTION: Y ou must be able to safely lift 45 pounds (20 k g) to raise, lower or move the treadmill. 1. Hold the treadmill with your hands in the location shown by the arrow at the right.
16 HOW TO LOWER THE TREADMILL FOR USE 1. Hold the upper end of the treadmill with your right hand as shown. Using your left hand, pull the lock knob to the left and hold it. Pivot the frame down until it is past the lock pin. Slowly release the lock knob.
17 TROUBLESHOOTING Most treadmill problems can be solved by following the steps below . Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on SOLUTION: a.
18 PROBLEM: The walking belt slows when walked on S OLUTION: a . If an extension cord is needed, use only a 3-conductor , 1mm 2 ( 14-gauge) cord that is no longer than 1.5 m (5 ft.). b. If the walking belt is overtightened, treadmill perfor- mance may decrease and the walking belt may become damaged.
19 CONDITIONING GUIDELINES The following guidelines will help you to plan your exercise program. For more detailed exercise informa- tion, obtain a reputable book or consult your physi- cian.
Handrail Bolt (20)–4 F rame Bolt (32)–2 3/8” W asher (66)–2 W Silver Ground Screw (69)–1 3/8” Star W asher (29)–2 2” Bolt (62)–4 2 1/2” Bolt (65)–4 3/8” Nut (13)–4 5/16” Nu.
P ART LIST—Model No. W A TL27105.1 R1 105A 1 1 Motor Hood 2 14 3/4” Screw 3 18 3/4” T ek Screw 4 5 8” Cable T ie 5 4 1” T ek Screw 6 1 W arning Decal, Console 7 3 Cable T ie Clamp 8 2 Foot R.
61 13 21 21 32 7 4 96 96 22 24 25 26 19 56 76 27 3 47 16 3 10 3 18 51 3 18 39 27 3 8 10 3 3 79 14 73 77 74 72 87 15 80 82 81 83 43 82 81 85 49 43 64 87 80 14 15 8 1 3 3 12 12 41 40 40 62 68 13 63 5 2 .
Part No. 232938 R1 105A Printed in Canada © 2005 ICON IP , Inc. LIMITED W ARRANTY Shanghai Newlife Fitness Equipment, Inc. (Newlife), warrants this product to be free from defects in work - manship and material under normal use and service conditions.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Weslo WATL27105.1 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Weslo WATL27105.1 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Weslo WATL27105.1 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Weslo WATL27105.1 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Weslo WATL27105.1, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Weslo WATL27105.1.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Weslo WATL27105.1. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Weslo WATL27105.1 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
