Manuale d’uso / di manutenzione del prodotto CT04 del fabbricante Stanley Black & Decker
Vai alla pagina of 20
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 58541 10-2014 V er . 4 USER MANUAL Safety , Operation and Maintenance CT04 HYDRAULIC CRIMPING T OOL.
.
CT04 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer .
4 ► CT04 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
CT04 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs.
6 ► CT04 User Manual SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL.
CT04 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
8 ► CT04 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
CT04 User Manual ◄ 9 HTMA / EHTMA REQUIREMENTS Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min.
10 ► CT04 User Manual 2. Loosen the 2 setscrews on the cylinder . 3. Turn the adapter until it stops: • Counter Clockwise (CCW) to change to closed center (creates gap) • Clockwise (CW) to change to open center (clos - es gap) 4. Tighten the two setscrews.
CT04 User Manual ◄ 1 1 • If the die load has been veried, select a set of dies to match the sleeve or connector to be crimped. TO INST ALL DIES ON KEARNEY “O” STYLE HEAD 1. Loosen the two die retainer screws (items ___ on the parts illustration).
12 ► CT04 User Manual The hydraulic uid temperature should be at least 80 °F/27 °C for this test. CONNECT HOSES 1. Wipe all hose couplers with a clean, lint-free cloth before making connections. 2. Connect hoses from the hydraulic power source to the tool ttings or quick disconnects.
CT04 User Manual ◄ 13 SHUTDOWN 1. Move the hydraulic system control valve to the OFF position. 2. Disconnect the hydraulic hoses from the tool - rst the input (supply) hose, then the output (return) hose. 3. Insert plugs in the hose ends, couplers or tool ports, as applicable.
14 ► CT04 User Manual NO TICE In addition to the Safety Precautions found in this manual, observe the following for equipment protection and care. • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau - lic tools.
CT04 User Manual ◄ 15 If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the grinder , always check that the hydraulic power source is supplying the correct hydraulic ow and pressure to the grinder as listed in the table.
16 ► CT04 User Manual Capacity ........................................................................................................................................ #6 - 4/0 Conductor Crimping Force ...............................................
CT04 User Manual ◄ 17 CT04 ILLUSTRA TION.
18 ► CT04 User Manual ITEM NO. P ART NO. QTY DESCRIPTION 1 001 18 1 RET AINING RING 2 00144 12 HSHCS 3 07626 2 O-RING ■ 4 09330 1 O-RING ■ 5 00294 1 O-RING ■ 6 00360 1 O-RING ■ 7 00831 1 ROD.
.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 503-659-5660 / Fax 503-652-1780 www .stanleyhydraulics.com.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Stanley Black & Decker CT04 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Stanley Black & Decker CT04 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Stanley Black & Decker CT04 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Stanley Black & Decker CT04 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Stanley Black & Decker CT04, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Stanley Black & Decker CT04.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Stanley Black & Decker CT04. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Stanley Black & Decker CT04 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
