Manuale d’uso / di manutenzione del prodotto AF-24 del fabbricante Ubiquiti Networks
Vai alla pagina of 36
24 GHz Point to Point 1.4+ Gbps Radio Model: AF-24.
.
Introduction Thank you f or purchasing the Ubiquiti Networks® airF iber® 24GHz Point-t o-Point Radio . This Quick Start Guide is designed to guide you through installation, show y ou how to access the airF iber Configuration Interface, and explain how t o set up an airF iber link.
Hardware Overview Side Alignment Bracket Elevation Adjustment Azimuth Adjustment Ground Bonding Point Lock Bolts Lock Bolts 2 airFiber® AF-24 Quick Start Guide.
Back Lock Bolts Lock Bolts Azimuth Adjustment Lock Bolts Lock Bolts Cover L ock Elevation Adjustment Port Cover 3 Hardware Overview.
Inter faces RESET D ATA AUX CONFIG LED Display Interface Description RESET T o reset to factory defaults, press and hold the Reset button for more than fiv e seconds while the unit is already powered on. D ATA 10/100/1000 Mbps port handles all user traffic.
LED Stat e Status D ATA Speed Off 10/100 Mbps On 1000 Mbps Link/Act Off No Ethernet Link On Ethernet Link Established Random Flashing Ethernet Activity AUX GPS Off No GPS Synchronization On Operationa.
Installation Requirements • 17 mm wrench • 13 mm socket wrench or driver • Clear line of sight between airF iber radios • Clear view of the sky for proper GPS operation • Mounting location with < 0.
• Once configuration is complet e, disconnect the cables to mov e the airFiber r adios. • Reconnect at the site. • After you hav e mounted the airFiber radios , establish and optimize the RF link. Connecting P ower over E thernet 1. T urn the Cover Lock t o the Unlocked icon.
3. Connect the other end of the Ethernet cable from the D ATA port to the Ethernet por t labeled POE on the GigE PoE Adapter . 4. Connect the Power C ord to the power por t on the GigE PoE Adapter . Connect the other end of the Power Cord to a po wer source.
airF iber Configuration The instructions in this section explain how to access the airFiber Configuration Interface and configure the follo wing settings: • Wireless Mode Configure one airF iber AF-24 as the Master and the other as the Slave . • Duplex The airFiber AF-24 supports both half-duplex and full-duplex operation.
1. Connect an Ethernet cable from your comput er to the CONFIG port on the airFiber AF-24. 2. Configure the Ethernet adapt er on your computer with a static IP address on the 192.168.1.x subnet (for example , 192.168.1.100). 3. Launch your web bro wser .
5. Click the Wireless tab . 6. Enter the Basic Wireless Settings : a. For one airF iber AF-24, selec t Master from the Wireless Mode drop-down. F or the other airFiber AF-24, keep the default, Slave . b. Enter a name in the Link Name field. This should be the same on both the Master and the Slave .
7. Configure the Wireless Security : a. Selec t the AES Key T ype , HEX or ASCII . b. For the Key field: - HEX Enter 16 bytes (eight, 16-bit HEX values: 0-9, A-F , or a-f ).
Hardware Installation T o install the airF iber AF-24: 1. Insert the four Carriage Bolts into the Pole Mount Br acket . 2. Attach the P ole Mount Brack et to a pole. Note: The mounting assembly can accommodate a Ø 51 - 101 mm (2.0" - 4.0") pole.
3. Loosen, but do NO T remove the eight Lock Bolts located on the Alignment Brack et . 4. Ensure that there is a 6 mm gap between the head of each M8x14 Serrated Flange Screw and the Alignment Br acket .
5. Lift the airFiber AF-24 and align the f our M8x14 Serrated Flange Screws with the slots on the Pole Mount Br acket. Seat the screws in the slots. Securely tighten the screws . W ARNING: T o prevent injury , ensure that all four screws are seated and fully tightened .
6. Attach a ground wire: a. Remove the nut from the Ground Bonding Point . b. Attach a ground wire (min. 8 A WG or 10 mm 2 ) to the lug and replace the nut to secure the wire . c. Secure the other end of the ground wire to a grounded mast, pole, t ower , or grounding bar .
Connecting Ethernet 1. T urn the Cover Lock t o the Unlocked icon. Slide the Port Cov er down to remov e it. 2. Connect a TOUGHC able or other outdoor , shielded CA T5e/6 cable to the DA T A port. 3. Create a strain relief f or the Ethernet cable by feeding a Cable Tie through the tie slot under the cable.
