Manuale d’uso / di manutenzione del prodotto s1-2k del fabbricante Silicon Image
Vai alla pagina of 38
© 2008 Sil icon Imagin g, Inc P age 1 SI-2K Image & Softwa re Install Manual SiliconDVR Version 1.1 December 2008 Part #25436.
© 2008 Sil icon Imagin g, Inc P age 2 Table of Contents Section Page 1.0 - Introduction 3 1.1 Release Notes for SiliconDVR Ve rsion 1.1 3 2.0 SI-2K Maintenance T ool (SI-2K Recorder Use) 6 2.1 Downl oad and Pre-installati on 6 2.11 Dow nloading 4 2.12 Prepare the US B Drive 5 2.
© 2008 Sil icon Imagin g, Inc P age 3 1.0 Introduction This m anual covers the installatio n and update procedure for the following : • SI-2K Recorders using Maintenance Tool (Section 2) • PC/Lap.
© 2008 Sil icon Imagin g, Inc P age 4 1.1 Release Notes for SiliconDVR Ve rsion 1.1 Image Quality - Improved re li abil i ty in bl ack cali brati on - Enhanced devian t pixel detection processes - Increase d total count of Deviant pi xels detected and correcte d - Reduced column FPN i n hi gh-temp - Higher Qual ity Ci neform Encoder Mo des (3.
© 2008 Sil icon Imagin g, Inc P age 5 SI-2K & Windows-XP Embedded Support tools - USB thumb -drive SI-2K Image Install er (Maintenan ce Too l) - New XP-e Write Fil ter (FBFW) used to prevent data writi ng to the compact flash card whi ch contains th e OS Image.
© 2008 Sil icon Imagin g, Inc P age 6 2.0 SI-2K M aintenance Tool ( For SI-2K Recorders Only ) The SI-2K contains a compact fl ash memory card that appears as the “C:” drive when the system is operating. The system boots and runs the Sil iconDVR appli cati on from this drive.
© 2008 Sil icon Imagin g, Inc P age 7 2.1 Dow nload and Pre-installati on If you have re ceived the SI-2K Main tenance Tool already inst all ed on a USB drive, you may skip to the section “ 2.2 Before You Boot ” 2.1.1 Downloa ding The SI-2K Maint enance Tool is di stributed i n a sin gle ZIP file th at may be more than 1GB in si ze.
© 2008 Sil icon Imagin g, Inc P age 8 A warning message will appear as shown in Figu re 2. Ve rify that th e flash dri ve has been correc tly i denti fied, i n thi s example it’s dri ve “F:”, and press ENTE R to make the drive bootable.
© 2008 Sil icon Imagin g, Inc P age 9 2.2 Before You Boot The Maintena nce Tool is design ed to modify only th e internal fl ash drive, but i t’s alwa ys prudent to make sure that any work you have on the SI -2K has been copied off the system prior to using the tool .
© 2008 Sil icon Imagin g, Inc P age 10 2.3 Using the Mai ntenance Tool The Maintena nce Tool interface is operated using the mouse on the side of the SI-2K (not via touchscreen). There are two types of flash media used in th e SI-2K, Transcend and X4.
© 2008 Sil icon Imagin g, Inc P age 11 Once the restor e operation has completed, whi ch typical l y takes five to ten minutes, you wil l see a message repor tin g OPERATION IS FINISHED .
© 2008 Sil icon Imagin g, Inc P age 12 2.4 Troubleshooting 2.4.1 BIO S SETTINGS IF BOO T FA ILS If the SI-2K does not boo t in to the Maint enance tool, the BIOS boot se ttin gs may need to be adjusted. 1. Connect a USB Keyboard and a moni tor to the VGA por t (do not use the SI-2K Electronic Viewfi nder) to the switched off camera.
