Manuale d’uso / di manutenzione del prodotto Not ICS110-CW del fabbricante Pelco
Vai alla pagina of 28
INST ALLA TION ICS110-CW Series Camclosure ® Integrated Camera System Wide Dynamic Range (WDR) C3406M-D (1/07).
.
C3406M-D (1/07) 3 Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 C3406M-D (1/07) List of Illustrations 1 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 Basic Surface Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .
C3406M-D (1/07) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
6 C3406M-D (1/07) Description The ICS110-CW Series Camclosure ® integrated camera system combines an environmental cover, back box, camera, lens, and lower dome into a small, high-security system that is quick and easy to install.
C3406M-D (1/07) 7 Figure 1. Package Components COVER AND BACK BOX (1) CAMERA MODULE (1) TRIM RING, DOME LINER, AND CLEAR BUBBLE (1) TRIM RING AND SMOKED BUBBLE (1) < OR > 1/8-INCH HOLLOW SCREWDRIVER BIT (1) BLACK PLUG (1) SHOWN ACTUAL SIZE SHIPPING BOX 8-32 X 0.
8 C3406M-D (1/07) Cover and Back Box Installation The ICS110-CW Series Camclosure integrated camera system mounts only to a surface. It can be wired through the cover into a surface, electrical box, or plaster ring. Y ou can also wire it through a side conduit.
C3406M-D (1/07) 9 8. Reinstall the back box inside the cover. For vandal-resistant installations, rotate the back box to position the conduit plug opposite the notch on the side of the cover. Use the two 8-32 x 0.375-inch Phillips pan head screws and washers (removed earlier) to secure the back box to the cover .
10 C3406M-D (1/07) 6. Connect the power wires. AC operation only: If you are wiring more than one Camclosure integrated camera system to the same transformer , connect one side of the transformer to the red wire on all units, and connect the other side of the transformer to the black wire on all units.
C3406M-D (1/07) 11 404 PLASTER RING INSTALLATION NOTE: Y ou should install the camera module into the back box before installing the back box into the cover . When installing the back box into the cover, rotate the camera module to access the mounting holes.
12 C3406M-D (1/07) 5. Reinstall the back box inside the cover. For vandal-resistant installations, rotate the back box to position the conduit plug opposite the notch on the side of the cover. Use the two 8-32 x 0.375-inch Phillips pan head screws and washers (removed earlier) to secure the back box to the cover .
C3406M-D (1/07) 13 7. Install a 0.75-inch (1.91 cm) threaded conduit connector (not supplied) into the conduit hole in the back box. Figure 5. Side Conduit Installation 8. Connect the video cable/wires: BNC: Connect the BNC connector from the unit to a mating BNC connector.
14 C3406M-D (1/07) Camera Module The ICS110-CW Series Camclosure camera module includes the camera, camera bracket, and heater board. T o perform most camera adjustments, you must remove the module from the back box. Use the following instructions to remove and reinstall the camera module.
C3406M-D (1/07) 15 2. Unplug the camera (10-pin), heater board (four-pin), and service (three-pin) connectors from the back box (refer to Figure 7). Figure 7.
16 C3406M-D (1/07) CAMERA ORIENTATION At the factory , the camera module is confi gured for ceiling mounting. For wall mounting, you must change the camera orientation or the video image will be upside down. T o change the camera orientation (refer to Figure 8): 1.
C3406M-D (1/07) 17 Camera Adjustments T o perform the following camera adjustments, make sure to plug in the camera and service connectors. Y ou may have to remove the camera module from the back box. Connect a monitor . Then turn on power to the camera and monitor.
18 C3406M-D (1/07) SWITCH SETTINGS Locate the DIP switch (refer to Figure 10). Then set the switches for your installation. Figure 10. DIP Switch SW1: Video Format Set to ON for NTSC. Set to OFF for PAL. The default is ON. SW2: Line Sync Set to ON to use AC line lock.
C3406M-D (1/07) 19 Extended dynamic range: Use for extremely high dynamic installations, for example, doorways, entrances, and exits. This profi le offers the maximum wide dynamic range. Fluorescent: Use for any installation with fl ickering lighting of any kind.
20 C3406M-D (1/07) Camera Positioning Manually rotate and tilt the camera module to position the camera. Then tighten the tilt screws (axis in Figure 12). NOTE: Do not over-rotate the module. Excessively turning the module in one direction could result in damage to the wiring.
C3406M-D (1/07) 21 Install Dome and T rim Ring 1. Adjust the dome liner if installed (refer to Figure 13): a. Align the screw holes in the trim ring with those in the back box to identify the proper dome liner position. b. Loosen the three Phillips screws located in the trim ring.
22 C3406M-D (1/07) Service Connector The ICS110-CW Series Camclosure integrated camera system includes a service connector that outputs camera video. Use it at the installation site to set up the fi eld of view and focus the camera. Figure 14. Service Connector Pelco offers two optional items that plug directly into the service connector .
C3406M-D (1/07) 23 T o assemble a longer service cable for the Camclosure integrated camera system, purchase the following from a local electronics supply store: 1 2.5 mm monaural headphone plug 1 CPM 88 miniature coaxial connector 1 RG174/U coaxial cable T o assemble the cable: 1.
24 C3406M-D (1/07) Specifications CAMERA Imaging Device 1/3-inch imager Dynamic Range 102 dB typical/120 dB maximum Picture Elements Sensor resolution: 742 (H) x 552 (V) Signal System NTSC or PAL Sca.
C3406M-D (1/07) 25 BACKBOX Electrical Input Voltage** 12 VDC or 24 VAC (±10%), autosensing Power Consumption 10 watts or less Video Connector Composite: BNC UTP: T wisted pair General Pan/T ilt Adjus.
26 C3406M-D (1/07).
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repa ir or replace, without charge, any merc ha ndise proved defective in material or wo rkmanship for a period of one year after the date of shipment.
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Pelco Not ICS110-CW è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Pelco Not ICS110-CW - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Pelco Not ICS110-CW imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Pelco Not ICS110-CW ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Pelco Not ICS110-CW, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Pelco Not ICS110-CW.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Pelco Not ICS110-CW. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Pelco Not ICS110-CW insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
