Manuale d’uso / di manutenzione del prodotto 12180 del fabbricante Troy-Bilt
Vai alla pagina of 28
Model 12180 Owner’ s Manual BRONCO TM 5 HP Model T iller • Safety • Assembly • Controls • Operation • Maintenance B R O N C O GARDEN WAY INCORPORATED.
2 T able of Contents SECTION 1: SAFETY ........................................... 3 Safety Decals .................................................................... 5 SECTION 2: ASSEMBLY ....................................... 6 Attach Handlebar ..
3 T raining 1. Carefully read this Owner ’ s Manual, the separate Engine Owner ’ s Manual, and any other literature you may receive. Be thoroughly familiar with the controls and the proper use of the tiller and its engine. Know how to stop the unit and disengage the controls quickly.
7. Take all possible precautions when leaving the machine unattended. Stop the engine. Disconnect spark plug wire and move it away from the spark plug. Be sure both wheels are in the Wheel Drive position. 8. Before cleaning, repairing, or inspect- ing, stop the engine and make certain all moving parts have stopped.
Section 1: Safety 5 Decals For your safety and the safety of others, various safety and operational decals are located on your unit (see Figure 1 below). Keep the decals clean and legible at all times. Contact your local service dealer or the factory for replacements if any decals are damaged or missing.
6 WARNING T o prevent personal injur y or property damage, do not start the engine until all assembly steps are complete and you have read and understand the safety and operating instruc- tions in this manual. Introduction Carefully follow these assembly steps to correctly prepare your tiller for use.
7 Section 2: Assembly STEP 2: Attach Handlebar 1. Attach the two legs of the handlebar support (A, Fig. 2-2) loosely to the inner sides of the tiller frame using two 3/8"-16 x 3/4" hex hd. screws (B), 3/8" flat washers (C) and 3/8"-16 hex locknuts (D).
8 Section 2: Assembly STEP 4: Install Forward Clutch Cable 1. Place the forward clutch cable bracket (P, Fig. 2-4) on the handlebar support (A). Attach the cable bracket using a 1/4"-20 x 1-1/4" hex hd. screw (R, Fig. 2-4) and 1/4"-20 hex locknut (S).
9 Section 2: Assembly Fig. 2-8: Install reverse cable bracket and reverse clutch cable. STEP 5: Install Reverse Clutch Cable 1. Remove the two pre-installed self- tapping screws (AA, Fig. 2-8) from the handlebars. Position the reverse cable mounting bracket (BB, Fig.
Wheel Drive Pins Each wheel is equipped with a Wheel Drive Pin (A, Figures 3-2 and 3-3) that secures the wheel to the wheel shaft (B). The wheels can be positioned in either a WHEEL DRIVE or a FREEWHEEL mode.
11 Section 3: Features and Controls 4. FOR WHEEL DRIVE mode (Figure 3-2): Slide the wheel outward and align the holes in the wheel hub (D, Figure 3-2)) and the wheel shaft (B).
12 Section 3: Features and Controls Depth Regulator Lever This lever (G, Figure 3-5) controls the tilling depth of the tines. Pull the lever straight back and slide it up or down to engage the notched height settings. The highest notch (lever all the way down) raises the tines approximately 1-1/2" off the ground.
13 Figure 4-1 Section 4 Operation WARNING Before operating your machine, carefully read and understand all safety (Section 1), controls (Section 3) and operating instructions (Section 4) in this Manual, in the separate Engine Owner ’ s Manual, and on the decals on the machine.
14 Starting the Engine The following steps describe how to start and stop the engine. Do not attempt to engage the tines or wheels until you have read all of the operating instruc- tions in this Section. Also review the safety rules in Section 1: “ Safety ” and the tiller and engine controls information in Section 3: “ Features and Controls.
15 Section 4: Operation 5. For reverse motion of the wheels and tines: (a) Look behind and exercise caution when operating in reverse. Do not till while in reverse.
16 Section 4: Operation T illing T ips & T echniques Let the tiller do the work • While tilling, relax and let the wheels pull the tiller along while the tines do the digging. Walk on the side that is not yet finished (to avoid making foot- prints in the freshly tilled soil) and lightly, but securely grip the handlebar with just one hand.
17 Section 4: Operation T illing T ips & T echniques Clearing the tines The tines have a self-clearing action which eliminates most tangling of debris in the tines. However, occasionally dry grass, stringy stalks or tough vines may become tangled.
18 Section 4: Operation POWER COMPOSTING Power composting simply means tilling under and burying in the soil all manner of organic matter such as crop residues, leaves, grass clippings and cover crops. This material will decompose during the non-growing season and add important natural nutrients to the soil.
19 Section 5 Maintenance REQUIRED MAINTENANCE SCHEDULE Before Every Every As PROCEDURE Each 10 30 Noted Use Hours Hours Check engine oil level • And every 5 operating hours Clean engine • ▲ Chec.
20 Section 5: Maintenance TILLER LUBRICA TION Proper lubrication of the tiller is an essential part of your maintenance program. After every 10 operating hours, oil or grease the lubrication points shown in Figure 5-1 and described below.
Section 5: Maintenance B. To Drain the Transmission Gear Oil: The transmission gear oil does not need to be changed unless it has been contam- inated with dirt, sand or metal particles. 1. Drain gasoline from the fuel tank or run the engine until the fuel tank is empty.
CHECKING AND ADJUSTING FORWARD DRIVE BEL T TENSION Maintaining correct tension on the forward drive belt is important to good tilling performance and long belt life. A loose belt will slip on the engine and transmission pulleys and cause the tines and wheels to slow down – or stop com- pletely – even though the engine is running at full speed.
Section 5: Maintenance W ARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage.
24 Section 5: Maintenance W ARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property damage.
25 Section 5: Maintenance TROUBLESHOOTING Before performing any corrections, refer to the appropriate information in this Manual, or in the Engine Owner ’ s Manual, for the correct safety precautions and operating or maintenance procedures. Contact your local authorized Engine Service Dealer for engine service.
26 TILLER SPECIFICA TIONS/A TT ACHMENTS TILLER SPECIFICA TIONS TILLER HEIGHT (with Depth Regulator Lever in highest setting): Without Handlebars .................................................................................25-1/2" Handlebars in lowest setting.
27 CUSTOMER SERVICE INFORMA TION Owner Registration Card Please fill out and mail the enclosed owner registration card. The purpose of this card is to register each unit at the factory in order to keep the owner informed with informational bulletins and safety literature.
1905362 (3/99) Printed in U.S.A. © 1999 Garden Way Incorporated.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Troy-Bilt 12180 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Troy-Bilt 12180 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Troy-Bilt 12180 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Troy-Bilt 12180 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Troy-Bilt 12180, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Troy-Bilt 12180.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Troy-Bilt 12180. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Troy-Bilt 12180 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