4. Connect the other end of the Ethernet cable from the D ATA port to the Ethernet por t labeled POE on the GigE PoE Adapter . 5. Connect an Ethernet cable from your netw ork to the Ethernet port labeled L AN on the GigE PoE A dapter. 6. Connect the Power C ord to the power por t on the GigE PoE Adapter .
Below is a diagram of a finished installation with recommended surge protectors installed . Ground to Pole, T ower, or Grounding Block (Max. 1 m from Ground Bonding Point) Max.
Alignment Tips • Fine-tuning is best achiev ed by a pair of installers with a dedicated , two-way communication link: one installer makes adjustments on one airFiber r adio while the other installer reports the received signal level at the other airF iber radio.
2. F or the Master and Slave , ensure the A zimuth (AZ) and Elevation (EL) Adjustment Bolts ar e in the middle of their adjustmentranges. Elevation (EL) Adjustment Bolt Azimuth (AZ) Adjustment Bolt 3. Master Aim the Master at the Slave . If necessary , adjust the Master 's position on the pole: a.
5. Master Adjust the azimuth and elevation of the Master until the strongest received signal lev el is displayed on the LED Display of the Master . a. Sweep the Azimuth (AZ) Adjustment Bolt of the Master through its adjustment range. Master Azimuth (AZ) Adjustment Bolt b.
F ine-T uning the Link The Azimuth (AZ) and Elevation (EL) Adjustment Bolts of the Alignment Brack et adjust the azimuth and elevation within a range of ±10°. F or accurate alignment, make adjustments on one end of the link while the other installer reports the received signal level at the other end of the link.
There are three methods f or determining the received signal level: • LED Display (described abov e) • airF iber Configuration Interface • Audio tone (optional equipment requir ed) Refer to the airF iber AF-24 User Guide for instructions on the airFiber C onfiguration Inter face and audio tone methods.
Specifications airFiber AF-24 Dimensions 649 x 426 x 303 mm (25.55 x 16.77 x 11.93") W eight 10.5 kg (23.15 lb) Mount Included Operating F requency 24.
Electrical Safety Information 1. Compliance is required with r espect to voltage, frequency , and current requirements indicated on the manufacturer’ s label. Connection to a different pow er source than those specified may result in impr oper operation, damage to the equipment or pose a fire hazard if the limitations are not follow ed.
W arranty Conditions The above warr ant y does not apply if the Product: (I) has been modified and/or altered , or an addition made thereto, except by Ubiquiti Netw orks, or Ubiquiti Networks’ autho.
Disclaimer EX CEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NET WORKS, ITS AFFILIA TES, AND ITS AND THEIR THIRD P ART Y DA T A, SERVICE, SOFT W ARE AND HARDWARE PROVIDERS HEREBY DISCLAIM A.
Note Some countries, states and pr ovinces do not allow ex clusions of implied warranties or conditions, so the abo ve exclusion may not apply to you . Y ou may ha ve other rights that vary from countr y to country , state to state, or pro vince to province.
Industr y Canada CAN ICES-3(A)/NMB-3(A) This Class A digital apparatus complies with Canadian CAN ICES-3(A). T o reduce potential radio interference to other users , the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e .
CE Mark ing CE marking on this product represents the product is in compliance with all directives that are applicable to it. This equipment is intended t o be accessed only by service personnel and/or trained professionals.
PHRRJL090514 Magyar [Hungarian] Alulírott, UBIQUITI NET WORKS nyilatkozom, hogy a UBIQUITI NET WORKS device, megfelel a vonatkoz ó alapvetõ követelmén yeknek és az 1999/5/EC irányelv egyéb elõírásainak.
.
© 2012-2014 Ubiquiti Networks, Inc. All rights reserved . Ubiquiti, UbiquitiNetworks, the Ubiquiti U logo, the Ubiquiti beam logo , airFiber , EdgeRouter, and T OUGHCable are trademarks or registered trademarks of UbiquitiNetworks ,Inc . in the United States and inother countries.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Ubiquiti Networks AF-24 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Ubiquiti Networks AF-24 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Ubiquiti Networks AF-24 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Ubiquiti Networks AF-24 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Ubiquiti Networks AF-24, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Ubiquiti Networks AF-24.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Ubiquiti Networks AF-24. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Ubiquiti Networks AF-24 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
