Manuale d’uso / di manutenzione del prodotto 100665905 del fabbricante Seagate
Vai alla pagina of 42
Product Manual Momentus ® XT 100665905 Gen-2 Re v . D September 20 11 ST750LX003 ST500LX003.
Revision history © 201 1 Seagate T echnology LLC. All right s reserved. Publication number: 1006 65905, Rev . D, September 201 1 Seagate, Seagate T echnology and the W ave logo are registered trademarks of Seaga te T echnology LLC in the United S tates and/or other coun tries.
Momentus XT Product Manual , Rev. D i Contents 1.0 Seagate Technology support services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii Momentus XT Product Manual, Rev. D.
Momentus XT Product Manual , Rev. D iii List of Figures Figure 1. Typical +5V only startup and operation curren t profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 2. Attaching SATA cabling . . . . . . . . . . . . . . . . .
.
Momentus XT Product Manual , Rev. D 1 1.0 Seagate T e chnology support services SEAGA TE ONLINE SUPPORT and SERVICES For information regarding pr oducts and services, visit http://www .
2 Momentus XT Produc t Manual, Rev. D 2.0 Introduction This manual describes the functiona l, mechanical an d interface specifications for the following Seagate Momentus ® XT model drives: These drives provide the following key fea t ures: • 7200-RPM spindle spee d.
Momentus XT Product Manual , Rev. D 3 2.1 About the Serial A T A interface The Serial A T A interface provides several ad vantages over the traditional (p arallel) A T A interf ace. The p rimar y advantages include : • Easy installation and configur ation with true plug-and-p lay connectivit y .
4 Momentus XT Produc t Manual, Rev. D 3.0 Drive specifications Unless otherwise noted, all specific ations are measure d under ambient conditio ns, at 25°C, and nominal power . 3.1 Spec ification summary table The specifications listed in this tabl e are for quick reference.
Momentus XT Product Manual , Rev. D 5 * One Gbyt e equals one billion bytes when r eferring to hard driv e capacity. Accessible capacity may vary depending on operating environment and formatting. **During periods of drive idle, some offlin e activity may occur acco rding to the S.
6 Momentus XT Product M anual, Rev. D 3.2 Formatted cap acity Model Formatted capacity* Guaranteed sectors Bytes per sector ST750LX003 750GB 1,465,149,16 8 4K emulated @ 512 ST500LX003 500GB 976,773,1 68 *One GB equals one billion bytes when referring to hard driv e capacity.
Momentus XT Product Manual , Rev. D 7 3.3 Default logical geometry Cylinders Read/write heads Sectors per track 16,383 16 63 LBA mode When addressing these drives in LBA mode, all bloc ks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guara nteed sectors as defined above .
8 Momentus XT Product M anual, Rev. D 3.7 Seek time Seek measurement s are t aken with nominal p ower at 25°C ambient tempera ture. All times a re measured using drive diagnostics. The specifications in th e table below are defined as follows: • T rack-to-track seek time is an average of al l possible single-track seeks in both direction s .
Momentus XT Product Manual , Rev. D 9 • Idle mode power Idle mode power is measur ed with the drive up to sp eed, with ser v o electronics active and with the heads in a random track location .
10 Momentus XT Product Manual, Rev. D 3.9.1.1 T ypical current profile Figure 1. T ypical +5V only star tup and operation c urrent profile.
Momentus XT Product Manual , Rev. D 11 3.9.2 C onducted noise Input noise ripp le is meas ured at the host sys tem po we r supply across an equivalent 15-ohm resistive load on the +5V line. Using 5V power , the drive is expe cted to oper ate with a max imum of 100 mV peak-to-pe ak square-w ave injected nois e at up to 10 MHz.
12 Momentus XT Product Manual, Rev. D • Idle and Standby timers Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and begins coun ting down from its spec ified delay times to zero.
Momentus XT Product Manual , Rev. D 13 3.10.6.2 Nonoperating shock The nonoperatin g shock level that the drive can exper ience with out incurring physical d amage or degradation in performance when subsequen tly put into ope ration is 800 Gs based on a nonr epetitive half-sin e shock pulse of 2 ms duration.
14 Momentus XT Product Manual, Rev. D 3.12 Electromagnetic immunity When properly installed in a represen tative host system , the drive operates without errors or degr adation in performance when subjected to the radio frequency (RF) environment s defined in the following table: 3.
Momentus XT Product Manual , Rev. D 15 3.14 Agency certification 3.14.1 Safety certification The drives are reco gnized in accordance with UL 60950-1 and CSA C22.2 (950 ) and meet all applicable sec- tions of IEC 60950-1 and EN60950 -1 as tested by TUV North America.
16 Momentus XT Product Manual, Rev. D 3.14.3 FCC verificatio n These drives are intended to be con t ained solely within a person al com puter o r similar e nclosure ( not att ached as an external device). As such, each drive is consider ed to be a subasse mbly even when it is individually mar- keted to the customer .
Momentus XT Product Manual , Rev. D 17 3.15.2 China Restriction of Hazardous Subst ances (RoHS) Directive This product has an Environ mental Protection Use Pe riod (EPUP) of 20 years.
