Manuale d’uso / di manutenzione del prodotto DX8000-UPDVD del fabbricante Pelco
Vai alla pagina of 24
DX8000-UPDVD Upgrade Installation Manual C1604M (6/04) Digital Video Recorder DX8000.
Protecting people and property in a million locations worldwide..
C1604M (6/04) 1 Introduction The following instructions serve as an installation guide for the DX8000-UPDVD drive kit. PARTS LIST NOTE: This upgrade kit includes a Pelco-certified DVD-RW drive. Using any other drive voids the manufacturer’ s warranty for the DX8000.
2 C1604M (6/04) Getting Ready 1. Familiarize yourself with the instructions throughout this manual. 2. Check that you have all the necessary parts and tools.
C1604M (6/04) 3 Figure 2. Removing Power Cord from Unit.
4 C1604M (6/04) Figure 3. ESD Protection 5. Ensure that the DX8000 Series DVR and all of its components are protected against electrostatic discharge (ESD). Before handling any electronic components, you should take steps to ground yourself properly so that any built-up static electric charges are dissipated away from the unit.
C1604M (6/04) 5 Prepare Unit for Drive Installation OPEN THE UNIT CHASSIS WARNING: The chassis assembly includes parts with sharp edges. T o avoid injury , use caution when working in and around the DX8000’ s chassis and components.
6 C1604M (6/04) 3. Using a Phillips-head screwdriver , remove the chassis cover: WARNING: Make sure unit is turned off and you are wearing a properly grounded ESD wrist strap before attempting to open the DX8000 chassis cover . Refer to the Getting Ready section.
C1604M (6/04) 7 4. Using a Phillips-head screwdriver , remove the side panel from the side of the unit closest to the CD/DVD drive: a. Remove the four screws from the side panel. Refer to Figure 5. b. Set the panel and screws aside for use later . Figure 5.
8 C1604M (6/04) COMPONENT LA YOUT Figure 6 shows the location of your DX8000 Series DVR’ s major components. Certain cables and components have been omitted from the illustrations in this manual for the purpose of clarity .
C1604M (6/04) 9 Remove the Existing Optical Drive DISCONNECT THE CD/DVD DA T A CABLE AND POWER WIRES When removing data cable and power wires, pull the connectors straight out. Do not rock connectors back and forth or remove a connector by pulling it by its wires or cable.
10 C1604M (6/04) 2. Remove the power connector from the CD/DVD drive. Refer to Figure 8. 2 Figure 8. Removing the CD/DVD Power Connector.
C1604M (6/04) 11 REMOVE THE CD/DVD DRIVE 1. Using a Phillips-head screwdriver , unfasten the two screws that attach the CD/DVD to the chassis. Refer to Figure 9.
12 C1604M (6/04) 2. Gently pull the CD/DVD drive out of the DVR through the front of the unit. Refer to Figure 10. 2 Figure 10. Removing the Existing Optical Drive.
C1604M (6/04) 13 Install the New DVD-RW Drive into the Unit 1. Insert the new DVD-RW into the DVR: a. Make sure the drive is oriented correctly . b. Insert the new DVD-RW into the DVR through the front of the unit.
14 C1604M (6/04) c. Using a Phillips-head screwdriver and the two screws provided in the upgrade kit, secure the drive to the unit’ s chassis. Refer to Figure 12.
C1604M (6/04) 15 RECONNECT THE DA T A CABLE AND POWER WIRES IMPORT ANT : Data and power connectors fit together only one way . All connectors are keyed to ensure that they are inserted in the proper orientation. Examine the drive, motherboard and cable connectors before installation so that connectors are properly aligned.
16 C1604M (6/04) 2. Connect the DVD-RW drive to the system motherboard using the existing data cable. Refer to Figure 14. 2 Figure 14. Installing DVD-RW Data Cable.
C1604M (6/04) 17 Reassemble the Unit 1. Using a Phillips-head screwdriver , reattach the side panel you removed earlier . Refer to Figure 15. Figure 15.
18 C1604M (6/04) 2. Replace the chassis cover using the same screws you removed from the side and rear of the unit. Refer to Figure 16. Figure 16. Replacing Chassis Cover.
C1604M (6/04) 19 4. Reinstall the unit in a rack enclosure if necessary , and reconnect all cables and peripheral equipment that you removed earlier . 3. Plug the power cord back into the power supply and then into the wall. 4. T urn on the power switch and allow the unit to start up and find the new DVD-RW .
20 C1604M (6/04) Notes.
PRODUCT WARRANTY AND RETURN INFORMA TION PRODUCT WARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
Pelco and the Pelco logo are registered trademarks of Pelco. © Copyright 2004, Pelco. All rights reserved. Windows is a registered trademark of Microsoft Corporation.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Pelco DX8000-UPDVD è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Pelco DX8000-UPDVD - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Pelco DX8000-UPDVD imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Pelco DX8000-UPDVD ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Pelco DX8000-UPDVD, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Pelco DX8000-UPDVD.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Pelco DX8000-UPDVD. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Pelco DX8000-UPDVD insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
