Manuale d’uso / di manutenzione del prodotto 100 del fabbricante PYLE Audio
Vai alla pagina of 17
Router Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e refer ence. Model No. ______________________________________ T ype ___________________________________________ Serial No.
2 Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could result in serious injury and pr operty damage.
3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer , birth defects or other reproductive harm.
4 Read all instructions. Failure to follow all instructions listed below may result in electric shock, fir e and/or serious injury . The term "power tool" in all of the war nings listed below refers to your mains-operated (cor ded) power tool or battery-operated (cordless) power tool.
5 d) Remove any adjusting key or wrench befor e tur ning the power tool on. A wrench or a key left attached to a r otating part of the power tool may result in personal injury . e) Do not overreach. Keep pr oper footing and balance at all times. This enables better control of the power tool in unexpected situations.
6 1. HOLD POWER TOOL BY INSULA TED GRIPPING SURF ACES WHEN PERFORMING AN OPERA TION WHERE THE CUTTING TOOL MA Y CONT ACT HIDDEN WIRING OR ITS OWN CORD. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator .
7 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ...................
8 EXTENSION CORD SELECTION If an extension cord is used, make sur e the conductor size is lar ge enough to prevent excessive voltage dr op which will cause loss of power and possible motor damage. A table of recommended extension cor d sizes will be found in this section.
9 FOREWORD The router is one of the most useful tools in the woodworking field. It may be used for many cutting and shaping operations such as slotting, mortising, dadoing, grooving, rabbeting, corner -rounding, beading, dovetailing, veining, inlay work, etc.
10 1. T o remove motor unit from base unit: Open the clamp (A) Fig. 1. While holding base, turn power unit COUNTERCLOCKWISE until lower pin (B) in motor housing is disengaged from gr oove in base. Lift power unit free fr om base unit. 2. Clean and insert shank of bit into collet until shank bottoms, then back it out approximately 1/16".
11 NOTE: Setting the index line to 1/4" on the ring means the cutting edge of the bit is exposed 1/4" below the base. CONNECTING TO POWER SOURCE Before connecting tool to power sour ce AL WA YS MAKE SURE SWITCH IS IN THE “OFF” POSITION. Also check that the power circuit is the same as that shown on specification plate of the router .
12 USING THE ROUTER IMPORT ANT : Before using your router , consider the kind and total amount of material to be removed. Depending on the workpiece, mor e than one cut may be necessary to avoid overloading the motor .
13 TEMPLET GUIDES A wide variety of templet guides is available for use in pattern and templet routing operations. Fig. 7 shows a typical combination bit, templet guide, and locknut. DISCONNECT TOOL FROM POWER SOURCE. T o install, insert templet guide in center hole of router base and secure in place with the locknut.
14 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air . All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.
15 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter -Cable warrants its Professional Power T ools for a period of one year from the date of original purchase.
16 NOTES.
The following are trademarks of PORTER-CABLE • DEL T A (Las siguientes son marcas registradas de PORTER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il PYLE Audio 100 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del PYLE Audio 100 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso PYLE Audio 100 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul PYLE Audio 100 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il PYLE Audio 100, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del PYLE Audio 100.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il PYLE Audio 100. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo PYLE Audio 100 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