18 Momentus XT Product Manual, Rev. D 4.0 Configuring and mounting the dri v e This section contains the specif ications an d instructions for configuring and mounting the drive.
Momentus XT Product Manual , Rev. D 19 4.2 Configuring the drive Each drive on the Ser ial A T A interface connects in a point-to-point configuration with the Serial A T A host adapter . There is no master/slave rela tionship because each drive is consid ered a master in a point-to-point relationships.
20 Momentus XT Product Manual, Rev. D 4.4 Drive mounting Y ou can mount the drive using four screws in the side-mo un ting holes or four screws in the bottom-mounting holes. See Figure 3 for drive mounting dimensions. Follow these important mountin g precautions when mount- ing the drive: • Allow a minimum clearance of 0.
Momentus XT Product Manual , Rev. D 21 5.0 Serial A T A (SA T A) interface These drives use the industry-s tandard Ser ial A T A interfac e that supp orts FIS data transfers. It suppor ts A T A programmed inpu t/output (PIO) modes 0–4; multiword DMA modes 0 –2, and Ultra DMA modes 0–6.
22 Momentus XT Product Manual, Rev. D 5.2 Serial A T A device plug conn ector pin definitions T able 7 summarizes the signals on the Seri al A T A interface and power connecto rs. 1. All pins are in a single row , with a 1.27 mm (0.050”) pitch. 2. The comment s on the mating sequence a pply to the case of backplane blindmate connector only .
Momentus XT Product Manual , Rev. D 23 5.3 Supported A T A commands The following t able list s Serial A T A standard comman ds that the drive suppo rts. For a det ailed description of the A T A commands, refer to the Serial A T A: High S peed Serialized A T Attachment specification .
24 Momentus XT Product Manual, Rev. D S.M.A.R.T . Enabl e/Disabl e Autosave B0h/D2h S.M.A.R.T . Enabl e Ope rations B0h/D8h S.M.A.R.T . Enabl e/Disabl e Auto Offline B0h/DBh S.M.A.R.T . Enabl e One Attribute Modification B0h/E0 h S.M.A.R.T . Execut e Offline B0h/D4h S.
Momentus XT Product Manual , Rev. D 25 5.3.1 Identify Dev ice comma n d The Identify Device command (command code EC H ) tran sfers information about the drive to the host following power up. The dat a is organized as a single 51 2-byte bl ock of data, whose content s are shown in the ta ble on page 27.
26 Momentus XT Product Manual, Rev. D 60–61 T otal number of user-addressable secto rs This field contains a value that is one greater th an the total number of user-addressable sectors. Th e maxi mum value that shall be pl aced in this field i s 0FFFFFFFh.
Note. See the bit descriptio ns belo w for words 63, 88, 93 and 94 of the Identify Drive data: Description (if bit is set to 1) Bit Wor d 6 3 0 Multiword DMA mode 0 is supported . 1 Multiword DMA mode 1 is supported . 2 Multiword DMA mode 2 is supported .
28 Momentus XT Product Manual, Rev. D 5.3.2 Set Featu res command This command controls the implemen tation of various fe at ur es that the drive su pports. When the drive receives this command, it sets BSY , checks the contents of the Features r egister , clears BSY and generate s an inter- rupt.
Momentus XT Product Manual , Rev. D 29 SeaT ools diagnostic sof tware activates a built-i n drive self-test (DST S.M.A.R.T . command for D4 H ) that elimi- nates unnece ss ar y driv e re tu rn s. Th e diagnostic software ship s with all new drives and is also available at: http://seatools.
30 Momentus XT Product Manual, Rev. D.
Momentus XT Product Manual , Rev. D 29 Index A ACA 14 acoustics 5 , 12 Active m ode 10 Address 22 AFR 13 Agency certification 14 Altitude 11 Altitude, nonoperating 5 Altitude, operating 5 Ambient temp.
30 Momentus XT Product Manual, Rev. D H handling 17 Handling precautions 17 heads 7 Height 4 height 7 humidity 5 I I/O data-transfer rate 4 , 7 Identify 22 Identify Device 22 Identify Device command 2.
Momentus XT Product Manual , Rev. D 31 read/write power and current 8 Recording density 4 , 7 Recording method 7 Recording technology 7 Relative humidity 5 , 11 Reliability 13 resistance 10 Retries 22 RF 13 RoHS 15 , 16 RPM 4 RRL 14 S S.M.A.R.T. 23 S.
32 Momentus XT Product Manual, Rev. D.
.
Seagate T echnology LLC AMERICAS Seagate T echnology LLC 10200 South De Anza Boul evard, Cupertino, C alifornia 95014, United States, 408-658-1000 ASIA/P ACIFIC Seagate Singapor e Inte rnational Headquarters Pte.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Seagate 100665905 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Seagate 100665905 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Seagate 100665905 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Seagate 100665905 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Seagate 100665905, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Seagate 100665905.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Seagate 100665905. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Seagate 100665905 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
