Manuale d’uso / di manutenzione del prodotto WLV2500 del fabbricante Pelco
Vai alla pagina of 20
® P elco • 3500 Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981 FAX (800) 289-9150 or (1-559) 292-3827 WL V2500 Series Wir eless Control Link and V ideo T ransmission Syst.
ii Pelco Manual C914M (7/96) ®Pelco and the Pelco logo are registered trademarks of Pelco. ©Copyright 1996, Pelco. All rights reserved. T ABLE OF CONTENTS Section Page 1.0 W ARNINGS ...................................................................
LIST OF ILLUSTRA TIONS Figur e Page 1T ypical WL V500 Control Link and WL V2000 Video Link Configuration ............................................ 2 2T ransmitter-Receiver Placement at Same Site .....................................................
(This page intentionally left blank.) iv Pelco Manual C914M (7/96).
Pelco Manual C914M (7/96) 1 This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN. Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.
2 Pelco Manual C914M (7/96) 2.0 SCOPE This manual covers the installation of the WL V2500 Series of outdoor wireless systems. 3.0 DESCRIPTION To make a WL V2500 system, a WL V500 control sys- tem is combined with a WL V200 video transmission system (refer to Figure 1).
Pelco Manual C914M (7/96) 3 Figure 2. T ransmitter-Receiver Placement at Same Site 4.0 ANTENNA LOCA TION To provide the best reception, proper placement of the transmit and receive antennas is important. Reception will be best when: • The antennas are a minimum of 8-10 feet above the floor (indoors) or ground (outdoors).
4 Pelco Manual C914M (7/96) 5.0 INST ALLA TION NOTE: Proper placement of the transmit and receive antennas is important for best reception. Read Section 4.0, “Antenna Lo- cation,” before installing the equipment. Install the WL V500 receiver and WL V2000 transmit- ter at the remote site where your camera will be.
Pelco Manual C914M (7/96) 5 5.2 WIRING NOTE: In the following steps w hen you as- semble coaxial cable, install a BNC connector on only one end. Run the bare end of the cable through the cable entry gland on the enclosure so that the end with the BNC connector is inside the enclosure.
6 Pelco Manual C914M (7/96) 5.4 ANTENNA ALIGNMENT NOTE: This section applies only to the WL V2000 wireless receiver . 1. Connect a high impedance voltmeter to the RSSI (Received Signal Strength Indication) test points on the bottom of the enclosure: a.
Pelco Manual C914M (7/96) 7 4. Check the power supply voltages for the wireless transmitter and receiver . If the voltage at the trans- mitter or receiver is less than 1 1 VDC, replace the unit’ s power supply . 5.5.2 Poor Picture 1. Refer to Section 4.
8 Pelco Manual C914M (7/96) 6.0 EXPLODED ASSEMBL Y DIAGRAM (OUTDOOR MODELS ONL Y) Figure 6. Outdoor Enclosure Exploded Assembly Diagram.
Pelco Manual C914M (7/96) 9 6.1 MECHANICAL P ARTS LIST Item Quantity Description Part Number 11 9-Pin Connector CON03-06-1091 22 Gland EH400010003 32 Gland Nut EH400010004 41 Gland CX950010000 51 Gland Nut CX950010001 62 Fuse Holder FUS342012L 71 Power Supply Assembly PCB9000281ASSY 81 3-Position T erminal Block TRB3-140Y 91 Tr ansformer T RF21162.
10 Pelco Manual C914M (7/96) 7.0 INTERCEPT ® DOME MODIFICA TION To use the WL V500 wireless control system with In- tercept ® dome drives DD08CXX, DD08EXX, DD14CXX, or DD14EXX (domes with 360 degree.
Pelco Manual C914M (7/96) 11 Figure 8. V ideo Board Component Locations Figure 9. Block Diagram.
12 Pelco Manual C914M (7/96) Figure 10. Coaxitron ® Receiver Backplane PCB - Wire Lead Additions and Wiring Diagram.
Pelco Manual C914M (7/96) 13 8.0 WIRING DIAGRAM NOTE: Output voltage is 15 VDC, not 10.5 Figure 1 1. Outdoor Enclosure Wiring Diagram 9.0 MAINTENANCE In cold, wet areas periodically visit the transmitter and receiver sites to prevent the buildup of snow and ice on the enclosures.
14 Pelco Manual C914M (7/96) Impedance: 75 ohms Connectors: BNC RF (WL V500) T ransmitter Radiated Power: FCC Part 15 (15.249) T ransmit Antenna: Attached, circular -polarized, patch antenna Receive A.
Pelco Manual C914M (7/96) 15 11.0 W ARRANTY AND RETURN INFORMATION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 1996, Pelco. All rights reserved.
Pelco 3500 Pelco Way, Clovis, CA 93612-5699 (559) 292-1981 • (800) 289-9100 FAX (800) 289-9150 or (559) 292-3827 International customers call 1-559-292-1981 or FAX 1-559-348-1120 (Product specifications subject to change without notice.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Pelco WLV2500 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Pelco WLV2500 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Pelco WLV2500 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Pelco WLV2500 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Pelco WLV2500, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Pelco WLV2500.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Pelco WLV2500. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Pelco WLV2500 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.