© 2008 Sil icon Imagin g, Inc P age 13 2.5 Touchscreen Calibration & Drivers The flash drive of the SI-2K i s protected fro m ina dvertent writing by the Fil e Based Write Fil ter (FBWF). Thi s protection keeps the file system from being corrupted during u nexpected shutdowns, such as when the bat tery runs down.
© 2008 Sil icon Imagin g, Inc P age 14 3.0 Sil iconDVR Installer ( For PC/Laptop Only ) The instal la tion i nstructi ons for install i ng Si li conDVR are spli t int o two sets: One fo r Intel Pro10.
© 2008 Sil icon Imagin g, Inc P age 15 3.2 Instal ling SiliconDVR for Pro1 000 NIC’s: 1. Certify that the Pro1000 NIC being u sed for SiliconDVR h as the Intel Pro1000 NIC driver software install ed and the NIC can operate as a “normal” NIC, c apabl e of rec eivi ng normal TCP/IP network traffic such as email, in ternet, file-shari ng, etc.
© 2008 Sil icon Imagin g, Inc P age 16 5. After Sili conDVR i s instal l ed, the CineForm in stall er will lau nch. Cli ck though t he “next” button and then when you arrive at the i nstall screen, pres s the “Install” bu tton. 6. After the CineForm Install er completes, the Pleora iPort Vision Su ite wi ll being instal l ation.
© 2008 Sil icon Imagin g, Inc P age 17 8. Once the iPort Visi on Suit e has completed in stall ing, th e Pleora eBUS driver Suite wi ll lau nch. Cli ck though the “Next” button unti l the dri ver is completed insta ll ing .
© 2008 Sil icon Imagin g, Inc P age 18 12. Install ing Drivers: After re booting the computer, go into Program Fil esPleora Technologies IncEthernet BusBinari es and lau nch the EbDriverTool.
© 2008 Sil icon Imagin g, Inc P age 19 16. After the driver instal ls, cl ose the configuration wi ndow. 17. The NIC in the main EbDriverTool window shoul d now read “High Performance Driver” in the driver field. 18. Quit th e EbDriverTool appli cation an d then reboot the computer 19.
© 2008 Sil icon Imagin g, Inc P age 20 3.3 Instal ling SiliconDVR for Ge neric NIC’s: As a pre-installation procedure to optimize the generic NIC and set IP Addresses f or use with SiliconDVR, follow these procedures: 1. Go into the Network Connections dial og box by right- cli cking on Network Neighb orhood and going to “properties”.
© 2008 Sil icon Imagin g, Inc P age 21 6. Press “O kay” to close the TCP/IP proper ties win dow. 7. Next Press “Okay” to close the “Local Area Connection Properties” window.
© 2008 Sil icon Imagin g, Inc P age 22 12. If your NI C provides these properties, se lect the “Transmit Bu ffers” prope rty and set the number of buffers to 512. 13. Press “Okay” to exit the driver configu ration di alog box and th en “Okay” again to exit the “Local Area Connection” properties dia log box.
© 2008 Sil icon Imagin g, Inc P age 23 15. When you reach the “Select Components” screen, make sure that all three selections for CineForm, Pleora eBUS and Pl eora iPort are checke d. 16. Cli ck the “Next” button and proceed with th e instal lati on of Sil iconDV R.
© 2008 Sil icon Imagin g, Inc P age 24 17. After Sil iconDVR i s insta ll ed, the CineForm in stall er will la unch. Cli ck though the “next” button and then when you arrive at the i nstall screen, pres s the “Install” bu tton. 18. After the CineForm Install er completes, the Pleora iPort Vision Su ite wi ll bein g instal l ation.
© 2008 Sil icon Imagin g, Inc P age 25 19. Under the “Setup Type” wind ow select the “Complete” choice for install ati on. 20. Once the iPort Visi on Sui te has completed in stall ing , the Pleora eBUS driver Suite wi ll launch . Cli ck though the “Next” button unti l the dri ver is completed insta ll ing .
