Manuale d’uso / di manutenzione del prodotto 292003 del fabbricante Wagner SprayTech
Vai alla pagina of 20
1 OWNER'S MANUAL Read Rules for Safe Operation and Instructions Carefully Fine Finish ST A TI-KIT CAUTION T.M. VM200 HV I O T0.2A VM200 H V I O T 0 .
1 CONTENTS SAFETY PRECAUTIONS .................................................................... 3-6 SPECIFICA TIONS ................................................................................ 7 INTRODUCTIONS ...................................
1 SAFETY PRECAUTIONS This manual contains information which must be read and understood before using the equipment. When you come to an area which has one of the following symbols, pay particular attention and make certain to heed the safeguard. Important safety information indicates a hazard which may cause serious injury or loss of life.
1 HAZARD WARNING Electrostatic arcing may cause an explosion or fire. Solvent and paint fumes can explode or ignite causing property damage and/or severe injury. PREVENTION • Operator must be grounded. Grounding straps must be used when wearing rubber soled shoes.
1 HAZARD WARNING • Follow the requirements of the Material Safety Data Sheet supplied by the coatings manufacturer. • Exhaust and fresh air introduction must be provided within the spray area to keep the air free of accumula- tions of toxic materials.
1 WARNING PREVENTION HAZARD General • All accessories must be rated at or above the maximum pressure rating of spray pump (includes spray tips, guns, extensions and fluid hose. • If you are injected, see a physician immediately. Injection (Con't) DO NOT TREAT AS A SIMPLE CUT! It can lead to amputation.
1 SPECIFICA TIONS GM2000 EAC SPRA YGUN (P/N 0179673) Air Pressure, max. 145 psi Material Pressure, max. 3625 psi Air Volume 10 CFM@ 45 PSI Material Volume Varies due to Tip size Air Connector 1/4 inch Material Connector NPS 1/4 Length 11.8 inches Height 10 inches Weight 21 oz.
1 Figure 1 Figure 2 HV GM 2000 O I T0.2A VM200 GROUND CONNECTION FUSE ON - OFF SWITCH RED HIGH VOLTAGE LAMP HIGH VOLTAGE CABLE SOCKET GENERAL DESCRIPTION GM2000 EAC SPRA Y GUN The GM2000 EAC Electrostatic Air Coat Spraygun is very light and easy to service.
1 TYPICAL MOUNTING AR- RANGEMENT W AGNER AIRLESS SPRA YER MOUNTING INSTRUCTIONS 1. Use the allen wrench provided, attach the mounting bracket (1) to the power pack (2) with the 2.4mm lockwashers (3) and socket head screws (4). 2. Place the power pack/mounting bracket assembly on any 1" diameter tube, preferably as illustrated below.
1 Power cord ground must remain intact. Do not clip off ground pole on plug to fit a non- grounded socket. Static build up will result which may cause an explosion. WARNING Figure 4 SET -UP SET -UP VM 200 POWER PACK: 1. GM 2000 EAC Socket Outlet 2. Ground Connection Knob 3.
1 CLEAN UP WHEN CLEANING THE ELECTROST A TIC SYSTEM, THESE SAFETY PROCEDURES MUST BE FOLLOWED. FAILURE T O FOL- LOW THESE PROCEDURES MA Y RESUL T IN AN EXPLOSION/FIRE. • Turn power pack to the “OFF” position and unplug from power source before starting to clean.
1 TIP CHANGE CHANGING THE ROUND SPRA Y TIP 1. Screw out spray tip (B) with tip wrench (A). (See Fig.5) 2. Attach desired spray tip and tighten with tip wrench. CLEANING OF THE FLA T SPRA Y TIP • Remove air cap (H). (See Fig. 8) • Remove flat spray tip (G) and clean it.
1 VA L VE SEAL REPLACEMENT To replace valve seals you must remove the entire valve rod. 1. Actuate trigger (3) and unscrew trigger lock knob (2), remove the compression spring. Fig. 11 2. Remove screws holding trigger asembly in place and remove trigger (3).
1 14 Problem • No green light on Power Pack • Gun on-off switch performing opposite. • No red light on Power Pack. • Spray pattern not even; unsymmetrical or poor atomization. • Spray pattern is correct, but there is no wraparound. • Dead outlet.
1 TROUBLESHOOTING Problem • Air leaking at tip without pulling trigger. • Air leaks between gun body and gun barrel. • No air at tip when trigger is pulled. • Air valve is faulty. • Gun Barrel Nut. • Air hose not connected. • No air supply • Wrong tip body fitted • Round tip nut screwed down too hard.
1 Figure 9 16.
1 GM 2000 EAC Item Description Part Number 1 Spray gun barrel 0179500 2 Bushing 0128336 3 Screw countersunk 0179354 4 Type plate 9900962 5 Screw flathead 9900810 6 O-ring 9971003 7 Knob, Air Adjustmen.
1 Flat T ip Part Tip Orifice Size Fan Number Marking (Inch) Width 0128550 9/15 .009 15 ° 0128216 9/20 .009 20 ° 0128552 11/15 .011 15 ° 0128217 11/20 .011 20 ° 0128201 11/50 .011 50 ° 0128554 13/15 .013 15 ° 0128218 13/20 .013 20 ° 0128212 13/50 .
19.
LIMITED W ARRANTY ELECTROST A TIC P AINT SPRA Y EQUIPMENT To validate this warranty, the completed registration card must be mailed within one week of the date of purchase to Wagner Spray Tech Corporation.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Wagner SprayTech 292003 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Wagner SprayTech 292003 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Wagner SprayTech 292003 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Wagner SprayTech 292003 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Wagner SprayTech 292003, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Wagner SprayTech 292003.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Wagner SprayTech 292003. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Wagner SprayTech 292003 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
