Manuale d’uso / di manutenzione del prodotto SVL-2 del fabbricante Niles
Vai alla pagina of 16
SV L- 2 INSTALLATION & OPERA TION GUIDE N I LES ® MODEL SV L - 2 SPEAKER SEL EC TION /VOLUME CONTROL SYSTEM SV L- 2.
Introduction The SVL-2 is a combination speaker selector and volume con- troller. It allows you to connect two pairs of speakers to your stereo receiver or amplifier and adjust the volume of each pair independently. Additionally, you can choose to listen to either pair of speakers, or both pairs simultaneously.
Features and Benefits The SVL-2 offers a number of improvements over other speaker selector/volume controllers: ● The SVL-2 uses 1 2 position volume controls which are superior to 1 0 position designs. You get a broader range of adjustment — there are 1 0 steps of attenuation instead of 8.
● Spring-loaded push terminal connectors accommodate up to 1 4 gauge wire or "pins", making the SVL-2 compatible with most "high-definition" speaker cables. ● 1 00% tested, electronically and acoustically, for frequency response, distortion and power handling.
Installation Considerations SVL-2 Power Handling The SVL-2 is designed for use with a receiver or amplifier hav- ing a maximum power output of 1 00 watts per channel at 8 ohms. Damage caused by the use of a higher-power receiver or amplifier will void the warranty.
The SVL-2 includes impedance correction circuitry which protects your receiver or amplifier from low impedance loads. The circuitry assures that your receiver or amplifier will see a safe operating load, even when two pairs of 4-ohm speakers are playing at the same time.
near electrical devices, route the speaker wires several feet away from the electrical wiring. Using the SVL-2 with Tube-Type Amplifiers Virtually all tube amplifiers must have a load connected at all times.
7 S PEAKER S ELECTION /V OLUME C ONTROL S YSTEM SVL-2 SPEAKER SELEC T ION/ VOLUM E C ONT ROL S YS TEM PRO T EC T ION 12 N I LES SPE AK ER 2 SPE AKER 1 LR AMP L IFIER LR LR ++ -- ++ -- Niles Aud io Corpor ati on, Inc .
Installation 1. Select a convenient location for the SVL-2. 2. Run all the necessary wiring to the SVL-2. Label the wires for future reference. See (Figure 2). 8 S PEAKER S ELECTION /V OLUME C ONTROL S YSTEM F igure 2 Wiring Diagram TUNER 94.9 15 SPE AKER 2 SPE AKER 1 LR AMPLIFIER LRLR ++ -- ++ -- Niles Audio Corpor at i on, Inc.
3. Make the connections to the SVL-2. Strip 3 /8" of insulation from the end of each wire. Tightly twist the end of each wire until there are no frayed ends.
Operation The are two ways to use the SVL-2. You may play and adjust the volume of either pair of speakers independently, or both pairs simultaneously. If you intend to play both pairs simultaneously, and either pair is less than 8 ohms, you will need to become familiar with the operation of the SVL-2's PROTECTION button.
S PEAKER S ELECTION /V OLUME C ONTROL S YSTEM 6. Using the appropriate volume control on the front of the SVL-2, adjust the volume of the speakers to the desired listen- ing level. 7. You can turn off the speakers by turning the appropriate volume control on the SVL-2 fully counter-clockwise, or by pressing the ON/OFF button.
12 3. Set both SVL-2 volume controls to maximum. 4. Locate the ON/OFF buttons on the SVL-2. Set both to the ON position. 5. Turn on the amplifier or receiver and select as source, such as the tuner or CD player. 6. Slowly turn up the amplifier or receiver volume and set it to a comfortable (not maximum) listening level.
13 S PEAKER S ELECTION /V OLUME C ONTROL S YSTEM Balancing Speaker Volume The volume control on your receiver or amplifier serves as the "master" volume for all speaker pairs connected. The volume level of the speakers may vary from room to room.
14 S PEAKER S ELECTION /V OLUME C ONTROL S YSTEM SPECIFICA T IONS Audio Power Handling 100 watts/channel continuous music power Frequency Response +/- 1.2 dB from 20 Hz to 20 kHz Mounting Table-top component Wiring Requirements Individual runs of 2-conductor speaker wire.
Niles Audio Corporation www.nilesaudio.com 1 233 1 S. W . 1 30 Street Miami, Florida 3 3 1 86 T el: (305) 238-43 73 Fax: (305) 238-0 1 85 ® NIL E S ® © 1 999 Niles A udio Corporation.
Un punto importante, dopo l’acquisto del dispositivo (o anche prima di acquisto) è quello di leggere il manuale. Dobbiamo farlo per diversi motivi semplici:
Se non hai ancora comprato il Niles SVL-2 è un buon momento per familiarizzare con i dati di base del prodotto. Prime consultare le pagine iniziali del manuale d’uso, che si trova al di sopra. Dovresti trovare lì i dati tecnici più importanti del Niles SVL-2 - in questo modo è possibile verificare se l’apparecchio soddisfa le tue esigenze. Esplorando le pagine segenti del manuali d’uso Niles SVL-2 imparerai tutte le caratteristiche del prodotto e le informazioni sul suo funzionamento. Le informazioni sul Niles SVL-2 ti aiuteranno sicuramente a prendere una decisione relativa all’acquisto.
In una situazione in cui hai già il Niles SVL-2, ma non hai ancora letto il manuale d’uso, dovresti farlo per le ragioni sopra descritte. Saprai quindi se hai correttamente usato le funzioni disponibili, e se hai commesso errori che possono ridurre la durata di vita del Niles SVL-2.
Tuttavia, uno dei ruoli più importanti per l’utente svolti dal manuale d’uso è quello di aiutare a risolvere i problemi con il Niles SVL-2. Quasi sempre, ci troverai Troubleshooting, cioè i guasti più frequenti e malfunzionamenti del dispositivo Niles SVL-2 insieme con le istruzioni su come risolverli. Anche se non si riesci a risolvere il problema, il manuale d’uso ti mostrerà il percorso di ulteriori procedimenti – il contatto con il centro servizio clienti o il servizio più vicino.
