Manuale d’uso / di manutenzione del prodotto NEO-10 del fabbricante Telex
Vai alla pagina of 26
Model NEO-10 Version 1.0 Technical Manual November 26, 2003 PN: 803968.
2 Table of Contents 1 INTRODUCTION................................................................................................................... ........................... 3 2 CONNECTING NE O TO THE WORLD ........................................
3 1 Introduction The NEO-10 device is a network based Input Outpu t device. Within its enclosure are 10 DPDT relays with all 6 contacts of the relays brought out to ports (Normally Open, Norm al ly Close, Common for each half of relay). There are also 10 dio de blocked inp uts which can be used to mo nitor external events.
4 2 Connecting NEO to the World NEO has a total of three different ports th at are used to connect it to the world. Likely, the first port that will need to be connected is th e RS-232 port. 2.1 RS-232 Port The RS-232 port is used for initial setup purpo ses only.
5 3 Sof tware Configuration of NEO Setup of the N EO is almost enti rely done using a web browser. The first step required during setup is to assign the IP and Mask a ddresses to the NEO, using either a WEB Browser or Hyper Te rminal program if the assigned IP address is not accessible on your network.
6 At the main Hyper Term inal screen type up percase S then <enter>. Enter “technobabble” for the factory password..
7 A = The board serial num ber and case serial number s hould match. B = Do you want to reset the PIN number programmed into NEO. C = Current I P address, do yo u want to change ? D = Current Subn et .
8 3.2 General Setup via Web Pages The majority of the setup of the NEO is com pleted through t he Ethernet port. Onc e the steps of 3.1 ha ve been completed, a PC on the network can be used to gain access to the web page based setup of the NEO. In the URL window of Int ernet Explore r, type http://X.
9 Once all parameters are set, press the Submit bu tton to se nd them back to the NEO fr om the web browser. The parameters are not updated until they are actually saved to EPROM, (Section 3.
10 3.4 Multicast Setup A single m ulticast address is em ployed by NEO for t he purpose of upda ting consoles o f changes in the R elays and Inputs. NEO sends out a single packet each time either a Relay is changed by a ny console or when an input changes due to external event.
11 3.5 Debounce Input Settings The Debounce hyperlink will open the screen below. Each of the 10 input s can have its own inp ut debounce time. This is t he amount of tim e, in milliseconds, that the input is allowed to stabilize from first change detectio n to final sampling.
12 3.6 Echo Packet The Echo Packet function allo ws the system to operate on networks that do not support multicast. A typical application might be a number of radios spread throu ghout a network.
13 Figure 7 - Echo Packet Setup.
14 3.7 Clone From Other NEO The Clone func tion allows for t he parameters of one NEO to be copied t o another ove r the network. Sim ply enter the IP address of the unit to co py the parameters from a nd press the submit button . Th e parameters will be copied.
15 3.8 PIN Change The PIN num ber is the passw ord required to enter the set up mode of t he NEO. The default is no PI N number. T he PIN number is a 4 digit num ber that m ust be entered t wice and then s ubmitted.
16 3.9 Save Changes to EEPROM As each group of settings are change d an d submitted, they still must be saved to EEPROM to be stored perm anently. Some settings req uire reboot of the device to ta ke effect.
17 4 BILL OF MA TERIAL AND SCHEMA TICS.
REVISIONS RE V DESCRIPTION ECO NO DATE A PPD 1 PROTOTYPE 09/16/03 This drawing, written description or specification Is a proprietary product of TELEX, Lincoln, NE, and shall not be released, disclosed, nor duplicated without the written permission of TELEX.
ITEM NEW QTY TYPE DESCRIPTION PART NO. DESIGNATOR 1 14 CAP 10uf 16vTANT 3528 B 102877065T C1 C3 C11 C18 C19 C68 C71 C73 C74 C123 C124 C131 C162 C329 2 15 CAP 0805 0.1UF 25V +/-10% 102881186T C6 C7 C8 C9 C10 C12 C13 C29 C30 C56 C69 C72 C75 C330 C59 3 1 CAP 1000U,ELECTROLYTIC,LEADED D O NOT PLACE C15 4 1 CAP .
ITEM NEW QTY TYPE DESCRIPTION PART NO. DESIGNATOR This drawin g , written description or specification Is a proprietary product of TELEX, Lincoln, NE, and shall not be released, disclosed, nor duplicated without the written permission of TELEX. Telex Communications INC.
ITEM NEW QTY TYPE DESCRIPTION PART NO. DESIGNATOR This drawin g , written description or specification Is a proprietary product of TELEX, Lincoln, NE, and shall not be released, disclosed, nor duplicated without the written permission of TELEX. Telex Communications INC.
.
.
.
.
18 5 W arranty , Service, Rep air , and Comment s Important! Be sure the exact return address and a description of the problem or work to be done are enclosed w ith your equipment.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Telex NEO-10 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Telex NEO-10 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Telex NEO-10 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Telex NEO-10 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Telex NEO-10, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Telex NEO-10.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Telex NEO-10. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Telex NEO-10 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