© 2008 Sil icon Imagin g, Inc P age 26 21. After the eBUS driver has completed inst all ati on, the instal ler wil l g o back to the Sili conDVR instal l er splash-screen. 22. Once the Sil iconDVR i nstal ler has completed, you wil l be prompted to reboot the co mputer.
© 2008 Sil icon Imagin g, Inc P age 27 24. After rebooting the computer, go into Program Fil esPleora Technologi es IncEthernet BusBin aries and l aunch th e EbDriverTool.exe. 25. Once insid e the EbDriverTool, you should see the active NIC on the computer availabl e for instal l ing the eBUS drivers on for use with Sil iconDVR.
© 2008 Sil icon Imagin g, Inc P age 28 27. Inside the configu ration wi ndow, choose the “ eBU S Universal Driver ” choice. 28. After the driver instal ls, cl ose the configuration wi ndow. 29. The NIC in the main EbDriverTool window shoul d now read “eBUS Universal Dri ver” in the driver field.
© 2008 Sil icon Imagin g, Inc P age 29 3.4 Uninstal ling Previous Versions of Si liconDVR Prior to unin stall in g Sil iconDV R, check the subdirectories for any user information such as .Look libraries that may be stored there and move them to a safe location.
© 2008 Sil icon Imagin g, Inc P age 30 3. In the NIC co nfigu ration wi ndow select “Manufacturer’s NIC Driver”. 4. Press “Finish”. The “Driver” field for either the Pro1000 or the gene.
© 2008 Sil icon Imagin g, Inc P age 31 6. Next go into the “Add/Remove Programs” control panel i n Wind ows XP or the “Pro grams and Features” control panel i n Win dows Vista. Select the eBUS Driver Sui te and then press the “Unin stall ” or “Remove” button.
© 2008 Sil icon Imagin g, Inc P age 32 10. After uninst all in g Sil iconDV R, go back into the “Add/Remove Programs” or “Pro grams and Features” control panel and uni nstall “Cin eForm RAW Codecs”. 11. If it stil l exi sts after the uni nstall of Sil iconDV R, go into Program Fi lesSi li con ImagingS il icon DVR folder.
© 2008 Sil icon Imagin g, Inc P age 33 4.0 Troubleshooting FA Q Why does the right-button mouse -click not stop recording the first time I pr ess it when I sta rted a recording with the external trig.
© 2008 Sil icon Imagin g, Inc P age 34 My “Slave” computer system whe n running a 3D stereo appli cation is ra ndomly dropping frames . What is goin g on? Faul ty sync-signa l cabl es can cause the “slave” SI-2K MINI head to appear to drop frames .
© 2008 Sil icon Imagin g, Inc P age 35 I’m waking up my Windows Vista laptop, but when I launch Sil iconDVR, I only g et a “error connecting to camer a” message. Wha t actions do I take to fix this? In Windows Vist a, connecting to a camera on a lapt op that is woken up from a “sleep” state wil l cause a connection error in Sil iconDVR .
© 2008 Sil icon Imagin g, Inc P age 36 6.0 Sil iconDVR End User License A greement ("EULA ") Thank y ou for becom ing a custom er of Silicon Imaging! W e’re enthused that y ou have chosen to use our Software Products (“Software”) for your Camera Interfac e.
© 2008 Sil icon Imagin g, Inc P age 37 Silicon Imaging does not provi de any , and expressly disclaims all, warranty or representation for these video sam ple files.
© 2008 Sil icon Imagin g, Inc P age 38 result of any term ination of this Agreement. Sections 2 through 9 and S ection 11 shall surviv e term ination of this Agreement.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Silicon Image s1-2k è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Silicon Image s1-2k - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Silicon Image s1-2k imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Silicon Image s1-2k ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Silicon Image s1-2k, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Silicon Image s1-2k.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Silicon Image s1-2k. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Silicon Image s1-2k insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
